Question about Cars & Trucks

Open Question

Place jack when changing tire on Suzuki xl7

Where do you put the jack to raise car when changing a flat

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Jack Location for Tire Change

under the back seats, jack is under the driver's side backseat, tire iron & rods are under passenger's side backseat.

Posted on Aug 24, 2008

keemo68
  • 1263 Answers

SOURCE: Flat Tire - 2007 Honda Fit

not that I'm aware of sometimes they stick on the center part of the hub it happens to all vehicles. what I normally do is just kick the top of the tire a couple of times this usually does the trick.

Posted on Oct 05, 2008

  • 3 Answers

SOURCE: jack position to change rear tire 98 pontiac grand prix

factory jack to be placed in front of tire inbetween notches on seem. A manual floor jack can be used placing it under center connection bracket for rear wheels. Be shure to block front tires when using floor jack and have car in gear if a manual or park if automatic transmision.

Posted on Mar 31, 2009

mecanica03
  • 874 Answers

SOURCE: 1991 lexus ls 400 Height Control Reset

this strut goes off,replace

Posted on Apr 15, 2009

  • 136 Answers

SOURCE: I have a 2005 Suzuki XL7 tire pressuer sensor that won't go out!

I hate tire pressure monitors, in this case it sounds like you have a bad one. if you take it to the dealer they will be able to tell you which one is bad.

MIKE

Posted on May 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jack placement for rear tire change? This seems the most sensible place, but it isn't lifting enough.


Looks like that would be OK. Can you lower it again and put a block of wood under the jack? Those jacks also work on the axle if it is rear wheel drive. Or maybe there is room to put the jack under the spring support right beside the wheel? I have been in a similar pinch before, where it would not raise enough. I used one jack to raise as far as it could, then used another jack in a second location to raise the wheel higher. There is always a way. First try a block under that jack.

Jun 29, 2015 | Cars & Trucks

1 Answer

How do i change rear wheel tire in isuzu trooper


Loosen lugs first. Chock opposite front wheel. Put emerengcy brake on. Jack up vehicle where the rear spring meets with the frame. Raise vehicle about 1 inch swap tires. Install lugs snug. Lower vehicle till tire just touches the ground then tighten lugs. Finish lowering the jack and remove chock place both in vehicle.
Start truck, release jack and continue on your way. Make sure spare has proper amount of air. If not go to gas station and fill tire. If low on air do not go over 30 mph. Hope this helps.

Sep 26, 2014 | 1999 Isuzu Trooper

1 Answer

Torque wheel nuts xl 7


open glove box door.
take out operators guide, turn to page tire change out, bingo
02 xl7

lug nuts?
ever google, here ill type for you ......

https://www.google.com/search?q=2007+suzuki+xl7+lug+nut+torque&ie=utf-8&oe=utf-8

Bingo>? rumors, yes, best is real books, on your car, the FSM book or the operators guide for TRUTH.

Jun 03, 2014 | 2002 Suzuki XL-7

1 Answer

Hi - This is really a dumb question, but my daughter's suzuki is in the southern states and I am on the west coast. Please tell me where the car jack should go to change both the front and rear tires?


it goes next to the tire but not to close find a strong flat part which is metel under the car next to to the tire and place the jack there pump it up and if the jack is slipping and looks like it will not hold try a different spot but again not far from the tire ur changing u want to left the weight off that tire. before u jack the car up take the lug nuts off the tire so it does not turn while its in the air hand screw the nut on the new tire tighten them up then drop the car off the jack and tighten them up even tighter repeat step for other side. the nuts might be tight to get off so use a lot of muscle to get them loose.

May 16, 2011 | 2002 Suzuki Aerio

1 Answer

Ho wdo you replace the shocks on an xl7 do you have to compress the font end in order to put shocks on?


It is a little easier to raise the vehicle to remove the shock unit. Once the top is in place and the bolt/nut is on just enough to hold it in place, raise the control arm just enough with a jack to bring the bottom in line and secure it. No real tricks other than that.

Apr 29, 2011 | Suzuki XL7 Cars & Trucks

1 Answer

Changing rear flat tire


Find jack follow instructions to raise vehicle after parking brake is on. Remove lug nuts and take wheel with flat tire off. Replace with the spare tire and tighten lug nuts. lower vehicle, put jack , lug wrench and flat tire in vehicle. Drive to a tire repair store and fix the problem.

Dec 11, 2010 | 1996 Dodge Caravan

1 Answer

Flat tire


your owners manual is a valuable source of information, but if you do not have it here is what you do: the vehicle should be on a flat hard surface then you need to locate your jack and lug wrench , with the vehicle still on the groung loosen each lug nut about one turn then make sure that your emergency break is on, place the jack under the vehicle in an appropreate spot to raise the wheel off the groung, once the wheel is off the ground you can remove the lug nuts and pull the wheel off. Then you can put the spare tire on and replace the lug nuts tighten them in a criss cross patern as tight as you can get them then lower the vehicle back to the ground and check the lugs again. I hope this helps, good luck !!

May 12, 2010 | 2001 GMC Yukon XL

2 Answers

My 2007 suzuki xl7 service tire monitor system light stays on


Dear sir,
my 2007 suzuki xl7 service tire monitor system light stays on

Oct 20, 2009 | 2006 Suzuki XL-7

1 Answer

I have a 2005 Suzuki XL7 tire pressuer sensor that won't go out!


I hate tire pressure monitors, in this case it sounds like you have a bad one. if you take it to the dealer they will be able to tell you which one is bad.

MIKE

May 28, 2009 | 2005 Suzuki XL-7

2 Answers

How to change the tire


First off did you Know this ?????

Make / Models : Model/Build Years:
GMC / 1500 2004
Regency / Chevrolet 1500 2004
MANUFACTURER: General Motors Corp.
NHTSA CAMPAIGN ID Number : 04V240000 Recall Date : MAY 14, 2004
COMPONENT: Tires: Temporary/Emergency Spare Tire
Potential Number Of Units Affected : 285
SUMMARY:
The spare tire and wheel assembly that was provided on certain conversion vehicles will not fit on the front wheel hub due to offset of the wheel. However, it will fit on the rear wheels.
CONSEQUENCE:
If someone has a flat tire on the front wheel, they will not be able to install the provided spare tire.
REMEDY:
Dealers will install a spare wheel with the correct offset. Owner notification began on June 11, 2004. Owners should contact Regency at 1-800-989-4727.
NOTES:
Customers can also contact The National Highway Traffic Safety Administration's Auto Safety Hotline at 1-888-DASH-2-DOT (1-888-327-4236)

SPARE TIRE is Under rear of truck use Long Cranking in HoleClose to Lisence Plate to Lower it Down Cranking Counter Clockwise. Wing in center of Wheel pokes thrugh Hole in Center of wheel
Reverse Procedure to Put old tire in Tire Storage Compartment

  1. Locate Jack & Wheel Lug Nut Wrench
  2. There is Directions as to where to placse the Jack for raising Truck Where Jack is Located
  3. Set Park Brake Chalk tire if possible & Hazard lights (If on the Roadside)
  4. Loosen all Wheel Nuts on said wheel before Raising Vehicle
  5. Place Jack In Recomended Placment spot
  6. Rear is Normaly on Axel close to Shock
  7. Front is Normaly on FRAMERAIL
  8. Raise vehicle untill tire is 3-4 inches off ground as Flat will Lower vehicle
  9. Remove All Wheel Nuts And Wheel
  10. Place new wheel/tire on Vehicle and start all nuts
  11. Tighten nuts as tight as Possible then Lower Vehicle Untill tire touches ground Good
  12. Now Toque Wheel Nuts as tight as Possible with hand tool
  13. Lower vehicle all the way down
  14. Put away tools and Reliece Park Brake
  15. Torque should be around 100-130 foot Pounds

I Hope this is What You Wanted Its Off the Cuff as My Reference Books done have this Procedure.


Jan 26, 2009 | 2004 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...