Question about Cars & Trucks

Open Question

Cobra car alarm key fob model 6657 reset - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 80668 Answers

SOURCE: key fob will not undo

If you don't have one that works for the vehicle now, you'll have to take it to your local dealer to have it programmed to the vehicle. Some will charge for this, some will do it at no charge.

If you do have a remote that is programmed and working for the vehicle, then the following steps will allow you to program another remote:

1. Enter vehicle and close all doors.

2. Put seatbelt on (or clip it into the buckle) to shut the warning buzzer off.

3. Put key in ignition, turn to run position but don't start it.

4. Press and hold the unlock button on the working key fob and hold for 4 seconds, then also press the panic button.

5. Release both buttons and you should hear a single chime to indicate it is in program mode. You have 30 seconds after the chime to program any additional remotes you want to program.

6. Press and release both the unlock and lock buttons simultaneously on the remote you are programming. You should hear another single chime.

7. Within 4 seconds after hearing the chime, press either lock or unlock button on remote that you are programming.

Posted on Oct 16, 2008

Ad
  • 1 Answer

SOURCE: car alarm preventing car from starting

I am having trouble also but I need to know how to disconnect the alarm. I would appreciate it if you could help me out seeing that you have disconnected yours. Thank you

Posted on Jun 04, 2009

  • 1 Answer

SOURCE: car alarm how to reset a cobra alarm after fitting a new batt.

i put a new battery on my car and now the alarm will not work

Posted on Oct 09, 2009

Molson02536
  • 3854 Answers

SOURCE: How do I reset a Key Fob for my 2006 Grand Prix

No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.

Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.
Perform the following steps: Sit in the vehicle driver's seat. (actually it’s much ezr from the front pass seat)
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.

Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation

Posted on Nov 13, 2009

roniecon
  • 6927 Answers

SOURCE: how do you re-link the key fob to the car after

Try this,,turn the key on ,wait 10 minutes,then turn the key off,then right back on,do this three times,a total of 30 minutes,this should reset the key fob,if this is the problem.

Posted on Apr 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset my cobra alarm without a fob after push button in cab was activated. I have code.


Go to the cobra site, trouble shooting. Never have put an alarm in. But have tore out hundreds of them. Anytime I get a No start or problems like yours. I look under the dash for after market alarms and remote starts. I would tell you up front, That system has to go. 99.5% of the time, when I take them out and fix the wiring. The cars starts and has no problems. The best alarm systems last 5 to 7 years. Cheap ones, your lucky to get a year out of them. Like I said, when I see them, they have to go before I do anything else.

Jul 28, 2016 | Ford Cars & Trucks

1 Answer

How do I reset my aftermarket alarm it's a viper alarm model 7284V the battery died in the key fob so I took them out and the buttons got pushed so it decoded itself And my wife some how got the alarm


Put new batteries into the fob.
Switch the ignition on and off several times.

Then leave the ignition switched on for 5 minutes.

The fob may well reprogram itself

Feb 17, 2016 | Cars & Trucks

1 Answer

How do i disarm cobra 7910 car alarm


Try getting in touch with the factory. You are not the only person who has encountered this problem.

Feb 07, 2015 | 1998 Ford Escort

1 Answer

I have an 05 Outlander with a post manufacture cobra car alarm. Both of my fobs have stopped working - at same time! Immobiliser still works but cannot put alarm on. I am having to lock the car with the...


When both stop working in the same time, you should not look at the fobs, but to the receiver or the logic in the alarm system in the first place. Like if two key don't fit in the lock, anymore, the keys did not change, but the lock.
But perhaps you should ask a tech to solve this problem. To diagnose this one is a bit difficult not being on the car myself.

Jan 14, 2015 | Cars & Trucks

1 Answer

I have a 99.5 tdi jetta a night ago I locked the car with the key fob which armed the anti theft system now my key fob does not work and will not disarm my anti theft I can get in the vehicle and...


check key fob for stuck button. unhook battery in car to reset alarm. If it has a battery backup on alarm you may need to unhook it to reset the alarm.

Jan 31, 2018 | Cars & Trucks

1 Answer

Where do i find alarm module on a 1997 bmw 318i e36, its a cobra alarm?????


Where ever they mounted it, hard to say. Get under the dash on the drivers side and look for black box that looks out of place.

Jun 14, 2012 | Cars & Trucks

1 Answer

1999 Toyota Avalon, key fob locks doors, but will not unlock. When open door w/key alarm goes off and won't shut off until car started. Sometimes key fob trunk release works, but sometimes not. Alarm...


Hi,
Kindly submit the question under 1999 Toyota Avalon section on the website by clicking this link so that the best car experts can view and post a solution to the problem.

Thanks for using FixYa.

Sep 30, 2010 | 1999 Toyota Avalon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15427 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...