Question about 2003 Audi TT

Open Question

Radio fix fof audi tt 2003

Need to replace stock radio have new one but sumone has cut plug off Audis wiring harness so need to match coulers up

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
marsrover
  • 682 Answers

SOURCE: Audi Concert problem

you must check wiring cable of left speaker-reconnect antenna cable and check if it is firmly connected and apply contact cleaner over faders.

Posted on May 18, 2008

Ad
IFIXALL
  • 868 Answers

SOURCE: radio stuck in safe mode

Turn on radio - the word SAFE will appear in the display. Press th P.SCAN and RBDS buttons simultaneously and hold them down until "1000" lights up in the display.Release buttons.Do not, under no circumtances, continue holding them down or press them once again. This will cause the radio to consider the number 1000 to be the input code.Use station buttons 1,2,3,and 4 to enter the code number on your Radio Card. Use the button 1 to enter the first number 2 for the second number 3 for the third number and 4 for the last number.Once you have entered the code and it shows on the display,press the P.SCAN and RBDS buttons down again simultaneously and hold them down until the word SAFE appears in the display.Release buttons. Soon afterwards a frequency will be displayed.
PLEASE RATE THIS !!!

Posted on Jun 11, 2008

  • 1 Answer

SOURCE: 2001 Audi A6 how to bypass the original amp

Hi there,

The stock amp (mounted inside the sub enclosure) found on the RHS of the boot behind the pull out pannel has a red plug with 8 twisted pairs of wires and 3 other wires (pos, acc and earth).

Out of the twisted pairs you will have

RHS Rear Speaker: Blue/Gray +, Gray/Blue -
LHS Rear Speaker: Red/Gray +, Gray/Red -

You will also have a pair of White/Blue and Brown/White which is the RHS input and a White/Red Brown/White pair for the LHS input. Although... the stock amp uses a common earth input as you will see, the two Brown/White wires going into the same plug.

To put in another amp, you will need one with 'high level' input. Make sure it can take a common ground type input. If it cannot then just use a "high level to RCA" converter.

If you are putting in an after market headunit like i did, then you will just need to separate the two brown/white wires at both ends. If you do this you will need to test which brown/white wire at the head unit end is paired with which wire at the amp end. They are twisted together at the amp end but not at the headunit end (unless you cut the cloth tape back far enough).

Posted on Jan 08, 2009

  • 1118 Answers

SOURCE: Very poor FM radio reception

I would try a CB radio shop at a truck stop, they will have what you are looking for.

Posted on Jan 31, 2009

  • 6 Answers

SOURCE: How do you change the tail light in a 2003 Audi TT?

There is a flap in the boot that you need to flip open. Once opened, there are two screws with really big round ends as big as 1.5 - 2 centimeters in diameter. One is black on the lower end of the light and the other is white which is on the upper end of the lamp. You may need a tourch to see them better, however you can not miss them. Unscrew them with your fingers by twisting these anti clockwise. You need to hold the lamp as as soon as these 2 screws are released, the lamp will then be held by a wire connector which you can remove. You then need a star head screw driver to open 2 screws which will allow you to remove the bulbs that are deffective and have them replaced. Then just retrace your steps.

Posted on Aug 17, 2009

Testimonial: "Thank you. I thought the knobs you mentioned were the ones I needed to turn but they were so unlike any other securing device I wanted to be certain."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I find transmission pressure valve 2003 Audi ?


Go to Audis online site, then to parts. There will be a schematics available for the transmission parts and location

Aug 29, 2014 | 2003 Audi TT

1 Answer

Color codes for stereo


They make kits just for this. Just plugs into the existing harness and then you run you wires to the wires from that harness, some may even have matching plugs that go directly to the Head units wire harness plug. I did My Mustang by cutting into the wire Harness and simply used a multimeter to check for battery, memory 12 volts and running light or dash board Illumination wires then you can test the wires coming out from the stock radio to see which are right, left , front, rear, antenna out, etc..

I just labeled them with magic marker on some masking tape with what they were before I cut off the harness permanently.

Jan 23, 2014 | 1999 Ford Contour

1 Answer

Audi tt 2003 radio fix


Go to Autoleads website and look for your car and the radio you intend to fit. They will sell you an adaptor that will allow you to fit a new radio without wrecking the car wiring.

Jul 28, 2013 | Cars & Trucks

1 Answer

How to connect a Hyundai car radio to my Toyota ute


This is most likely impossible if either is a late model vehicle. As far as wiring you will need to cut the factory Radio harness out of the Hyundai, you will also need a wire diagram for the Hyundai. You will need to buy a harness designed to install an aftermarket head unit into the Toyota, the new harness will come with a description of which wires perform what function. You will then need to match these to the wires on the harness cut from the Hyundai using the diagram. Even if you do all this other hyundai radio will not bolt in where the factory Toyota radio was, and there is no adapter made for something like this. I would suggest just buying an aftermarket stereo. It will be MUCH easier and will almost definitely sound better than a stock Hyundai unit.

Mar 11, 2011 | 2002 Hyundai Accent

1 Answer

Need wiring guide for replacing stock radio 1996 ford windstar with Dual Model XD 1222 radio have harness still need wiring assistance


I would get an adapter harness that will plug into your existing vehicle plug, and the wires are color coded to match up to most aftermarket stereos. You could check e-Bay, or a local automotive audio store for the adapter harness.

May 10, 2010 | 1996 Ford Windstar

2 Answers

I want to change my original cd player for a pioneer


This is because you need to purchase the aftermarket-oem harness plug.This harness plugs into your original equipment radio harness and allows you to plug any aftermarket radio into the stock deck wires.After you plug the harness in you can then connect the radio wires together.Your local autoparts store or circuit city or best buy or audio express will have these radio conversion plugs.I hope I could help

Dec 24, 2009 | 2003 Ford Explorer

1 Answer

My radio on my audi tt does not work at all, i have been in Australia for 6 weeks and when i came back the battery was dead. I have read about the safe mode but the screen is just blank. Any Ideas?


Get a new radio. You probably have a short. Plus the Audis built in alarm sucks some pretty serious juice so that could be what killed the battery. Hard to say without having some diagnostics run.

Sep 18, 2009 | 2002 Audi TT

1 Answer

My factory radio went out in my car...so i had a new one put it in. After the guy installed the radio we noticed that my park lights and dash lights werent working. We checked the fuses and they were all...


I really hope that this guy bought a wiring kit to put in the aftermarket radio, because this could be simple. Your stock radio runs the dash and parking lights threw it's display and that needs to be looped with the new radio. On the aftermarket, there is a orange wire that does this. Since the stock wiring is different with every make and model of auto out there, you need to buy the wiring kit that plugs into the car's harness and matches in color to the harness of the new radio. Putting together the orange wires will give you back your lights. If this person cut the orginal plugs off of the car and wired it direct to the car, you may want to see if the plugs can be put back on and the wiring kit installed or you going to be going through a nightmare of figuring out what wire is what on the car side. Those wiring kits that plug into the car and wire up to the radio are cheap and can be bought at Wal Mart for about 20 to 25 dollars. Good luck

Aug 09, 2009 | 1999 Honda Accord

2 Answers

Indicators not flashing on Audi TT


i believe the audi uses two relays for the turn signals and hazzard lights so it would appear the turn relay has failed. it should be located under the dash near the steer column.... seems to me me they have some shielding under the dash so it may be hard to get to.

May 23, 2009 | 2002 Audi TT

Not finding what you are looking for?
2003 Audi TT Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76691 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14381 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...