Question about Cars & Trucks

Open Question

02 mountaineer transfer case vent hose location

I found the vent nipple on the transfer case cant figure where it goes

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
losflip
  • 94 Answers

SOURCE: ive got an 96 jeep

That is the vent hose for the front axel diff. it attaches to frame crossmember above axel, it dosnt plug on to anything, it is an open vent.

Posted on Dec 06, 2008

Ad
  • 47 Answers

SOURCE: where is the vacuum switch

The switches are a very common problem on the S series. It screws into the top of the transfer case. The easiest way to reach it is going up next to the front drive shaft. There should be 3 vacuum lines going to it that attach in a single rubber plug onto the switch. Hope this helps.

Posted on Jan 08, 2009

BCally1
  • 133 Answers

SOURCE: 1995 dodge ram 1500 4wd, vacuum line

you sure its not the breather tube for the t-case. about 3/8 hose if it is. the vacuum lines for the 4x4 are small plastic lines. red, blue, yellow, etc. think there are four of them

Posted on Jan 10, 2009

  • 25 Answers

SOURCE: 87 samuria tansfercase problem

It doesnt need rebuilding. The shifter sheet that the gear shifter sits on is worn out or not even there which allows the shifter not to operate properly.

You can order a poly one from vendors like Lowrangeoffroad, Trail Tough, Petroworks, and some others.

Posted on Mar 17, 2009

  • 186 Answers

SOURCE: not sure where 4WD vacuum hoses hook up at

Isn't that an electronic motor on the case? If so then it's just a vent for the T-case. If not then it would go to a round ball canister on the fender.

Posted on Aug 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is transmission vent tube for 1996 chevy K1500 - suspect it is clogged but cant find it


vent from trans comes out of trans on the passenger side of the trans.it is located about 1/3 the way back on top of the trans.a rubber hose will be attached and usually connects with the transfer case vent hose.If the trans overheated chances are there is a problem with the transmission.if the fluid smells burnt you have bigger issues.

Mar 09, 2014 | 1996 Chevrolet K1500

1 Answer

Location of top autotrans modulator hose to inlet manifold 1.6 16v injected suzuki vitara 1995


16v. G16B motor, that is easy, must be 3sp A/t as 4sp has non.
the modulator is at the read of the 3sp, and has hard line forward
follow that and it goes to rubber line near the plenum nipple.
hard vacuum nipple.

1: the nipple with no hose. in the engine plenum.
the 16v goes way lean with this nipple empty. at idle.
is this a 3 speed or are you reading online advice for 3sp and yours is a 4speed, (apples and oranges, diffr)
see this page for photos.
http://www.fixkick.com/slush-pump.html

Apr 06, 2013 | 1995 Suzuki Vitara

1 Answer

Small green part on back of air intake 97 camry? what is it called?


Go to any GM dealers parts dept and ask them to show you a exploded diagrams of the area where the part is located then there can ID the part for you.

Jul 23, 2012 | 1997 Toyota Camry

1 Answer

I have a 1997 4wd Chevy S10 4.3 L I need to know where the 3 vacuum hoses from the transfer case go to. One of them is disconnected and I cant find where it goes. This hose is located on the right rear of...


There is a vent hose for air pressure build up that gets vented out so that pressure build up in the T-case does not encourage oil to leak from seals..

Dec 19, 2017 | Chevrolet S 10 Cars & Trucks

1 Answer

The vent hose on my 1990 k1500 is disconnected from the engine side, and i cannot figure out where is came from. I can follow the hose from the transfer case all the way to the engine bay. I haven't been...


IF YOU DONT SEE EMISSION EVAP LABEL UNDER THE HOOD.THE DEALERSHIP PARTS DEPARTMENT SALES PERSON CAN LOOK IN THE COMPUTER HELP YOU LOCATE WHERE VACUUM LINE GOES. VACUUM LINE.PROBABLY GOES TO TRANSFER CASE VACUUM CONTROL TO SHIFT MOTOR.

Dec 24, 2010 | Chevrolet 1500 Cars & Trucks

1 Answer

I need the diagram of a transfer case for a 98 chevy tahoe or i need to know where the hose that hooks on top of transfer case goes to and what it hooks to


Believe there is a vent line on the case,if the hose you are talking about goes right thru the case,it is probably the vent.
Should be open.

Oct 05, 2010 | 1998 Chevrolet Tahoe

1 Answer

FOUR WHEEL DRIVE DOSENT WORK VACUME LINE BROKE BUT CANT FIND WHERE IT GOES


the hose should be a vent to the axle, the axle should be live all the time and power is transfered by the transfer case, the 4x4 function is controled by an electric motor on the case, I would check fuses, but after that I woould recommend a shop look at it!

Apr 08, 2010 | 1999 Ford Explorer

2 Answers

Not sure where 4WD vacuum hoses hook up at


That hose is just a breather hose to vent the pressure inside the transfer case.

Aug 02, 2009 | 1997 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...