Question about Toyota Dyna

Open Question

Toyota dyna bu61 wont turn off

I cant turn my truck off without stalling it and when I let the handbrake off it has a buzzer that just beeeeeeeeeeeeeeeeeps until I pull the handbrake back on again???

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

PyroPCMan
  • 405 Answers

SOURCE: running problem after warming up.

Good Day,

That could be caused by the TPS(throttle position sensor), or MAP(manifold absolute pressure sensor), is yout check engine light on? If it is it probably a sensor. If not it could timing, a vaccuum leak, or other possibilty's. What size motor? The 4.3L or 5.7L?

Let me know I can try to assist further.

Posted on Jul 02, 2008

warlock61
  • 659 Answers

SOURCE: 99 f250 stalled and won't start

could be a bad injector driver module

Posted on Nov 22, 2008

  • 580 Answers

SOURCE: bmw 325i 2003 stall

Sounds like you have a small bit of dirt or grit in the fuel system when accelerating it is drawn with enough force to cut off the fuel supply then is released when engine at Idle.
1 run liquid fuel line/injector cleaner in 1 tank
2 check fuel lines for debris
3 change fuel filters
4 have fuel tank flushed
here is trouble shooting order less expense to greater.

Posted on Aug 23, 2009

joevanek
  • 19 Answers

SOURCE: 86 ford f250 the truck wants to stall when warmed

I had a truck that acted similar and it turned out being the coil! It ran fine on idle but once it warmed up it missed and had trouble starting. Good Luck!!

Posted on Mar 17, 2010

SOURCE: 1989 Cutlass Ciera. Got gas about 30 minutes prior

You may have gotten some condensational moisture in your gas. It collects on the insides of tanks when high humidity occures. The easiest way to rid your tank of water is to put in a bottle of alcohol (91%.) This will disperse the water, and as a consequence increase your octane level a bit. It will never harm your engine or fuel system. Do this first, and wait an hour. Charge your battery if it is low, as you are going to have to push all the contaminated gas through the fuel system before it can start. Try a gasoline with 10% ethenol (alcohol), it rarely if ever has water present.

Posted on Apr 07, 2010

Testimonial: "Quick and thorough response...thank you."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why don't the headlights work properly on my Toyota Dyna BU61?


From description sounds like dimmer switch has failed.

Mar 29, 2015 | Toyota Cars & Trucks

2 Answers

Toyota 2005 hand brake not working


Is the hand brake really easy to pull??? You may have to adjust your hand brake cable. I found a video on how to adjust the cable.
Hope this is helpful :-)

-Scott Handbrake Adjust Toyota Corolla

Feb 14, 2015 | Toyota Camry Cars & Trucks

1 Answer

Where is the fuse for the air brakes in a toyota dyna 1995


Hi Ashwin, We have worked on several Dyna's but none with air brakes? If you're asking something about the servo assisted braking system, the only fuse I know of is for the brake lights. The braking system of the Dyna usually has vacuum operated servo assistance brakes. the vacuum pump is mounted onto the alternator, sometimes in front and sometimes behind, depending upon the year of manufacture and the engine in use. There is a pressure warning switch fitted to a reservoir tank to warn if there is a leakage and low pressure is not maintained. Operation sounds a buzzer inside the cabin. If this info is of no use please send a much more detailed question and the reason for searching the fuse? Regards John

Jun 07, 2014 | 2005 Chevrolet Malibu

1 Answer

Toyota dyna 1985 model


if you cant turn off ignition. more likely ignition switch broken..

Jul 29, 2013 | Cars & Trucks

2 Answers

Handbrake adjustment on a toyota corolla 1986


you need to take out the tire see if your drum had a hole or take out your drum adjust the adjuster until you rich the correct adjusment

Sep 06, 2012 | Toyota Cars & Trucks

1 Answer

Toyota dyna oil light reset


After changing the oil and filter on a 2008 Dyna, the "oil change" light would not turn off. On the plastic dash screen, there is a small circular rubber plug just above the rev counter. This plug can be prised off. Prise off the plug, insert a pin and press the button. Oil change light turns off.

Jul 14, 2012 | Toyota Cars & Trucks

1 Answer

I cant hear the buzzer when opening a door or before engine start on my nissan sentra 2002 se-r spec v


good for you its a dammed noise i can do without ,in the fuse board or behind it is a relay looking buzzer and i always rip them out and hit them with a hammer ,dammed annoying things ,makes a car sound just like a yanky piece or metal with all these buzzey things to drive me up the wall ,its bad enough with er indoors without this erksome noise as well

Jun 06, 2012 | Nissan Sentra Cars & Trucks

2 Answers

My handbrake needs adjusting in my Toyota Corolla 1994. Can u please explain how this adjustment is done.


Hello, My usual Brands are Ford products, but Foreign cars usually use simple, less expensive ways to do things. Assuming the brake pads are good, there should be a cable connected to the handbrake. You would usually pull the handbrake up to engage about 1/4 the way to engagement and lock it there.
Then you would go underneath the car and find the cable that stretches from the handbrake lever to a juction with a second cable. There should be an adjusting thread somewhere at this intersection.

With the rear wheels off the ground, you would tighten the nut on the threads of the handbrake cable until you hear rubbing in the rear brakes. Then get inside the car and pull back on the handbrake lever and you should not be able to move the rear wheels with the handbrake set. You then release the handbrake 100% and the rear wheels should turn mostly without noise.

Now if you can not find an adjustment nut under the car, it is possible the handbrake adjustment nut is under the handbrake cover/boot inside the car. Still use the same process of setting the lever 1/4 engaged and tightening the threaded cable until the rear wheels start dragging.

I hope this helps you.

Sep 28, 2011 | 1994 Toyota Corolla

1 Answer

2005 Toyota Corolla problem. My Corolla buzzer comes on when my driver door opens. Also the lights are still on and wont turn off.


the buzzer is coming on because the lights are still on. the car is warning you of this. lights staying on may be a bad sensor or bad light switch.

Oct 01, 2009 | 2005 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...