Question about Volvo 940

Open Question

Torque settings head bolts

I have a 1992 Volvo 940GL, I'm looking for the cylinder bolt torque settings. I have the non-turbo engin

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

HellPoolHall
  • 74 Answers

SOURCE: torque to apply to cylinder head bolts and camshaft bolts

Autozone.com usually has these specifications.

Posted on Aug 07, 2008

  • 1 Answer

SOURCE: Angle Torque settings head bolts

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Posted on Mar 17, 2009

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

  • 1 Answer

SOURCE: torque setting cylinder head bolt 4 cylinder KIA sportage

I need the torque settings and pattern for a Kia Sportage 2.2

Posted on Jan 28, 2010

steve_e_uk
  • 1675 Answers

SOURCE: golf iv 1.6 8v cylinder head torque settings

hi to tighten you have to do it in 4 stages as follows
1st stage 40nm leave 5 mins 2nd stage 60nm leave 5 mins 3rd stage 90 degrees leave 10 mins 4th stage 90 degrees then you are done i will try put order on here i hope this works as follows
10 4 2 6 8 front of engine back of engine 7 5 1 3 9

in that order hope this helps

Posted on May 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Head torque specification for l200 4d56 DID DOHC 2007


what car? and year>? and country , so we can look it up in our
great online sources. (all 3 must be known)
in the USA we use alldata.com (or the dealer FSM)

i guess you dont know that some heads are not torqued, or use TTY bolts, right? some are set by ANGLE degree.
that is covered in the FSM all that. the facts.
most head failures result from guessing.
or asking here, with no facts on car.
some engine run different heads, and different if turbo.

case in point, all this Mitsubishi engines

my guess
Mitsubishi Triton

Oct 24, 2014 | Cars & Trucks

1 Answer

CYLINDER HEAD TORQUE


First off you need new bolts as they are one time use stretch to yield bolts.
Step 1 - 20nm , step 2 - 60nm then 130 degrees of bolt head rotation*.

Feb 01, 2014 | 1992 Volvo 960

1 Answer

Cylinder head torque specs on a 2000 volvo s70 2.4 Liter


you have torque cylinder head bolts in 3 steps first torque bolts 14 ft lbs then second torque all bolts to 43 ft lbs step three torque all cylinder bolts to plus 90 degrees.

Nov 15, 2012 | 2000 Volvo S40

1 Answer

1992 vw jetta 1.6 turbo diesel,what is the cylinder head bolt torque spec?


!st thing is get the revised head gasket (used on 1993 up) for this engine from VW or Felpro, always use new head bolts or a repeat failure will occur. Using the revised head gasket here is the procedure to torque the head down, it is done in stages. PLease go to this site and read the whole procedure.

Feb 07, 2012 | 1992 Volkswagen Jetta

1 Answer

What is the torque on the head bolts and sequence on a 760 volvo 2.3 turbo


The head torquing sequence for any cylinder head is as below, continue the pattern if there are more than 10 bolts:-


10 6 1 3 7

8 4 2 5 9

Start at the middle two bolts and do your sequence at least three times, first at about half the torque, then the full torque value at least twice. It is good practice to re torque the head again after about 1000 km (600 miles), but this is often disregarded due to the problems of getting to the head bolts.

Jan 29, 2011 | 1988 Volvo 760

2 Answers

How to torque engine heads,rod bearings and main bearing by foot pound?


cylinder head bolt torque for a DOHC Turbo 3.0L V6

92 ft lbs.

cylinder head bolt torque for a Non-Turbo

76-83 ft lbs.

main bearing caps

mark on head of bolt "9" 59 ft lbs.

mark on head of bolt "10" 70 ft lbs.

connecting rod nut 38 ft lbs.

Sep 07, 2010 | 1992 Mitsubishi 3000GT

1 Answer

Head bolt tourqe settings on a toyota cressida


Cylinder head bolt removal sequence


Removal sequence: Front 3 7 11 13 10 6 2 1 5 9 14 12 8 4

***CAUTION*** The above sequence must be followed during removal as to avoid warpage of the cylinder head unit

Reverse sequence to install, Step 1: Torque to 10 Ft/Lbs Step 2: Torque to 18 Ft/Lbs Step 3: Torque to 25 Ft/Lbs Step 4: Turn an additional 90 degrees Step 5: Turn an additional 90 degrees Step 6: Torque the 2 recessed 8mm bolts to 13 Ft/Lbs *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper Torque

Don't forget to rate this answer, Good Luck

Apr 24, 2010 | 1992 Toyota Cressida

2 Answers

How much lb ft. of torque should i put on the cylinder head bolts of a 1992 toyota hilux surf turbo diesel 2lt engine.


what is the valve clearance and cylinder head torque for toyota 2lt diesel engine

kasim

Jan 25, 2010 | 1992 Toyota 4Runner

1 Answer

Head bolt touqe settings


Tightening torques

Do not reuse the bolts as they may be stretched.

Cylinder head to engine block
Stage 1: 32Ft-lbs
Stage 2: +90degrees
Stage 3: +90degrees

Cylinder head to lower timing
chain cover: 89in-lbs

Nov 27, 2008 | 1992 BMW 3 Series

2 Answers

95 volvo 940 running rough


Have you checked compression on non firing cylinders? Likely has blown head gasket between these two cylinders if located side by side.

Jun 24, 2008 | 1995 Volvo 940

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...