Question about 2005 Chrysler 300

Open Question

Fcm front I have a 2005 Chrysler 300 unit will not crank I checked relays found ok if I jump the starter relay unit will crank but won't start with key on the run position checked signal from ignition switch to starter relay and there is none, those the Fcm control this signal or those the ECM control it?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bunnydawg
  • 5158 Answers

SOURCE: I went out to warm

First unhook the battery for about a half hour to reset the computer.
does that have anti-theft on it.
a remote starter ?
second either swap the relays for the starter and fuel pump or replace them outright.
when you bypass the relay to get it to crank... will it start ?

Robert

if that radio is of the anti-theft variety make sure you know the code and how to enter it

Posted on Dec 25, 2009

  • 1584 Answers

SOURCE: 94 Chrysler Town and Country won't start with key.

has it got an immobiliser / if so there is a fault there. If not an ignition switch itself.

Posted on Apr 07, 2010

  • 610 Answers

SOURCE: looking for the relay for

THERE IS A WIPER HIGH/LOW RELAY, AND A WIPER ON/ OFF RELAY. BOTH ARE LOCATED IN THE INTEGRATED POWER MODULE, RIGHT FRONT OF ENGINE COMPARTMENT. RELAY ID SHOULD BE PRINTED ON THE INSIDE OF THE COVER. GOOD LUCK!

Posted on Dec 22, 2010

  • 1 Answer

SOURCE: 2003 chrysler voyager wont start and has no spark

Van was running fine,just lost power and just has the sound of trying to turnover but will not start.

Posted on Jun 20, 2011

  • 116 Answers

SOURCE: 2002 Chrysler Town and Country,

Either the switch is broke or the blower motor is. My guess would be the blower motor. You will have to check the plug at the blower motor for power with an ohm meter. And if it does move the switch to see if it put's out more amps. If it does it's the blower motor. If it doesn't it's the switch.

Posted on Jun 29, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Chrysler 300 3.5 engine will not start ? WILL JUST CLICK BUT WILL NOT START GOT $7e8 ; $7e9 CODE BUT NOT SUB MENUS ?


CODES $7e8 & $7e9 ? P0xxx example. What clicks ? starter solenoid ? Relay ? etc.... Do a starter system voltage drop test ,go to youtube an check out no crank - no start videos . Also check out voltage drop testing starting system .

Dec 31, 2015 | 2005 Chrysler 300

1 Answer

Wont start the starter is working yet it won crank what can I do


Did you check power an grounds using voltage drop testing , did you check battery voltage an computer control at the starter motor relay in the under hood fuse / relay box ? Instead of guessing you need to learn how to use a DVOM - digital volt ohm meter an test ! The powertrain control module controls the starter motor operation ! Starter Voltage Drop VEHICLE RELAYS Operation Diagnosis ,If you pull the relay an jump pin's 30 & 87 the starter should crank ,test the circuit starter motor side ! Pins 85 & 86 are the control side ., Pin 85 or 86 forget which one has battery voltage with the key on . The one with out voltage is control from the engine computer ! Also if the anti theft system is active it wont start !

Aug 25, 2015 | 2005 Chrysler Pacifica

4 Answers

Chrysler 300 2006 started and died 4 times and now won't do anything. Not even a click. Have battery power to everything else


Try boosting it. If it starts and keeps running with a boost, but dies soon after you remove the boost, the battery is bad.

Feb 07, 2015 | 2006 Chrysler 300

1 Answer

2005 chrysler 300 has power but says nothing all you hear is a click


If is not cranking,check your starter motor if is get power. if no check that ignition again for loose connection, check relays. Or else your starter need repair

Sep 30, 2014 | 2005 Chrysler 300

1 Answer

2005 PT Cruiser no crank


sounds like the crank position sensor. check continuity and 5volts reference at sensor. you can have it checked by someone with a Good scanner(SNAP-ON). If it happens to start up,drive the car till it wont start up again; unplug the crank position sensor and count to 5 then plug it back in. If it starts then its the crank sensor.(just a quick way to test it and get you home or to a shop)

Jan 01, 2014 | 2005 Chrysler PT Cruiser

1 Answer

Car won't start


U might have 12 volts but no cranking amps try a jump start

Sep 20, 2012 | 2005 Chrysler Sebring Conv

2 Answers

2005 Altima won't start, hear clicking sound coming from fuse box,key stuck in ingintion,won;t turn over,tried to jump start.


the clicking that you hear is coming from the starter relay. sounds like your ignition starter switch or ignition lock cylinder is bad.

May 30, 2012 | 2005 Nissan Altima

1 Answer

Won't start


So it's a no crank condition? Do dash lights, gauges, and everything else work when the car won't crank over? If so, buy a cheap $5.00 testlight, and when the car won't crank, pull the small black wire off the starter solenoid. While someone holds the key in start (cranking) position and clutch pedal depressed, see if the black wire has power as it should. (Ground the testlight and just touch the wire's end terminal. If powered, the testlight will light up.) If power there, then the starter solenoid is failing. Toyota starters are very good units, but the solenoid's internal contacts get old and pitted.
If no power at the black wire, then the start circuit from ignition switch to clutch safety switch (on the clutch pedal) to starter relay to starter solenoid will have to be diagnosed. To double-check: take a single battery jumper cable and put it on the positive battery post connection. Put the other end of the jumper cable on the solenoid terminal where black wire was removed. Key can be off. Make sure car is in neutral, brake set. If starter now operates, solenoid is O.K., and it is a problem in the start circuit, -ignition switch, neutral start switch, or in the wiring.
Now find a grounding place for testlight under the dash. When car won't crank, check for power coming out of ignition switch on the black wire with white stripe. This is the start wire for the starter solenoid. Key must be in crank position. Wire shoud be powered-ignition switch is working. If no power, switch is failing. You can do the same for the clutch start switch-it's a simple switch, that when clutch is depressed switch is closed and passes power on from ignition switch to the starter relay (thus allowing power to the starter solenoid). Black wire, red stripe-this is wire from clutch switch to starter relay. When key is in crank, clutch depressed, this wire should be hot.
With me so far? Still haven't found a problem, or any loose connections? Next and last is the starter relay. It is located under dash, close to gas pedal, but under the center console, just forward and left of gear shifter. It can be tested and the wiring diagnosed there, but relays are cheap, so just swap in another and see if that helps.
If you have tried everything, and still no help, you could try a new wire from the relay to the starter solenoid. This is that black wire we started with. Older toyotas sometimes have a problem with degraded wiring not passing enough current to operate the starter

May 04, 2012 | 1992 Toyota Tercel

1 Answer

2005 pt cruiser won't start won't crank, everything works


When you turn the key on the ASD relay should turn on the fuel pump and power the injector, Do this lets cheat the system go to the ASD rely open the cover expose the inside have some one turn the key on does the ASD make contact? If not turn the key on collpase the ASD so it make contact do you hear the fuel pump come on? Now try this just as how you iopen the ASD do the same to the starter relay. Put the car in gear e brake on someone in the vehicle in case the car start and you are in front of it and it runs you over so at least they step on the brakes. Key on ASD exposed as your collapse the starter relay does the ASD relay turn on? Here why if you can control all the relay from under the hood you will need a ignition switch (the eletrical part)

Feb 22, 2012 | 2005 Chrysler PT Cruiser

Not finding what you are looking for?
2005 Chrysler 300 Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...