Question about Mazda MAZDA6

Open Question

Replace microswitch drivers door doesn't lock or unlock electrically..ve to do it manually

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2003 Civic left Side Electric Door lock Broken

bye a diff car hondas are nothing but problems

Posted on Feb 10, 2009

Ad
ghost4548
  • 776 Answers

SOURCE: electric door lock mafunction

Door lock/unlock actuator (motor) has gone bad in the passenger side. Get the actuator from a Hyundai Parts dealer (or junk yard if you trust them) and replace it yourself OR take it to a Hyundai Service Center and they'll do it for you.

Posted on May 31, 2009

  • 1 Answer

SOURCE: Electric windows not working,central locking locks

Problem was caused by a broken wire inside drivers door panel.

Posted on Feb 16, 2010

  • 14036 Answers

SOURCE: replaced batery in key fob

reprogram the remote transmitter. first leave driver door open all other doors closed,key removed from the ignition switch. insert key into the ignition switch,then remove it.press lock and unlock on the vechicle door lock control switch at 1 second intervals 5 times. close and repoen drivers door.press lock and unlock on the vechicle lock control switch at 1 second intervals 5 times. insert key into ignition switch. switch ignition on and off twice to program a remote transmitter code whilst erasing the original codes or three timre to check how many remote transmitters are currently registered.remove key from the ignition switch.system should now lock and unlock.twice to indicate programming mode or one to four times,slowly to indicate number of remote transmitters registered.for the solara press and hold lock and unlock remote buttons together, press lock remote button for a second period of 1 second. system should now lock and unlock vechicle.once to confirm, twice to indicate registration has failed.if required repeat button procedure to program remaining remote transmitters.note to exit programming mode close drivers door or insert ignition key.maximum of 4 remote transmitters can be programmed.if akk failed let dealership reprogram remote transmitters.

Posted on May 18, 2011

  • 3 Answers

SOURCE: My 2000 Buick LeSabre Custom driver's door is

try graphite

Posted on Jun 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power door lock - can't use key to unlock door


need to remove the door panel and check the clips that connect to the locking rods possiblr damaged or disconnected

May 11, 2013 | Buick Regal Cars & Trucks

1 Answer

2000 cadillac deville driver side won't open with the key


1) Key turns but dose not unlock door. This means that the rod that goes to the back of the lock has came off. This also means that is the reason door is not unlocking with the remote as it pops the lock rod inside the door which pushes the lock open.
2) Key does not turn lock at all but works passengers side door. This means that the locks has been changed in the door, but that doesn't sound like the problem as you say the remote doesn't open the drivers side door so more than likely the rod has came off the back of the lock

Nov 07, 2012 | Cars & Trucks

1 Answer

The driver side electric door panel doesn't work on my '06 Chevy.


Gonna need to remove the panels and see where you left some wiring disconnected or pinched.

Oct 30, 2012 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

My alarm system isn't working


The power door lock electric actuator motor is defective most likely. You will need to pull the door panel off and test it with a volt meter for power and ground when the power locks are actuated, if the system is powering up the lock motor but it doesn't move the rod then replace it,.

Oct 10, 2012 | 2008 Honda Accord

1 Answer

My key fob for my 2006 LaCrosse unlocks the doors & opens the trunk, but doesn't lock the doors. Can it be cleaned, or does it need to be replaced?


It is not clear whether the problem is with the fob or the receiver in the car. You could try replacing the fob (they are available online from various sites) but the receiver will need to be programmed to use it, and that usually requires a trip to a dealership (unless you have access to the OEM service manual). Your best bet is to take it to a dealership and have them diagnose and repair the problem.

Jul 05, 2017 | Cars & Trucks

1 Answer

Power door locks do not operate properly. When I have the engine running, then put it in gear, the doors lock electrically.After shutting the engine off, the power door locks do not unlock any of the...


I've heard it can be done with some difficulty. You'll probably have to remove your rear seats, or at least the bottom seat portion, to get the inside panel off. Usually, the easy fix for troublesome door locks is a good cleaning, and a little light oiling. That one on the rear should be checked for operation when you get to it.

Oct 20, 2011 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Similar electrical issues with driver's side door controls. Power locks, power window, and power mirror on driver's side are not functioning. I can manually unlock the door, but the buttons on...


CHECK FUSES FOR POWER WINDOW,CHECK FUSE FOR POWER MIRROR AND CHECK FUSE FOR POWER DOOR LOCK.IF FUSE OKAY DOOR CONTROL MODULE FAULTY ITSELF.

Sep 11, 2011 | 2004 Saab 9-3

1 Answer

Electronic door locks not working


It will be a bad microswitch in the mechanical lock driver's door and because of the microswitches do not get the impulse when other doors to unlock! Unfortunately, this microswitch is part of the lock and can be purchased separately! Only whole lock! ( Nr. 9. is it )5abc095.jpg

Jun 23, 2010 | 2003 BMW 325

1 Answer

Arlarm going off


The Central Electronics module is detecting a fault in on of the door locks. Its not necessary that the lock is faulty, it may just need to be adjusted. To be more specific, the locking knob that goes up when vehicle is unlocked and goes down when locked , is connected via a linkage to a microswitch on the door lock actuator. The microswitch has three positions. top position is unlocked, center is neutral, bottom is locked. However after any cycle of the lock/unlock switch, the microswitch has to return to the neutral position for it function correctly. Most likely your vehicles drivers door lock microswitch does not return to the center/neutral position after you lock you car which causes the alarm to go off. In this case you should have the drivers door lock assembly replaced by a good knowledgeable workshop, and the dealer isnt one of them.

Aug 11, 2008 | 2000 Volvo S80

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...