Question about Cars & Trucks

Open Question

How to replace front wheel bearing on 98 camry

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 24 Answers

SOURCE: replace front wheel bearings

The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

On a scale of 1-10 difficulty, Id rate it a strong 7

Posted on Jun 20, 2008

dennymulford
  • 1055 Answers

SOURCE: wheel bearing change for 98 malibu

you have too change the whole assembly
pull the wheel pull the callipilar pull the callipliar mount pull the rotor pull the half shaft nut then take the three bolts out of the hub assembly and pull it less than hour job !!!!

Posted on Feb 24, 2009

blueextc3221
  • 15935 Answers

SOURCE: replacing front wheel bearing

  1. Loosen the wheel nuts and the center axle nut.
  2. Raise the vehicle and safely support it.
  3. Remove the wheel. Remove the ABS speed sensor if so equipped.
  4. Unclamp the brake hose from the shock absorber, but do not disconnect the line.
  5. Remove the brake caliper and hang it out of the way on a piece of stiff wire. Do not disconnect the brake line; do not allow the caliper to hang by the hose.
  6. Remove the brake disc.
  7. Place a dial indicator near the center of the axle hub, and check the backlash in the bearing shaft direction. Maximum is 0.0020 inch (0.05mm). If the backlash exceeds the maximum, replace the bearing.
    1. Usiung a dial; indicator, check the deviation at the surface of the axle hub outside the hub bolt. Maximum is 0.0028 inch (0.07mm). If the deviation exceeds the maximum, replace the axle hub.
    2. Install the disc and caliper. Tighten to 65 ft. lbs. (88 Nm).
  8. Remove the cotter pin and install the wheel. Lower the vehicle to the ground.
  9. Remove the lock nut cap. While depressing the brake pedal, remove the center axle nut.
  10. Raise and support the vehicle again and remove the wheel, caliper and disc.
  11. Loosen the 2 nuts on the lower side of the shock absorber. Do not remove the 2 nuts and bolts.
  12. Remove the cotter pin and nut from the tie rod end.
  13. Remove the tie rod end from the knuckle using a joint separator or equivalent.
  14. Remove the bolt and 2 nuts holding the bottom of the ball joint to the control arm and separate the arm from the knuckle.
  15. Remove the 2 nuts from the steering knuckle. Place a protective cover or shield over the CV boot on the driveshaft.
  16. Using a plastic mallet, tap the driveshaft free of the hub assembly.
  17. Remove the bolts and remove the axle hub assembly.
    1. Clamp the knuckle in a vise with protected jaws.
    2. Remove the dust deflector. Loosen the nut holding the ball joint to the knuckle. Use a ball joint separator tool or equivalent to loosen and remove the joint
    3. Use a slide hammer/extractor to remove the outer oil seal.
    4. Remove the snapring.
    5. Using a hub puller and pilot tools or equivalents, pull the axle hub from the knuckle.
    6. Remove the brake splash shield (3 bolts).
    7. Use a split plate bearing remover, puller pilot and a shop press, remove the inner bearing race from the hub.
    8. Remove the inner oil seal with the same tools used to remove the outer seal.

    To install:
    1. Place the inner race in the bearing. Support the knuckle and use an axle hub remover with a plastic mallet to drive out the bearing.
    2. Clean and inspect all parts but do not wash or clean the wheel bearing; it cannot be repacked. If the bearing is damaged or noisy, it must be replaced.
    3. Press a new bearing race into the steering knuckle using a bearing driver of the correct size.
    4. Place a new bearing inner race on the hub bearing.
    5. Insert the side lip of a new oil seal into the seal installer and drive the oil seal into the steering knuckle.
    6. Apply multi-purpose grease to the oil seal lip.
    7. Apply sealer to the brake splash shield and install the shield.
    8. Use a hub installer to press the hub into the steering knuckle.
    9. Install a new snapring into the hub.
    10. Using a seal installer of the correct size, install a new outer oil seal into the steering knuckle.
    11. Apply multi-purpose grease to the seal surfaces which will contact the driveshaft.
    12. Support the knuckle and drive in a new dust deflector.
    13. Install the ball joint into the knuckle and tighten the nut to 105 ft. lbs. (142). Install NEW cotter pin.
    14. Temporarily install the hub assembly to the lower control arm and fit the driveaxle into the hub.
    15. Install the knuckle to strut bolts, then attach the tie rod end to the knuckle.
    16. Tighten the strut bracket nuts to 203 ft. lbs. (275 Nm) and tighten the tie rod end nut to 36 ft. lbs. (49 Nm). Install the NEW cotter pin.
    17. Connect the ball joint to the lower control arm and tighten the nuts to 105 ft. lbs. (142 Nm).
    18. Install the brake disc.
    19. Attach the brake caliper to the knuckle and tighten the bolts to 65 ft. lbs. (88 Nm).
    20. Install the center nut and washer on the drive axle.
    21. Install the ABS speed sensor if so equipped. Install the wheel
    22. Lower the car to the ground.
    23. Tighten the wheel nuts to 76 ft. lbs. (103 Nm). Tighten the hub nut while depressing the brake pedal to 137 ft. lbs. (186 Nm) on 1988-91 models and 152 ft. lbs. (206 Nm) on 1992-97 models. Install the cap and cotter pin.
    24. Remove the protective cover from the CV boot. Check front wheel alignment

Posted on Apr 25, 2009

  • 17 Answers

SOURCE: How do you replace front wheel bearing 98 honda

Buy a Hayne's manual and read the instructions.

Posted on Aug 17, 2009

  • 98 Answers

SOURCE: How is front wheel bearing replaced on a 2001 Volvo S40?

most front wheel bearings are pressed in you half to take the whole control arm off pull out the hub press out the bearing grease the new one and press it in its best to take it to a machine shop do not try pressing it in yourself

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram front wheel bearing


It is a Wheel Hub Bearing Assy

Rock Auto.Com --for parts

You replace the entire thing, when it makes a
noise, around 25 to 40 mph & do both sides

On You Tube Video-- there must be 50 or more sites
you can watch on all kinds of vehicles & bearings ,to
get an idea what is involved

Aug 11, 2014 | 2000 Toyota Camry

2 Answers

Size or part number for wheel bearings for toyota camry 94


If you have the bearings out then the number embossed in the face of the bearings is the part number and is good for all brands of bearings . If you do not have the bearings out then go to a bearing shop (cbc,bearing service, timken,skf etc) and they will have the numbers for your vehicle probably in a kit package. half the price of genuine for the same quality.. Just take the model, year , 2 or 4 wd and vin number to match the car with the bearing kit.

Apr 22, 2014 | 1994 Toyota Camry

1 Answer

What type of front wheel bearing for toyota camry DX,1991, v6


It is a fairly large double row bearing on this front wheel drive car, Any auto parts store, or dealer will get you the right part, and they are not something that is easy to replace, I suggest you to please take it to a qualified mechanic as it takes some tools you probably don't have. Hope this helps.

Apr 27, 2010 | 1991 Toyota Camry

1 Answer

How to replace front wheel bearing on a 1999


removal of the spindle, and has to be pressed off and on.

Sep 22, 2009 | 1999 Toyota Camry

1 Answer

My Toyota camry xle 1997 175000miles feels as if the right front wheel "slides" a few inches when i turn right or bear right. Can feel no play in the wheel when I shake it. Any idea what's going on? Thanks


raise the front end off the ground on Jack stands. then try to find play on the wheel. it must be off the ground. I guess it your wheel bearings

Sep 12, 2009 | 1997 Toyota Camry

2 Answers

My camry is making a loud whining noise. I took it to a mechanic and he said it was probably the front bearings. The noise only happens when the wheels are spining. My question is how do I replace these....


Hi there. Most, if not all front wheel bearings these days are pressed into the front wheel hub assembly and to replace these is not normally a DIY job. Because new bearings need to be pressed into the hub assembly, a machine shop press ought to be used and the job undertaken by competent individuals. My advice if you do intend undertaking the work yourself is to remove the hub assembly and then have a machine shop operative remove the old bearings and have the new bearings pressed-in for you. Hope this helps, Scottech.

Jul 02, 2009 | 1996 Toyota Camry

1 Answer

How to change a rear wheel bearing on a 1994 toyota camry


The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

May 30, 2009 | 1994 Toyota Camry

1 Answer

Hi wheel bearing replace


the bearing needs to be pressed in and out

Apr 06, 2009 | 1994 Toyota Camry

1 Answer

Wheel bearing change for 98 malibu


you have too change the whole assembly
pull the wheel pull the callipilar pull the callipliar mount pull the rotor pull the half shaft nut then take the three bolts out of the hub assembly and pull it less than hour job !!!!

Feb 24, 2009 | 1998 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...