Question about 2001 Hyundai Santa Fe

1 Answer

1999 mustang...what is the value of the TPS....

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Http://www.rockauto.com/

Posted on Jul 28, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Free manual for 1999 ford mustang


hello.for download a free manual of ford mustang 1999,you can click here : http://www.motorcraftservice.com/?link=002&urlfile=/pubs/content/~WOXMUS/~MUS~LEN/42/99musog1e.pdf
its a pdf file.use from pdf reader softwares for reading.

Mar 12, 2013 | 1999 Ford Mustang Cobra

1 Answer

P0123 Just put new Tps and it is showing this code now can adjust the TPS?


DTC P0123 - Throttle Position Sensor/Switch A Circuit High Input
This code means that the the car's computer has detected that the TPS (throttle position sensor) is reporting too high a voltage. Were codes deleted after this job? This is a code for TPS voltage high.

The sensor voltage should never be greater than 5volts. It normally reads .5 to .8 volts at idle (closed throttle). The orange and dark blue is the signal wire, black and light blue is the sensor ground, and the violet and white is the 5volt supply wire. You will need to back probe the signal wire to find the value. It is possible the signal or ground wires are open. Or the PCM is faulty.

zjlimited_775.gif


Hope this helps (remember to rating this free answer).

Oct 10, 2011 | 1999 Dodge Ram

1 Answer

If I disconnect the TPS the car will run. Plug it back in it won't run.


tis sounds like the tps is no good and the computer has gone into what is called backup mode were it uses a predetermined set of values already programed in the computer to allow it to run.

Jun 21, 2011 | 1999 Pontiac Grand Am GT

2 Answers

I have a 2001 Ford Mustang, v6 3.8 5 speed manual


The clutch is not fully releasing. You can try putting it into some other gear first, then rapidly moving to first gear, but really, you need to either adjust the clutch, or get it repaired.

Jul 07, 2010 | 2001 Ford Mustang

1 Answer

1999 Mercury Cougar with automatic transmission, car was running fine, then it wanted to shift while driving, and the speedometer dropped to 0, with jerky motions. Same thing 3 years ago and dealer said...


ONe thing to check is that your throttle position sensor (TPS) is working as it should and that the electrical connections to it are clean and tight and that wires associated with it are intact. When your TPS starts misbehaving by sending the wrong position values to the ECU then erratic engine revs and associated difficulty in gear changes follow. TPS is a an electrical sensor mounted on the outside of the throttle body on the end of the throttle plate shaft. As the throttle is opened the shaft rotates. The amount of throttle (shaft rotation) is measured by a contact within the TPS sliding on a carbon track. The TPS has three electrical lines to it. One is at consistent low voltage ('throttle closed' end of the track) the other is about 5 volts ('throttle fully open' end of the track) and the third is the variable sliding contact which sends a voltage corresponding to the throttle position to the ECU. The TPS is pretty easy to check out with a voltmeter and you can read the variable out put by simply turning the throttle shaft by pulling on the accelerator cable. If the TPS needs replacing it is a pretty cheap and easy to do. Hope that helps some

May 21, 2010 | 1999 Mercury Cougar

1 Answer

92 mustang lx with a 2.3 liter, will not go over 35mph


You have a clogged Cat or exhaust system. Car can't breath.

Apr 14, 2010 | 1992 Ford Mustang

1 Answer

Tps a circuit low input stalls when you let foot off gas


The tps needs to be checked,with a ohm meter,unplug the sensor,and check the tps,see what the value is,between the three terminals,and then check the voltage to the sensor with a digital volt meter only,not analog.It should read 5 volts.The ohm reading will vary,but see that it does vary,and not fall in the middle of moving the lever of the tps.If it falls,or has a dead spot,replace the tps,if not,then there is another problem blaming the tps.

Mar 13, 2010 | 1999 Jeep Cherokee

1 Answer

What does fault code PO122


A P0122 code means that the the car's computer has detected that the TPS (throttle position sensor) is reporting too low a voltage. It coud be a bad TPS, or a wire problem.

Oct 28, 2008 | 1997 Ford Mustang Cobra

Not finding what you are looking for?
2001 Hyundai Santa Fe Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...