Question about Cars & Trucks

Open Question

1990 parking brake diagram

The schematic for emergency brake cable for 1990 silverado

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1596 Answers

SOURCE: Park Brake Adjustment


Park Brake Adjustment (Disc Brake)

Tools Required

j 21177-A Drum-to-Brake Shoe Clearance Gage

Park Brake Shoe Adjustment

Caution: Refer to Brake Dust Caution.

Important: The park brake shoes must be adjusted before the park brake cable tension is adjusted.Set the J 21177-A so it contacts the inside diameter of the rotor

  1. Position the J 21177-A over the shoe and the lining at the widest point.
  2. Turn the adjuster nut until the lining just contacts the J 21177-A. Park brake shoe to brake rotor clearance: 0.6604 mm (0.026 in)
  3. Repeat steps 1-3 for the opposite side.
Park Brake Cable Tension Adjustment

Important: Before you adjust the park brake cable tension, verify that the park brake shoes are adjusted to provide a clearance of 0.6604 mm (0.026 in) and the rear disc brake rotors are installed.

  1. Verify the self adjuster lock-out pin has been removed.
  2. Fully apply and release the park brake pedal 3 times.

Posted on Feb 22, 2009

Ad
  • 135 Answers

SOURCE: 2003 silverado HD adjust emergency brake cable?

first you need to check the rear brakes ,the emergency brakes work off the rear brakes, there is an adjustment on the center of cable that goes between both rear brakes,hope this is some help,thanks robert b.

Posted on Jul 06, 2009

  • 1 Answer

SOURCE: emergency break cable broke on 2004 silverado

I had the same problem on my 2003. Open the driver door all the way. Get on your knees just outside the door. Follow the plastic tub that holds the parking brake release cable inside the truck. Start from the release lever and follow to the end of the tube. There will be a metal lever that the cable was attached to before it broke. You have to pull that lever with your hand to release the parking brake. Very Important!!!...Hold the parking brake activation pedal with your other hand when you release the brake. Let the pedal out slowly when you pull the metal release lever. The pedal will come back very fast and you could injure yourself if you are not careful. Good luck!

Posted on Jul 28, 2009

  • 1 Answer

SOURCE: 2000 Chevrolet Silverado 1500 brake release cable

Same thing happened to me on my 2000 silverado July 3, 2009.
There is a release next to the parking brake pedal. You have to reach way under the dash but it has worked for me for the last month. I have the part to fix it but haven't had the time.

Posted on Aug 27, 2009

  • 20 Answers

SOURCE: parking brake cable broke, 94 chevy s10 stuck, how

If it broke it should have released itself, the system is a simple cabel pully system, if its broken the cable cant have the tension to keep the brake engadged. if you want to release the handel pull the release and physicaly move the pedal.

Posted on Feb 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How too release the emergency brake foot pedal when the cable is broken?


About 73,400 results (0.87 seconds) Search Results

    Parking brake release cable snaps - Chevy Avalanche Fan Club of ...

    chevyavalanchefanclub.com > ... > Problems: Brakes

    24 posts - ‎16 authors
    Went to release the parking brake on my 04 and the cable snapped. ... More like the end cap coming of the cable that attaches to the foot pedal. ..... Then I released the parking brake, pulled out the broken release cable/handle assembly, ...

    How To Install Repair Replace Parking Brake Release ...

    ? 5:54
    https://www.youtube.com/watch?v=qx0oGfV62NQ
    Jun 23, 2011 - Uploaded by 1A Auto Parts
    How To Install Repair Replace Parking Brake Release CableHandle ... or replace a broken or worn out parking brake release cable handle.

    Emergency Brake Pedal Assembly & Stuck Brake Cable ...

    ? 10:13
    https://www.youtube.com/watch?v=0jYfvthBzhU
    Apr 17, 2014 - Uploaded by corgLLC
    Emergency (Parking) Brake Pedal Assembly & Stuck Emergency (Parking) Rear Brake Cable The emergency ...

    E-Brake Cable Broken? Stuck Emergency Brake... Help Please ' Chevy ...

    www.tahoeyukonforum.com > ... > Engine & Drivetrain


Jan 25, 2016 | Cars & Trucks

1 Answer

How to reconnect emergency parking cables


from the rear wheel to the hanbrake

Jan 20, 2014 | 1990 Cadillac Allante

1 Answer

How do I adjust the emergency brake?


Over here we call it a parking brake - hardly any of our cars are autos.

Parking brakes usually connect to the rear disc brake calipers but some manufacturers use a small drum brake in the disc centre for parking purposes due to the complexity of the caliper with integral parking brake.

When adjusting a parking brake it is important in most designs for the cable to be adjusted only to remove any free play without moving the caliper levers from the backstops and then if the parking brake lever or pedal travel is excessive it must be because of wear or other faults. Sometimes that basic requirement must be taken with a pinch or two of "experienced" salt...

Ford have a self adjusting parking brake I have experience of. A spring within the system preloads the cable eliminating all slack in the cable so the cable moves the caliper levers from the first. The main problem with the system is the preload spring is sometimes strong enough to overcome the resistance of the caliper spring and cause a binding brake. No manual adjustment was provided.
In that case I find fabricating and fitting brackets to anchor additional return springs to the calipers is a must.

Mar 19, 2017 | 1996 Ford Windstar

1 Answer

My emergency brake cable broke with the brake engaged. how do i disengage it so i can get to a garage?


If the emergency brake cable broke, then the brake should disengage by itself, unless there is rust in the braking system preventing it from doing so.

An engaged brake needs tension on the cable to continue to hold the vehicle still.

You could have it towed by a flat bed that slowly draws the car up onto its flat bed, even if the brakes or park was engaged. Allow the tow truck operator to worry about this problem.

Good luck on getting your vehicle to the garage.

Feb 03, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

Emergency brakes not working


Could be several different things that may be causing the parking brake. The sierra uses a simple cable pull system. If the cable becomes loose you will not have emergency/parking brakes. If the cable is tight then the shoe located inside the rear brake drums is worn or broken. If there is no cable coming from the parking/emergency brake pedal inside the cab then it has been either broken out or removed at some point, which is easy to do if taken off-roading.
Keep in mind that only the rear wheels have parking/emergency brakes. Front wheels have none.

Sep 28, 2010 | 2003 GMC Sierra 1500

1 Answer

How do I adjust emerg. brake 2003 siverado 2500 hd


go under the truck on the drivers side, there u will see the single cable from the park brake in the cab go into a "Y", there is a threaded rod there, that has two nuts on it, that is the adjustment.

Jun 13, 2010 | 2003 Chevrolet Silverado 2500

3 Answers

Emergency break cable broke on 2004 silverado


I had the same problem on my 2003. Open the driver door all the way. Get on your knees just outside the door. Follow the plastic tub that holds the parking brake release cable inside the truck. Start from the release lever and follow to the end of the tube. There will be a metal lever that the cable was attached to before it broke. You have to pull that lever with your hand to release the parking brake. Very Important!!!...Hold the parking brake activation pedal with your other hand when you release the brake. Let the pedal out slowly when you pull the metal release lever. The pedal will come back very fast and you could injure yourself if you are not careful. Good luck!

Jul 27, 2009 | 2000 Chevrolet 3500

3 Answers

2000 Chevrolet Silverado 1500 brake release cable broke and won't release the emergency brake. I checked the brake release handle and cable and discovered a small nut like metal piece on the floor below...


Same thing happened to me on my 2000 silverado July 3, 2009.
There is a release next to the parking brake pedal. You have to reach way under the dash but it has worked for me for the last month. I have the part to fix it but haven't had the time.

Jul 12, 2009 | 2000 Chevrolet Silverado 1500

1 Answer

2003 silverado HD adjust emergency brake cable?


first you need to check the rear brakes ,the emergency brakes work off the rear brakes, there is an adjustment on the center of cable that goes between both rear brakes,hope this is some help,thanks robert b.

Jul 06, 2009 | 2003 Chevrolet Silverado 2500HD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...