Question about Kia Cars & Trucks

Open Question

Upper intake bolt torque spec 3.5L kia sedona

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Engine Bolt Torques- 2005 Chevy Impala/3400 Engine

Head Bolts
Step one 37 ft lbs then tignten 120 degrees more

Rocker arms
Step one 11 ft lbs then tighten 90 degresss more

Upper intake
89 inch lbs
Lower intake
132 inch lbs

Posted on Dec 02, 2008

Ad
  • 25 Answers

SOURCE: 87 samurai bolt torque specs for engine

The haynes book is not recommended since there are numerous mistakes and they still will not update. One of the biggest is the firing order.

The factory service manual is the only way to go.

Head bolts - 46 - 50.5 lbs (there is an order sequence for the bolts)

Intake & exhuast manifolds- 13.5 - 20 lbs

Flywheel - 41.5 - 47 lbs

Clutch cover - 13.5 - 20 lbs

Posted on Mar 17, 2009

LEFTY64
  • 69 Answers

SOURCE: Need to the torque specs for a 1999 Dodge Durango

Head Torque sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs recheck final torque in sequence.

Torque intake manifold: Step 1: 12 inch/Lbs, (hand tight) Step 2: 72 inch/Lbs, (6) Ft/Lbs Step 3: 12 Ft/Lbs
torque intake plenum: Step 1: 24 inch/lb (hand tight) Step 2: 48 inch/lb (4) Ft/Lbs Step 3: 84 inch/lb (7) Ft/Lbs (To torque bolts, start in center using crisscross pattern)

Posted on Apr 07, 2009

outdoorsman5
  • 631 Answers

SOURCE: head bolt torque specs for 2000 dodge neon 2.0 SOHC

I have the specs and diagrams. If you want me to send them to you, give me your email address. Outdoorsman592003@yahoo.com

Posted on Sep 05, 2009

  • 617 Answers

SOURCE: intake manifold bolts torque and rocker arm torque

Intake Manifold Coolant Pipe Bolt .... 89 in lbs (7.4166 ft. lbs)
Lower Intake Manifold Bolt .............. 115 in. lbs (9.5833 ft. lbs)
Upper Intake Manifold Bolt/Stud ...... 18 ft. lbs
Valve Rocker Arm Bolt ................... 168 in. lbs (14 ft. lbs +30 degress

Posted on Feb 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03 Dodge Intrepid intake manifold torque specs top & bottom is for 3.5 V6


Lower Intake:
  1. Use a skin coat of RTV silicone on both sides of the water passage ports (outer most holes) and put the new lower intake gaskets into place
  2. Hand tighten the 13mm head intake bolts and Torque the bolts , starting from the center and working your way out in a circular pattern
  3. Torque these bolts in a few small increments until they have reached 250 inch pounds of torque.
  4. Upper Intake Plenum:
  5. When installing the intake air plenum , be sure to catch the four center bolts and the two side bolts (stiffener brackets) before tightening , The center bolts should be torqued to 250 inch pounds .The fuel rail bolts should be torqued to 100 inch pounds

Jun 24, 2016 | 2003 Dodge Intrepid

1 Answer

Torque sequence 3400 engine upper intake


starting at the middle bolt and go directly across then criss cross the pattern like you would tightening wheel nuts, towards the outside(end) bolts. if this is a plastic upper intake the torque should be around 15ft lbs if its metal around 25ft lbs.

Sep 04, 2014 | Chevrolet Venture Cars & Trucks

1 Answer

Torque specs 2003 kia sedonna rocker arm


Tighten the bearing cap in two or three steps. Tighten it to the standard torque at the last stage. *Bearing cap standard torque Torque16 pieces at the both ends : 18.6 - 20.6 N·m(190 - 210kg·cm, 13.7 - 15.2 lb·ft)24

Jun 16, 2014 | 2003 Kia Sedona

1 Answer

I need to know how to find/set timing marks for 2002 Kia Sedona and head bolt torque specs


The head bolt torque on a 2002 Kia Optima is 45 ft/lbs of torque. Always make sure you use a good torque wrench to get it right. ------------------------------------------------------------------------------------
Original Launch X431 Master

Mar 13, 2013 | Cars & Trucks

1 Answer

Need the torque specs for the upper intake bults on a 2002 chrysler sebring conv. 2.7L


4022caa.jpg

Fig. Intake manifold bolt torque sequence 2.7L engine

Upper intake manifold with a new gasket on the lower intake manifold and torque the bolts, in sequence, to: 105 inch lbs. (12 Nm)

Hope helps (remember to rate this answer). Good job.

Oct 11, 2010 | 2002 Chrysler Sebring

2 Answers

Need torque specs for 2000 chevy malibu 3.1 cyl heads & intake


(step 1 ) the torque specs for the heads are---1998 through 2001 are 37 foot lbs. ( step 2) rotate an additional 90-degrees (1/4 turn). intake manifold bolts ( lower ) step 1-- 62 in-lbs, step 2--115 in-lbs. intake manifold bolts/studs ( upper ) 18 ft-lbs. this is for the 3.1 v-6, have a good day!

Aug 14, 2010 | 2000 Chevrolet Malibu

1 Answer

Starter for kia sportage 2000


  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Intake manifold bracket upper bolts Clutch release cylinder and move it aside, if equipped Intake manifold bracket lower bolts and remove the bracket Starter from the clutch, manual transmissions only Starter from the torque converter, automatic transmissions only Starter electrical connectors Move the transmission wire harness aside Starter


    0900c152801b0603.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the starter

To install:
  1. Install or connect the following:

    Starter to the engine well Starter electrical connectors Lower intake manifold bracket and install the upper bolts Starter into position. When aligned properly torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket bolts to 40 ft. lbs. (54 Nm). Properly position the clutch release cylinder, if equipped. Torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket upper bolts to 40 ft. lbs. (54 Nm). Negative battery cable

Jun 28, 2009 | 2000 Kia Sportage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,296 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...