Question about Cars & Trucks

Open Question

07 Lucerne has rattle in rear, seems to be brake calipers, when brakes applied rattle stops.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: 2000 chevy 1500 silverado- rear brakes overheating

Have someone push & release pedal while at wheel with problem. See if it takes a while or slow to release. If yes, have wrench ready on bleeder screw, and try again, if it sticks/holds, crack bleeder screw, if it releases, I'd replace hose.

Posted on Jan 18, 2009

Ad
  • 2 Answers

SOURCE: cant compress piston on rear brake calipers

Use a caliper wind back tool which rotates the piston at the same time as pushing it back. Release the bleed screw to assist the wind back. If you use a brake hose clamp on the brake hose this will reduce the need to bleed the system.

Posted on Apr 13, 2009

  • 44 Answers

SOURCE: how change brake pads on 07 expedition

loosen the bleeder screw and try to press the caliper in some.

Posted on Aug 28, 2009

  • 271 Answers

SOURCE: how to compress rear brake caliper piston

Only way is to use diagnistic equipment.Go to HAND BRAKE . There is option to release the pistons.When you change the brake pads you have to use option - engage .

Posted on May 15, 2010

roniecon
  • 6826 Answers

SOURCE: the rear brakes calipers seem ceased up when

If the calipers have two,or four notches in the piston of the calipers,then the pistons have to be turned in,one side turns left,and the other right,then they will go back,the auto parts store sells a cheap tool for this,that you use a 3/8 drive ratchet with,if this was helpful,please rate,and thank you

Posted on Jun 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

There is rattling/clicking sound coming from under my 02 galant. Just replaced both axles but said sound is still there. What is it and what can I do to fix it?


If the sound stops when you lightly apply the brakes it is probably disc brake pads that weren't properly installed and they are rattling now that they are worn down. There should be a clip and disc brake quiet that keeps them attached to the piston cup of the caliper. If not they will rattle back and forth in the distance between the caliper cup and the rotor when the brakes are not applied.

Sep 15, 2014 | 2002 Mitsubishi Galant

2 Answers

I have a 2006 f-250, i have a grinding noise that sounds like it is coming from the rear wheels, but when i apply the brakes it stops.


How To replace front Brake Pads. In 90% of the car manufacturers the job will be done the same way. This is F250 Ford 2006

Jul 26, 2014 | 2003 Ford F250

1 Answer

Brakes chirping


Anti rattle plates in caliper are damaged/missing if new can't be sourced thin smear of silicon on rear of pad will stop this( allow silicon to dry before reinstalling pads)

May 31, 2012 | 1999 Jaguar XK8

2 Answers

Brakes rattle


To your direct question - I don't know the Highlander model in detail, but as a general response, if the brakes are noisy when NOT applied, the piston in your new caliper may not be returning properly.

The return spring in disc brakes is actually the rubber fitted around the caliper piston. If this is causing the piston to be wrongly positioned, the brakes will be noisy. Check that the rotor can be turned by hand when the brakes are not applied. Also check that the piston is not retracting from the pads a very long way, which it should not do.

It is worth making very sure the spring clips are fitted correctly. Some can be easily put in the wrong way round.

If the brakes are squealing when applied, that is a different problem. You can get a disc brake anti squeal liquid, which is applied to the back of the pad on assembly to the caliper. Also double check all the anti squeal shims are correctly installed.

At this range, that's all I can think of right now.

Nov 24, 2011 | 2005 Toyota Highlander

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

1 Answer

2003 Dodge Grand Caravan Sport FWD. Acceleration and braking


if any thing the calipers could be sticking but the ratcheting noise in reverse is normal

Aug 06, 2009 | 2003 Dodge Grand Caravan AWD

1 Answer

Rear brake pads rattle


There are spring clips which keep the pads tight in the caliper. These spring clips are missing, or are broken, or have lost their tension, etc.

May 27, 2009 | 1997 BMW 328

1 Answer

Worn brake pads


Front brake pad exchange guide.

Step1 Park the Dodge Durango on a flat surface. Put the emergency brake on and put wedges behind the wheels to prevent the vehicle from rolling. Disconnect the negative battery cable from the battery. Drain 2/3 of the brake fluid from the master cylinder, using a syringe. Remove the wheel and the tire assemblies. Step2 Compress the caliper piston back into the caliper bore using a large C-clamp to drive the piston into the bore. Use additional force if it is required. Using a 3/8 inch hex wrench or socket remove the caliper mounting bolts. Step3 Rotate the caliper rearward off the rotor and out from its mount. Remove the inboard and outboard brake pads. Remove the spring clip that holds the inboard brakes in the caliper. Tilt the pad out at the top to unseat the clip. Remove the retaining spring that secures it in the caliper. Unseat one spring end and rotate the pad out of the caliper. Step4 Suspend the caliper assembly from the Durango frame using mechanic's wire. Do not allow the caliper assembly to dangle from the brake hose as this may damage the brake hose. Step5 Clean the surfaces of the caliper and steering knuckle with a wire brush. Apply multi-mileage grease or similar product. Using brake fluid or break cleaner clean the caliper slide pins. Apply a light coating of silicone grease to the pins. Step6 Install the inboard brake pad and it's spring. Install the outboard brake pad. Install the caliper over the rotor and seat it in its original position until it is flush. Using a torque wrench, torque the slide caliper pins to 22 ft./lbs. Step7 Add brake fluid to the master cylinder. Bleed the brakes. Reconnect the negative battery cable to the battery. Start the engine and pump the brakes 3-4 times to seat the brake pads. Reinstall the wheels. Test drive the Durango at slow to moderate speeds to ensure that the maintenance was performed correctly.
Rear brake pad exchange.

Step1 Lift the Durango off the ground with a car jack. Support the vehicle on all sides with jack stands. Keep children and small animals out of the vicinity when you replace the brakes. Step2 Loosen the lug nuts on the wheels with a torque wrench. Remove the wheel and tire assemblies and set them aside, face up, to prevent damage. Step3 Compress the caliper and remove it by lifting the top up and off the caliper adapter. Hang the caliper from the Durango's frame with mechanical wire. Step4 Remove the inboard and outboard brake shoes from the caliper adapter. Take off the top and bottom anti-rattle springs. Keep the springs separated, as they aren't interchangeable. Step5 Press the piston into the bore with a C-clamp. To prevent damage to the pistons, insert an old brake shoe in between the C-clamp and caliper piston. Remove the C-clamp. Step6 Wipe down the caliper mounting adapter and anti-rattle springs with brake cleaner. Grease the anti-rattle springs with brake grease. Install the bottom anti-rattle springs, followed by the top anti-rattle springs. Step7 Install the inboard brake shoes followed by the outboard brake shoes. Replace the caliper and the wheel and tire assemblies. Lower the vehicle to the ground and pump the brakes to seat the pistons.


Please rate and god bless:)


Apr 02, 2009 | 1999 Dodge Durango

1 Answer

Constant replacement of rear rotors


first i would the car to a professional auto repair shop and have the brakes evaluated. you may have to pay a small fee, but it will pay for itself in the long run. it sounds like the rear calipers are sticking or dragging, or the parking brake is also dragging. the rear calipers are actuated, they stop the car in normal braking and they also are used when the parking brake is applied, the caliper piston will move out and keep the car from rolling when the parking brake is applied. worst case senerio you may need to replace the rear calipers, caliper brackets, rear brake hoses and both rear rotors, unless they can be resurfaced. the vibration or pulsation is more than likely excessive runout or thickness variation in these rotors from the calipers dragging (not releasing). also if the car takes too much effort to stop and you have had to replace these rotors 4 times, that is not normal. have a repair shop check to see if the brake fluid is contaminated. a good and quick sign to check for contamination is if the rubber under the brake fluid cap is distorted.please do not drive this vehicle until it is checked out by a professional auto repair shop. thanks

Oct 18, 2008 | 2002 Chevrolet Camaro

1 Answer

Sporadic squealing/rattling from the rear


BRAKES ARE RATTLING IN DISC BRAKE CALIPER, TRY NEW SET OF PADS WITH FIXING KIT/TENSION SPRINGS..

Sep 25, 2008 | 2004 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...