Question about Cars & Trucks

Open Question

Replace steering cable on 1976 Ranger Boat W/85HP Johnson Motor

Cable broke and need to take old cable off

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
thabrain
  • 76 Answers

SOURCE: How to replace 97 Grand Cherokee hood latch release cable?

remove bolts where handle use to be drop it down. make sure hood is up first, find where cable ties into hood release it should unclip or slide out when unhooked, use channel locks . pool cable out through the inside of car noting where it enteres the firewall. replace in reverse fashion that you took it out. hope this helps

Posted on Oct 28, 2008

Ad
  • 1 Answer

SOURCE: Replace actuator cable for front driver side window motor

I also Have this problem, just happened, is their a way to repace this

Posted on Nov 18, 2008

  • 203 Answers

SOURCE: how do i replace a broken hood latch cable 2002 toyota camry

its more fiddly than hard before you start look st the cable where it joins the latch and start following it back toward the lever you may have to lift some floor mats etc and the cable should be secured with clips along the way if you think you can get it out take it with you when you go to buy the new 1 and make sure they are the same. if this helps please rate joe

Posted on Dec 06, 2008

  • 73 Answers

SOURCE: 99 VW Beetle Hood Release Cable plastic tab broke

the only way to purchase is a whole cable

Posted on Jul 01, 2009

  • 1071 Answers

SOURCE: i need to replace the window cable in my passat

get a complete regulator from vw or check fcp groton .com i am a vw tech you will be there forever if you try the cable you will never get it wound around regulator leaving you with a window that doesnt work

Posted on Jul 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Install steering column,on 99ford ranger video.,,shifter broke. or pics


instead of fixing the broken column go to local salvage yard and replace the entire column it should take you about 2 hours to replace it not even that. it is too much of a hassle to fix a broken part in the column itself and the repair will not always help out in the long run.

Apr 25, 2016 | 1999 Ford Ranger SuperCab

2 Answers

What is this and what kind of motor goes on it?


it looks to be a boat and from the poor quality photo it appears to gave a prop under it
in which case it will have an inboard n motor fitted with a drive shaft connected to the fly wheel or harmonic balancer end
from the view of the cut down transom it may take an out board as well
talk with a boat shop to get it right

Dec 17, 2015 | Cars & Trucks

1 Answer

Rear door on left drivers window drop in track cable is the cable just of or should i replace motor 2003 dodge durango


you will have to remove door panel and check. most likely the cable broke and you will need to replace motor mechanism

Apr 18, 2011 | 2003 Dodge Durango

1 Answer

I have a 1976 ford 100 xlt ranger with a 360 moter 2 wheel drive automatic the starter was recently replaced and it just kept engageing what do I do other than get out and kick the dawm thing


WHEN YOUR OLD STARTER WENT BAD IT MORE THAN LIKELY PULLED TO MUCH AMPERAGE THUS WELDING THE CONTACTS INSIDE THE STARTER SOLENOID TOGETHER. REPLACE THE SOLINOID ITS LOCATED ON THE FIRE WALL SAME SIDE AS YOUR BATTERY THE POSITIVE CABLE FROM YOUR BATTERY IS ATTACHED TO IT. THI IS A PIC OF WHAT IT SHOULD LOOK LIKE .HOPE THIS HELPS


shortgap.jpg

Dec 20, 2010 | Ford F-100 Cars & Trucks

1 Answer

How do you open a hood on 1976 corvette when cable is broke?


If the cable broke in the cabin, pull off the side panel in the footwell and use a pair of channel locks or good pliers to pull on the cable to get the hood open.

If it broke at the hood you'll probably need to lift the car and see how to get to the release by getting between the radiator, front end and grasping the latch.

Sep 21, 2010 | 1972 Chevrolet Corvette

2 Answers

My key broke off in my 95 Ford Ranger ignition, how do I get it out? the switch just keep turing when I try to turn off the vehicle.


If the lock just keeps turning the cam inside the steering column is broken. Bigger problem than just a broken key. If you can't get the engine to turn off, use a thick towel to "smother" the engine air intake, then disconnect the negative battery cable. You will need a tow truck to take the vehicle in for repair so you might want to drive it to the shop before you do this.

Oct 25, 2009 | 1996 Ford Ranger SuperCab

1 Answer

Cant read wirring diagram


as long as the steering lock no longer works you can leave the original switch where it is and mount your new switch in a convenient place. unplug the cables from under the steering column and extend them to your new switch. you should only have 4 cables there to go on your new switch. the battery cable is the one that is live all the time, a thick cable, the ignition is the one that makes the ignition lights come on when the key is turned, a thick cable, the accessory cable is the one that becomes live when turned to 1st position on key, a thinner cable, the starter cable is the one that goes to the starter motor when key turned to start a thick cable. hope this helps

Apr 23, 2009 | 1986 Ford Ranger 2WD

2 Answers

1989 ford ranger 2.3l starter keeps buning out after 3-4 months


After 20 years of use, it would not hurt to replace not only the positive starter cable, but the negative cable from the battery to ground, and look for the ground wire from the chassis to the motor. An old connection can cause a lot of trouble. Never use those clamp on terminal repairs, always buy a good new cable.

Apr 04, 2009 | 1989 Ford Ranger

2 Answers

1996 ford ranger odometer / trip stopped working


Since your speedometers work, the problem is in the gearing to the trip and mileage odometers. Simple problem, major pain to fix but, remove instrument cluster - you'll have to remove speedo cable to get it out. Use the old Mark I eyeball to check for broken parts. Might even have to drop steering column - disconnect air bag first!

Jan 30, 2009 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...