Question about 2007 Chrysler Crossfire Convertible

Open Question

Grease fittings Show where grease fittings are.

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I remove the pressed in grease fitting on a 1930 Ford


Grab it with a good set of vice grips and work it out, I have had grease fittings that won't take grease and some of them the parts had to be removed and the lube hole cleaned out. you can also buy a grease injector that is a hollow barrel with a plunger that fits down in it and you pull out the plunger fill the barrel with grease install the plunger, place the injector on the grease fitting and hit the plunger with a good size hammer

Jan 12, 2016 | Ford Cars & Trucks

1 Answer

Front end grease fittings


I replaced all of my joints, ball, tie rods, etc with grease fittings. If you can't see or feel them, there are none. You can try a grease needle that are sold at auto parts stores for cheap. You have to pierce the joints and inject them slowly. Eventually you'll have to replace them with joints that have fittings.

Mar 30, 2014 | 1991 Isuzu Trooper

1 Answer

Where are the grease fittings for ball joints on 1992 Nissan Sentra E


The vast majority of cars today do not have grease fittings for most components. They are sealed for the life of the part from the factory.
Only some replacement parts come with grease fittings.

Jan 21, 2013 | Cars & Trucks

1 Answer

How do i grease the ball joints 1992 Nissan Sentra E


Here's a link to the lower ball joint,it tells you about a fitting to be greased,as you see the ball joint has a hole at threads where greasing fitting will be.It will be best to jack up and remove tire to grease,look for other grease fittings,wipe up excess grease.Also check ball joint for wear,may need replacing.

Jan 20, 2013 | Nissan Sentra Cars & Trucks

1 Answer

Does a 201 pontiac sunfire have grease fittings?


alot of these cars don`t have grease fittings from the factory as they are considered lifetime(permanent) greased components.however this doesn`t always work.if the components have at one time been replaced then they will have a grease fitting in them that needs to be greased.

Jun 29, 2011 | 2001 Pontiac Sunfire

2 Answers

Have 20,000.00 miles on car and the front end makes a creaking noise when turning steering wheel...need to grease but no grease fittings how do you get rid of noise


most newer cars came that way so you cant grease them this way you almost have to buy after market with grease fittings thay get you coming and going the only thing you can try is p-b blast spray it on the parts and hope it works good luck let me no if you need any thing else.

Apr 24, 2011 | 2000 Lincoln Continental

2 Answers

ARE THERE GREASE FITTING ON THE FRONT END OF THE 2005 AND 2007 F 150 TRUCIS. I SNED MY FLEET TO BE SERVICED AND THEY COME BACK STATING NO LUBE


Grease fittings don,t come on new trucks anymore
I Have 2005 F 350 and a 1999 F450 and there is no grease fittings

Aug 30, 2010 | 2005 Ford F-150

1 Answer

Can you show me detail pictures of step by step repair of ball joint and controll arm of 1990 ford thunderbird v6 3.1 automatc


prev.gif next.gif REMOVAL AND INSTALLATION Upper ball joints are not replaceable. The upper ball joint is part of the upper control arm bushing joint and is not serviced separately. If the upper ball joints are found to be defective, the entire upper control arm bushing joint assembly must be replaced. Lower Ball Joint INSPECTION
  1. Support the vehicle in normal driving position with ball joints loaded.
  2. Wipe the grease fitting and checking surface, so they are free of dirt and grease. The checking surface is the round boss into which the grease fitting is threaded.
  3. The checking surface should project outside the cover. If the checking surface is inside the cover, replace the lower arm assembly. prev.gif next.gif

Aug 26, 2010 | 1990 Ford Thunderbird

1 Answer

Where are the grease fittings ?


Manufacturers generally removed grease fitting from suspension part back in the 80's. Some put a removable plug in the ball joints, tie rod ends, etc, which could be removed and grease fittings installed in their place, but most have sealed and permanently greased. In other words you can not lubricate any fittings. If parts go bad, the replacement suspension parts generally have grease fittings.

Aug 10, 2010 | 2000 Mercury Grand Marquis

1 Answer

GREASE FITTINGS


there are either grease fittings or plugs where they go, the fittings will be in the ball joints and the tie rod ends. should grease about every 6,000 miles or so, if u go through water allot more often

Jan 15, 2009 | 2008 Hummer H3

Not finding what you are looking for?
2007 Chrysler Crossfire Convertible Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...