Question about Cars & Trucks

Open Question

Infiniti qx4 engine diagram

Change water pump

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: How to change Headlight HID bulbs in Infiniti QX4

It is really not that difficult for an 01 qx4, and if you order the bulb online you'll save enough money that if it takes you two or three tries (and bulbs) you'll still save over what the dealer or a mechanic would charge you:
Don't touch anything on the new bulb besides the plastic base (don't touch the glass!)
1. Make sure you disconnect the battery before anything else (you don't want to get shocked by these high voltage babies). If you're replacing the passenger side bulb, take the battery out for more room to work, especially to see what's going on in there (you can undo the air filter case on the drivers side for the same benefit, again--disconnect the battery first). 2. Find and unscrew the round, black, plastic lid behind the headlight, it's up and to the left. 3. You'll see a shiny metal connector with electrical warnings printed on it and Michael Jackson glove looking wiring attached to it. Turn that gently to the left to open up access to the actual bulb (you'll now see the bottom/back of the bulb--a black circle with a small metal tip in the middle). 4. Unhook the two metal braces that hold the bulb in place (push in gently to let wire out--kind of like unhooking a bungee cord or unsetting a mouse trap). 5. Pay attention how the two divots on the bulb case line up with the little nubs at the top of the encasing (you have to put the new one in lining up the same way.) 6. You can now take out the bulb. You might consider practicing the replacement sequence with your old bulb that you just took out before sticking the new one in there--just to get the hang of it so you aren't banging the new one around. 7. Once you've got the bulb back in there just put everything else back in place in reverse order. 8. Wash those dirty hands and try turning on your lights. 9. Go celebrate your automotive victory by driving somewhere at night!

Posted on Aug 28, 2009

canbruce75
  • 1776 Answers

SOURCE: how to change water pump in 2002 alero and a

I suggest that you visit the autozone.com website and register the vehicle. It doesn't cost anything and will give you access to an online repair manual. The steps for replacing the water pump should be available there. Hope this helped and best wishes.

Posted on Sep 01, 2009

  • 312 Answers

SOURCE: Pls where is Swirl Control Solenoid Valve located in Infiniti QX4

This link shows the location of the SCV, If your motor is different the location should be similiar. http://img510.imageshack.us/img510/5687/vacuumdiagramuh3.jpg

There's a vaccuum line that runs off the SCV to the SCV check switch.

P0442: Have you inspected the lines, charcoal cannister etc? Make sure the fuel cap is tight. The easiest way to check the system is to have someone perform a smoke test. I had a DTC on my car which indicated a EVAP problem, it turned out to be the Fuel tank evaporator Control Solenoid.

Posted on Sep 22, 2009

emissionwiz
  • 75222 Answers

SOURCE: do i have to pull off the intake to change the

YES IT IS Under the lower intake manifold... the entire manifold must be removed which is a 2.5hr job... and you will see it on the engine block itself

Posted on Nov 10, 2009

Testimonial: "thank you sir, very helpful"

  • 1 Answer

SOURCE: tryen to find location of the crank sensor on 1998 infiniti QX4

looking for crankshaft sensor on 1998 infiniti qx4

Posted on Nov 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset service engine soon light on 2002 Infiniti QX4?


Here's a YouTube video to reset the reminder on the Infiniti/Nissan.
Nissan Infiniti oil service reset

Nov 08, 2016 | 2002 Infiniti QX4

1 Answer

How to change the crankshaft position sensor on a1999 Infiniti qx4


The crank sensor is located at the driver side rear of the engine. it is bolted to the transmission bell housing. Here is a diagram of it's location.


Click on link for location diagram. http://ww2.justanswer.com/uploads/baddad1/2012-01-11_220732_capture.png

Nov 03, 2016 | Infiniti Cars & Trucks

1 Answer

Changed thermostate but heater wont get hot and engine temp goes way high


This will happen if the system is not completely bled of all air. If you are sure there is no air in the system you may have a defective water pump impellar or possible headgasket issue

Jan 05, 2016 | 2001 Infiniti QX4

1 Answer

99 infinity qx4 where is the fuel **** located


The fuel pump is located inside the fuel tank and is accessed through an access cover behind the rear seat.

Jun 25, 2014 | 1999 Infiniti.5 QX4

1 Answer

When does the timing belt need to be changed


every 60,000 miles. These motors will encounter severe damage if the timing belt isn't serviced/or serviced properly. I recommend replacing the tensioner pully, water pump, cam/crank seals. They are all within the timing belt area. Hopefully this helps

Apr 05, 2010 | 1999 Infiniti.5 QX4

2 Answers

What is the firing order for an Infiniti V6 3500 engine?


Here's the firing order diagram as you requested...


a23b44e.jpg

Mar 14, 2010 | 2004 Infiniti QX4

1 Answer

Do i have to pull off the intake to change the knock sensor 1997 infiniti QX4 where can i find a free diagram


YES IT IS Under the lower intake manifold... the entire manifold must be removed which is a 2.5hr job... and you will see it on the engine block itself

Nov 10, 2009 | 1999 Infiniti.5 QX4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...