Question about Cars & Trucks

Open Question

Tata sumo victa no starting problem,when idling noise occured.after pressing the clutch pedal fully noise arrested.pls give some solution.

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: engine or transmission knock / rattle upon

I had the same problem on my 2006 Lucerne and it was the engine mount located on the front of the vehicle behind the radiator.

Posted on Aug 24, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is clutch pedal making a single clicking noise everytime it is released ?


The click you are hearing is most likely coming from the clutch safety switch, which prevents the car from starting unless the clutch is fully depressed. Some vehicles use a relay to activate/deactivate the safety feature when the clutch pedal is cycled.

Dec 24, 2014 | 2007 Hyundai Elantra 2.0

1 Answer

Car turns off when engaging clutch to a lower gear


Check the following:
- Thrust bearing, clutch.
TEST: Pull up the hand brake. Start the engine and let it at idle speed.
Depress the clutch pedal, put the car in 1st gear, while keeping the clutch pedal depressed. If the gear lever hesitates or produce any abnormal noise, replace the clutch thrust bearing.
- If the gear lever shifts smoothly, clean the throttle body, idle air control valve and perform idle speed learn learn procedure.
- Check the valve clearance.

Apr 11, 2014 | 1992 Toyota Corolla

1 Answer

1998 Ford Taurus SE, Problem Transmissions wont Shift, Took it to the Shop and they Said it Had to be a Electracal Problem?? But they did not Know what, Some times Works Fine Other Times Check Engine Comes...


TRY THIS I BET IT'S YOUR PROBLEM

Neutral Safety Switch
  • Put the selector in the park position.
  • Loosen the screws on the neutral safety switch.
  • Remove the switch.
  • Reverse the procedures to complete the installation.
Clutch Start Switch
CAUTION
Before replacing the clutch switch or any component connected to the vehicle's control computer, disconnect the negative cable from the battery.
  • After replacing the switch, slowly work the clutch pedal and note any unusual noises or interferences with pedal movement.
  • If the switch is adjustable, make sure the clutch pedal height and push rod (free) play are correct.
  • Then check the release point of the clutch.
  • Begin by engaging the parking brake and installing wheel chocks.
  • Start the engine and allow it to idle.
  • Without depressing the clutch pedal, slowly shift the shift lever into reverse until the gears contact.
  • Gradually depress the clutch pedal and measure the stroke distance from the point the gear noise stops (this is the release point) up to the full stroke end position.
  • If the distance is not within specifications, check the pedal height, push rod play, and pedal free play.
  • If the distance is correct, check the clearance between the switch and the pedal assembly when the clutch is fully depressed.
f_mt_tps9.26.jpg Clutch switch to pedal assembly clearance. Courtesy of Toyota Motor Company.
  • Loosen the switch and adjust its position to provide for the specified clearance.

May 22, 2010 | 1998 Ford Taurus

1 Answer

Grinding noise after shifting


The clutch pedal need to be adjusted ,while you press the pedal clutch,it is not disengage fully the gear box that why when you shift it make that noise,well hope that clear your mind and help you.

Jan 28, 2010 | 1997 Honda CR-V

1 Answer

Grinding Noise When Clutch Is Depressed, Lights Flicker


you may need to have your clutch cable adjusted ... it is most likely not releasing the clutch fully and grinding against the flywheel

Oct 06, 2009 | 1998 Volkswagen Jetta

1 Answer

Isuzu Trooper Clutch Pedal Issue


either it is a clutch fluid line busted (most likely)or its you clutch master you can start it anyway give a little gas in 1st and start it shut it off b4 starting i drove my volvo 740 home like that once nerve wrecking but save towing money

Jun 19, 2009 | 1993 Isuzu Trooper

4 Answers

Transmission shifting proublem M5R1 1997 FORD RANGER


internal slave cylinders are known to leak , unfortunate it is behind clutch assembly , i would change both , clutch master and slave cylinder

Feb 27, 2009 | 1997 Ford Ranger SuperCab

1 Answer

To change gears, I need to fully press down on my clutch pedal to stop a grinding noise on my hyundai accent 2001Can I adjust the clutch cable,


Hi and welcome to FixYa,

In a manual 2001 Hyundai Accent, the clutch cable could be adjusted. The adjustment point is on the cable 'pad' where it enters the firewall in the engine compartment.
86c2d7d.jpg
To adjust, the slack or free play must be decreased. This is done by turning the adjusting nut clockwise. Check back by pressing on the clutch pedal to your preference.
73309c3.jpg
Good luck and thank you for using FixYa.

Feb 18, 2009 | Hyundai Motor 1995 Accent

1 Answer

Clicking noise when car is idling


i think the problem in the transmission box...you must take your car to the nearst hyundai work station and ask to mechanic to check transmission box ( Oil, Clutch etc) maybe this time you need to replace the clutch...

Feb 02, 2009 | Hyundai Motor 2003 Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...