Question about 2001 Chrysler PT Cruiser

1 Answer

Wiring diagram car has power but when I turn the ignition nothing happens

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 81 Answers

Do you try to read the fault codes with obd2 scanner.

Posted on Jul 27, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When turn key nothing happens


check connection and wires at battery for damage or corrosion if good check for power to ignition switch if no power check for damaged or shorted wiring if good turn key and check if power going to relays or accessory's at fuse panel if no power switch may be bad

Apr 08, 2014 | 2002 Saturn S-Series

1 Answer

I have a 1999 acura 3.5rl. You put the key in and turn it to start position and nothing happens. I thought it was the battery but with the lights and turn the key the lights stay bright. will not come out...


Sure sounds like a bad ignition switch to me. Get out your voltmeter and wiring diagram and check for power in and out at the ignition switch

Jun 28, 2017 | Cars & Trucks

1 Answer

Ignition problem


Check if the small wire on the starter has power with the key held in crank position. If battery voltage there, either bad battery cables or connections, or the starter solenoid has a malfunction. If no power when key held in start, it could be the safety switch (a clutch interlock switch on manual transmissions, or a park/neutral switch on automatics). You may need a wiring diagram to see the start circuit from ignition switch to the starter solenoid-some have a start relay in that circuit.
Find wiring diagrams at http://www.bbbind.com/technical.html
Free TSB's and wiring diagrams for every make and model.

Feb 09, 2014 | Cars & Trucks

1 Answer

When i turn the key on my 97 lumina the engine does not crank


Get a wiring diagram and check for power on all the power wires at the ignition switch. This is a known problem

Jan 23, 2018 | 1997 Chevrolet Lumina

1 Answer

My car has power to lights but no power to everything else


I THOUGHT EVERYTHING ELSE HAD POWER YOU MAY HAVE A IGNITION SWITCH OR FUSE ISSUE YOU REALLY A WIREING DIAGRAM AND TEST LIGHTL

Jul 13, 2012 | 1995 Toyota Corolla

1 Answer

I have a 95 chevy lumina 3.1 liter car. When I turn the key, the all the light work but nothing happens when turning the key to the start position. The battery, starter, and solenoid are all fine. I...


There is a fuse from the ignition switch. There is also a fusible link. Below is a wiring diagram that you can look at and it has the wire colors as well. This I hope will help you narrow down your power loss to the solenoid. If you need anymore wiring diagrams for your vehicle I have them all and you are free to email me at csautomotivecars@att.net with what you need. No cost, Being nice cause it's Sunday....LOL Anyway, I hope this helps you and good luck. Here's your diagram


clifford224_116.gif

Apr 03, 2011 | 1995 Chevrolet Lumina

1 Answer

1988 Doge Ram will not turn over.


check your starter relay in the power distribution center. if you are not getting any crank. with a test light or dvom you can check the small signal wire on your starter solenoid when the key is in the crank position there should be power on this wire. it sounds like you are not getting signal to the starter from the ignition switch

Apr 16, 2009 | 1988 Dodge Ram 50

2 Answers

Car wont do anything when key is turned on.


magnetic pellet ,doesn't have one . Besides it's not a magnetic pellet . It would be a resistor pellet for the anti- theft system , which your vehicle does have . And it wouldn't be the ignition lock cylinder either if you can turn the key to the start position . Possibly the electrical part of the ignition switch . Viewing a wiring diagram for power flow and checking with a DVOM - digital volt ohm meter would be the proper way to diagnose .Free wiring diagrams here http://www.bbbind.com/free_tsb.html Enter vehicle info. year , make , model and engine size . Under system click electrical distribution ,then under subsystem click on power distribution . Click the search button then the blue links . The light's work because they have seperate power supply ,looking at first diagram you will see this . Thrid diagram down is ignition switch power feed . Top right of the page you will see the letter A , that gets B+ voltage from fusible link B . Finding the ignition switch under the dash on the bottom of the steering column an testing for B+ voltage on the red wire . If B+ voltage is there fusible link is good . Fusible link B is attached at the starter solenoid .B+ stud . If there is B+ power to the ignition switch check for power from the switch .Can you figure that out ? You should also check out some videos on youtube for basic automotive electrical testing .
Electric Testing Techniques You Need to Know

Oct 12, 2017 | Chevrolet Camaro Cars & Trucks

1 Answer

Engine does not start?


Make sure that the connections at the battery is clean and free of acid built up. Take the terminals of and clean them propperly

It could also be the ignition switch at the wiring end not making proper contact anymore, try and wiggle the ignition wiring if possible and see if there is any change in the status when the ignition is switch on

Oct 26, 2008 | 1988 Nissan Pulsar

Not finding what you are looking for?
2001 Chrysler PT Cruiser Logo

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...