Question about Cars & Trucks

1 Answer

How do u get egg off aluminum siding - Cars & Trucks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 22,326 Answers

Try some weak warm vinager ,any sort of mr muscle type cleaners will stain the ally What about good old fashioned warm soapy water

Posted on Jul 26, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Retro egg beater stuck.

Sometimes screws to take something like this apart might be under a label on the unit (like the model/serial number label). If the label is rigid/metal, you might be able to pry it off with a small Exacto blade or something without destroying it. Since the unit is so old, it might just pop right off. Later, you could refasten the label with very thin double-sided tape or a thin layer of household cement. Good luck.

Jan 19, 2018 | Cars & Trucks

1 Answer

How to tell if eggs are bad

Fill a glass with water and place the eggs in one at a time.
If the egg sinks it is good. If it floats off the bottom, it is an old egg which may be bad.
The older an egg gets, the larger the air sac inside the egg gets. The larger the air sac gets the easier the egg is too float.

Dec 31, 2017 | Cars & Trucks

2 Answers

Do akes lay eggs or do they birth

Depends on the snake.

Not all snakes lay eggs--70% of them do, while the rest give live birth. Snakes that give birth to their young without laying eggs are called viviparous. These snakes live in colder climates, where eggs would not incubate as well. Snakes that lay eggs fall into two categories, oviparous and ovoviviparous. The eggs have a hard shell that protects them, and they are usually placed under leaf litter or loose soil, or within a hollow stump or burrow.

How Do Snakes Lay Eggs eHow

Jun 17, 2016 | Cars & Trucks

1 Answer

Where is the second valve two regas your aircon

between the condenser(panel on front of radiator) and the fire panel
follow the thin aluminum line and you going to find that valve..
thats the high pressure side... use the low pressure side to recharge the gas...the thick aluminum line..

Feb 28, 2015 | Cars & Trucks

1 Answer

Fuel pressure regulator

2006 navigator has a fuel pressure control module...its located behind the drivers side rear wheel. It is an aluminum box with a couple of bolts holding it. unplug it and remove.Look on the back side of it and you will most probably find a hole from corrosion. They bolted the aluminum box to steel without any insulators..the replacement part will have rubber insulators.....poor design

Sep 11, 2013 | 2006 Lincoln Navigator

1 Answer

My 2005 dodge caravan xlt burns to much gas

You don't say whether the check engine light is on or not so I'll assume it's not. If it isn't the PCM is evidently happy with the way the engine is being controlled. That leaves other things like underinflated tires and driving habits. Vehicles with aluminum wheels have a problem with bead leaks. Accelerating slowly and anticipating stops are important. Drive as though there's a raw egg between your foot and the gas pedal.

Jul 17, 2011 | 2002 Dodge Grand Caravan

1 Answer

A/C not cooling, need a diagram for the high and low sides of the system and does it use r12 or 134a freon

Low pressure side port is in the aluminum tube going to the accumulator ( an aluminum cannister about the size of a soda can or somewhat larger) Will have a plastic cap on it you unscrew to access the port valve.Your system takes R134a, it is the only commercially available refrigerant for automobile use.

Jun 15, 2011 | Ford E-150 Cars & Trucks

2 Answers

Where,exactly, IS the low line port for recharging the AC on my 2003 Chevy Malibu? OR is the coupler that came with the recharge kit the wrong size? I've assumed that most AC units have a standard...

You found the high side port. The other line should have the low side and if it is not on there it might be at the AC evaporator which is a cylinder shape made of aluminum. The cap will have a L on it not a H. Do not force it on the high side.

Jun 12, 2011 | 2003 Chevrolet Malibu

1 Answer

Where is air cond. orfice on a 2001 tauras i know

low side fitting is located by firewall on passenger side on low side hose, which is the big aluminum line...high side fitting is closer to radiator on smaller aluminum line

Aug 15, 2009 | 2001 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14264 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides