Question about Lexus GS 300

1 Answer

Car touch screen

My touch screen works fine but wont stay on

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Call the cops

Posted on Jul 26, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wont stay running


ignition switch assembly. that what it sounds like.start there.

Jun 26, 2013 | 1984 Nissan 300ZX

1 Answer

95 dodge neon wont go into reverse


Reverse clutch pack problem .

Mar 11, 2017 | Cars & Trucks

1 Answer

The crank pully fell apart on my 2007 mercury mountaineer


my 2007 mountain navigation system wont read the cd, but along with that my touch screen will only stay unable to read cd, I cant change any of my radio stations nor switch my medi system none of the buttons on steering wheel or radio work, my radio is on ,but one station,, does the cd needed for navation system run the media and radio

Apr 06, 2012 | Mercury Cars & Trucks

1 Answer

I have a 2004 concorde 2.7 liters , i just washed the car , suddenly check engine light appears out , the car shifts fine within the early few minutes but later it wont shift to 3rd it stay on 2nd gear,...


Could be water that touched one of your electronics that makes your transmission having problems try to dry the Transmission electronic connectors with low air pressure and see whats happens.Good luck

Dec 13, 2010 | 2004 Chrysler Concorde

1 Answer

My lexus IS 300 model 2007 the touch screen is not working when i press on "I agree" button it is not working all the touch buttons are not working i have tried replace the battery after this...


dear did you found any solution. because i have also IS300 2008 and everything was working fine but after cleaning the car in cleaning station (full cleaning with polish for exterior and interior) now touch screen not working at all, only side buttons, sometimes when i press the side navigation button and i touch the screen it will move the map only down but for climate and other setting no response at all..

need your help pleaseeeeeeeeeeeee

Nov 25, 2010 | 2007 Lexus GS300

1 Answer

Wont start


Its old enough, how about the coil packs? Crank position sensor?

May 16, 2010 | 2000 Oldsmobile Intrigue

1 Answer

My turn signal lights wont work on my 95 firebird formula


Go under the dash on the drivers side, and locate the two flasher stat units. These are small round aluminum 'cans'. They plug in, and have flat blades on the bottom. (You of course won't see these flat terminal blades until you unplug them)

One is for the turn signals. One is for the four way flashers. I can't tell you which one is which.

Past this point, check all the grounds for the turn signals. The wiring harness at the front will have one, or two leads, (Wires), coming out that bolt directly to metal. Either sheet metal for the car, or to the frame. These leads have flat, round terminal ends on them, with a hole in the middle of the terminal.

The lead's terminal end bolts can work loose causing a bad ground, and/or, there could be corrosion in-between the terminal end, and the area of metal it bolts to. If so, use sandpaper, and clean the terminal end, plus the area of metal it bolts to.

There are ground leads, (Or lead), that come out of the rear wiring harness also. Check these.

Still no?
Then your turn signal bulb sockets have corrosion in them. This causes a bad ground.

You may be able to use a rolled up piece of sandpaper, and clean the socket.
(Also touch up the lead, {LED. As in the metal lead}, contact point in the middle of the socket. This is for the Positive connection, but it doesn't hurt to clean it while you're there.

After this is the turn signal switch in the steering column.
(My money is on a bad flasher unit)

Jul 14, 2009 | 1995 Pontiac Firebird

1 Answer

GS400 Radio and etc.


check all the fuses.the radio is designed to stay on until you open the door once the vehicle is shut off ,so the radio and the locks are linked together.there is a low current 7.5 amp fuse or very close to that

Jun 14, 2009 | 2000 Lexus Gs 400

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...