Question about 1998 Oldsmobile Cutlass

1 Answer

Instrument cluster gauges

My 1998 Oldsmobile Cutlass's gauges are all not working. the tachometer, odometer, speedometer, temperature and gas gauge all remain at 0 whenever I start the car. What is the problem and how should i go about fixing it? I do know that the seatbelt light does turn on with the cluster and lights up, as well as my turnsignals, so I don't know if it is a wiring issue or there is a even bigger problem at bay

Posted by on

  • Denis Houle
    Denis Houle Aug 14, 2013

    check gauge fuse.he's there any other gauge ,fog lights connect to gauge fuse???

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 12,467 Answers

Check engine light ,abs , air bag lights etc.... come on when key turned on ?
Fuse IPC/HVAC BATT 10 amp located in the left IP junction block . Do you know where this junction box is ?
Does the heater an A/C work ? If so the fuse isn't the problem .
Speedometer
The speedometer is a road indicator. The vehicle speed sensor (VSS) is a permanent magnet generator which is located on the transaxle. The VSS sends an input to the PCM whenever the transaxle differential carrier turns. The PCM then buffers the VSS signal. The PCM transmits the VSS signal to the following components at 4000 pulses/mile through CKT 817:
• The instrument cluster
• The cruise control module
• The radio (uplevel)
The instrument cluster uses the input in order to indicate the vehicle speed on the speedometer.
Instrument Cluster Indicators
The BCM controls the instrument cluster indicators through the SPI serial data communication bus. Refer to Body Control Module System Check in Body Control System.

IPC/BFC ACC
10A
Instrument Cluster and Body Control Module (BCM)
IPC/HVAC BATT
10A
Instrument Cluster and Heater A/C Control Assembly

Posted on Jul 24, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 328 Answers

SOURCE: none of the instruments in

check the fuses

Posted on Dec 31, 2008

mackinbeats
  • 46 Answers

SOURCE: Speedometer and Tachometer not working

check the vehicle speed sensor located on the transmission housing.

Posted on Apr 11, 2009

  • 2 Answers

SOURCE: My gauges(temp, speedometer, tachometer, fuel,etc.) do not work

I believe that this is caused by a blown Relay or Fuse. I also just went through this. I took my Relays into NAPA and replaced them all, refered back to the diagram and installed the new ones, I also, (unsure if it'll make a difference) turned every fuse to face upright and in the same direction after removing to clean the contact point with a soft tipped metel brush. Overall, replace the Relays and you should be fine.

Posted on Apr 26, 2009

redds55
  • 2620 Answers

SOURCE: Speedometer, gas gauge, rpm, all not working while

These instrument clusters are known to be faulty.Replace cluster

Posted on May 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1998'Ford Explorer and half the dash lights are out and all pod a sudden my speedometer just quit. Need to know what fuses would go to these, so I can try that. Ty


Sorry but it's not a fuse problem . There is not a fuse just for the speedometer . The microprocessor inside the instrument cluster determines where the speedometer needle points , just like the fuel gauge , tachometer etc... Having the vehicle checked for DTC'S would be the proper step to take .
Vehicle Speed Signal
The vehicle speed signal is generated by the rear anti-lock brake sensor and sent to the 4-wheel anti-lock brake system (4WABS) module. The 4WABS module sends the vehicle speed signal via circuit 679 (GY/BK) to all systems which require a vehicle speed signal input.
Speedometer
The electronic speedometer receives a speed signal from the 4WABS module.

  • The Speedometer/Odometer Is Inoperative
  • Circuitry.
  • Speedometer.
  • GO to Pinpoint Test E .

No where in this factory diagnostic step does it say to check a fuse !

PINPOINT TEST E: THE SPEEDOMETER/ODOMETER IS INOPERATIVE CONDITIONS DETAILS/RESULTS/ACTIONS E1 CHECK THE VOLTAGE TO THE INSTRUMENT CLUSTER
Instrument Cluster
Measure the voltage between instrument cluster C288-7, circuit 1001 (WH/YE), and ground.
  • Is the voltage greater than 10 volts?
Yes GO to E2 .

No REPAIR circuit 1001 (WH/YE). TEST the system for normal operation.
E2 CHECK THE INSTRUMENT CLUSTER PRINTED CIRCUIT
Instrument Cluster
NOTE: Measurements must be made to the speedometer gauge pins that are inside the instrument cluster printed circuit clips.
    Measure the resistance between the speedometer pins (which can be seen in the middle of the instrument cluster printed circuit clips) and the corresponding instrument cluster terminal. Refer to the table for the pin and terminal assignments.
    Instrument Cluster Terminal Speedometer Gauge Pin C286-13 C287-1 S C287-2 G C288-7 BATT
    .

  • Are the resistances less than 1 ohm?
Yes GO to E3 .

No INSTALL a new instrument cluster printed circuit. REFER to Instrument Cluster Printed Circuit . TEST the system for normal operation.
Your best bet , take it to a qualified repair shop

Mar 30, 2017 | Cars & Trucks

3 Answers

My speedometer works but my digital odometer does not work on my 2003 old alero


This is one guy's advice: Replace the speedo head, that should take care of the problem."

This site is also interesting because the guy said
General Motors cars had instrument cluster problems from 2003 through 2006. When I researched instrument cluster problems on the Internet what I found raised concerns in me. Many of those vehicles had problems that began with the instrument cluster, but eventually led to the engine refusing to start.
(an electronic instrument cluster, digital instrument panel or digital dash for short, is a set of instrumentation, including the speedometer, that is displayed with a digital readout rather than with the traditional analog gauges. Many refer to it simply as a digital speedometer.)

http://www.instructables.com/id/Erratic-Instrument-Panel-on-GM-Cars/

Feb 12, 2017 | 2003 Oldsmobile Alero

1 Answer

98 Park Avenue Instrument Cluster Stopped working


Always check your fuses first to see if they are blown.

Jan 27, 2013 | 1998 Buick Park Avenue

2 Answers

Where is cluster for speedometer lights


The "cluster" means all of the things you see under the plastic cover in front of the driver, the 'gauges'. The term is a reference to the 'instrument cluster' including speedometer, tachometer, fuel gauge, idiot lights, temperature gauge, everything.
Get a second independent opinion since this is very unusual. Most likely you have a blown fuse.

Aug 26, 2012 | 1998 Cadillac DeVille

1 Answer

Changing dashboard light


Hi,

This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Aug 09, 2010 | 1998 Plymouth Voyager

3 Answers

Speedometer, gas gauge, odometer, rpm gauge not working


My gas guage, speed odometer and tempiture does not work
The speed odometre is reading 9999999 what should i do

Jul 29, 2009 | 1998 Nissan Frontier

3 Answers

2003 F-250 instrument cluster...


it sounds like you are getting a surge of voltage from your alternator/generator. Very strange.

the dealer can run a diagnostic test & pull fault codes or you can try this. If this helps, please report back & rate as fixya. Thanks. I am curious what you find as root cause. Good luck.

Instrument Cluster Self-Diagnostic Mode
To enter the instrument cluster self diagnostic mode with the engine off, depress and hold the odometer reset button. Turn the ignition switch to the RUN position and hold until the gauges sweep (within five to eight seconds). Depress the reset button once to advance to each stage of the self-test.
Turn the ignition to the OFF position to exit the instrument cluster self-diagnostic mode. If no DTCs related to the concern are retrieved, proceed to the Symptom Chart to continue diagnostics.


Instrument Cluster Self-Diagnostic Mode Odometer display Description GAGE Carries out gauge sweep of all gauges, then displays the present gauge values. Also carries out the check sum test on ROM and EEPROM. All segments illuminated. Illuminates all odometer segments. bulb Illuminates all micro-controlled lamps and LEDs. r #### Returns to normal operation of all micro-controlled lamps and LEDs and displays hexadecimal value for ROM level (used when requesting assistance from the hotline). nr#### Displays hexidecimal ROM level and type as stored in non-volatile memory (NVM). EE ## Displays hexadecimal value for EE level (used when requesting assistance from the hotline). dt #### Displays hexadecimal code for the final manufacturing date. ###C Gas engines display last temperature gauge input value from SCP, temperature gauge will indicate present temperature. Diesel engine displays present temperature analog/digital input in decimal as a ratio, temperature gauge will indicate present temperature. dtc #### Displays a 16 bit DTC in hexidecimal format. DTCs displayed are those detected in continuous operation not during self-test. EnG Displays English speed value being input, speedometer will indicate present speed. m Displays metric speed value being input, speedometer will indicate present speed. tAc Displays the tachometer value being input to the instrument cluster. Tachometer will indicate present rpm. FUEL Displays the present analog/digital fuel level being input to the instrument cluster as a ratio. OIL Displays the last analog/digital reading of the oil pressure switch contact resistance, oil gauge will indicate present level. br Displays the brake fluid level in an analog/digital ratio value. bAt ##.# Displays present battery analog/digital voltage. rhEo Displays present hexadecimal pulse width modulation (PWM) dimming input. rhi, rhS, rho Alternating 1 second display of pulse width modulation (PWM) input duty cycle, SCP hexidecimal dimming step, output driver counts in hexadecimal. Cr RUN/START sense circuit check. PA, Pb, PC, and Pd Displays 8-bit hexadecimal value for the Port A, B, C, and D readings (used when requesting information from the hotline). PE0-PE7 Displays 8-bit hexadecimal value for the Port E0-Port E7 in analog/digital readings

Jan 26, 2009 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

Speedometer/ Fuel Gauge & Tachometer not working


check for loose connection at the instrument cluster.

Jun 28, 2008 | 2001 Volkswagen Beetle

Not finding what you are looking for?
1998 Oldsmobile Cutlass Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...