Question about Cars & Trucks

1 Answer

Ford F100 brake diagram

Gday i'm just chasing a brake line diagram for a 1970 ford f100 showing everything in the braking system, I am looking to make up brake lines that have been stripped out of a project truck from scratch

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I have a 2004 kia sedona that will not start been told its immobilzer in key

Posted on Jul 26, 2013

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 426 Answers

SOURCE: 1976 ford f100 pickup 2wd

The brake bias valve can cause your symptom.Are the outer part of the brake calipers able to slide in and out freely .Jack it up take a wheel off and get someone to push on the brake pedal while you check for correct movement.Lube the slides so it is easier for calipers to return.a chunck of 4x2 wood is useful if you find them too hard to move by hand

Posted on Oct 09, 2008

  • 30 Answers

SOURCE: transmission for a 1978 Ford F100

c-6 trans! I have owned many ford trucks and the c-6 was needed.

Posted on Oct 30, 2009

  • 177 Answers

SOURCE: 1987 Ford Bronco. Looking for a brake line

1987 Ford Ranger Manual - Free Download | PDF Service Manual

Posted on Jun 18, 2010

  • 66 Answers

SOURCE: How do i wire up

Hey! One of my favorite projects here. The simplest way to go. First you need to make sure the wireing harness is setup for TFI system. It should have a couple big connectors by the driver side fender well in the engine bay. You will need a TFI module. Next you can use the original distributor or buy a new electronic one. If you use the original you have to buy a new stator and cap. I also recomend a new coil and preferably get rid of the balast resistor. This should complete your project.

Posted on Sep 06, 2010

  • 2422 Answers

SOURCE: will power steering from a 1979 ford f100 fit on

It should however you may need to use the mounting bracket from the 79 there bolth 302 ;s it should work

Posted on Nov 05, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What rear brake backing plates can i put in a 1956 ford f100?

check around as some sedans have the same rear brake setups as the f100. Cruise the wreckers (ford specialists) with your backing plate and find a backing plate same as yours from any sedan around the same year as yours.. Brake capacity is calculated on vehicle weight and as manufacturers are reluctant to spend money on developing new brake systems they tend to use the same parts on as many different models as possible.. Another thought car manufacturers use brake systems built by brake specialists like Bendix and Ferrodo and others so check other makes (dodge,chrylser even the chev range for a possible match of brake assemblies in that year.

Sep 08, 2014 | Cars & Trucks

1 Answer

1970 Ford F100 Gas Gauge Not Working

It may be the sending unit in the tank that needs replacing. Here's how you can check: Turn the key on and disconnect the sender unit at the gas tank. Ground the sender unit's wire with a jumper wire from the truck's harness to ground. Watch the gauge. If the gauge on the dash is good, grounding the sender wire will cause the gauge needle to react and should move to full. This would indicate a new sending unit is required. If the gauge doesn't move when the sender unit is grounded, the gauge is bad and needs replacing. Pull the instrument cluster out to replace the gas gauge. Likely any old ford gas gauge might work-back then, there were not so many production changes.

Nov 14, 2012 | Ford Cars & Trucks

1 Answer

Fuel Gauge Not working on 1970 Ford F100

check to make sure you have power going to sending unit on the tank,if yes,make sure you have a good ground.check all connections.As long as the float has not broke off the sending unit inside the tank, you should be able to fix it easily

Nov 14, 2012 | Ford Cars & Trucks

1 Answer

Looking for a 1955 ford f100 manual

always check ebay and do a google search first

Jun 22, 2011 | Ford F-100 Cars & Trucks

1 Answer

How do I remove the rear brake drum on my 1970 Ford pk tk F100?

on back side of drum is a slot at the bottom of backing plate they have a tool to do this or screw driver will work too. loosen brake maybe still have to hit drum w/hammer to break loose then drum will come off..

Jan 02, 2011 | Ford F-100 Cars & Trucks

2 Answers

I have a 1970 Ford pk truck F100 and I am trying to remove the rear brake drum. Cant seem to find a diagram to show me how it comes off. I see two holes that would make one think it needs twisted off. ...

It pulls straight out once the wheel is off. Sometimes there are little flat spring steel clips on one or more wheel studs- look for these before fighting with them.

Sometimes, with drum brakes, they will be worn to where there is a groove in them with a high spot at the inner edge of the bore (next to where the shoes contact the drum). When this is the case it's easiest to back the adjusters off before trying to pull the drum, as the shoes can be adjusted so far out that they won't clear the inner edge of the drum.

Other than that it's just a matter of tapping, wiggling and swearing. You'll get it, no worries.


Jan 02, 2011 | 1981 Ford F 100

1 Answer

Will power steering from a 1979 ford f100 fit on 1970 ford f100 , both has 302 engine ..

It should however you may need to use the mounting bracket from the 79 there bolth 302 ;s it should work

Nov 05, 2010 | Ford F-100 Cars & Trucks

1 Answer

Ned to now wat the firing order for dist cop shood be for a 1987 ford f100 pick-up truck 300sixcylender stick shift model#333

The F100 ended in 1983, so there is some confusion on your 1987 Ford F100. The F150 started in 1983 and was available in 1987, but not the F100. You have this listed under the 1981 Ford F100 category.
The 300 CID = 4.9L In-Line (Straight) 6-Cylinder.
In order to best answer your question I have included both the 1981 F100 4.9L and 1987 F150 4.9L below. The only difference is with the Distributor Cap Configuration and Connections.

For the 1981 F100 300cid=4.9L:
Firing order:

For the 1987 F150 300cid=4.9L:
Firing Order:

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at!

May 07, 2010 | 1981 Ford F 100

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

359 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides