Question about Cars & Trucks

Open Question

Mazda sting We did the front and back brakes, there was no brakes, we replaced the one steel pipe thingy at the left back wheel as the brakefluit was leaking there, still the brakes was very low, then we saw on the right back wheel the siliner thingy is also leaking, we bought a new one and replaced it, last night there was no brakes again, and the brakefluid light came on, as we checked we saw that very same silinder thingy was leaking again, what cane

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tripletauto
  • 1450 Answers

SOURCE: Right front wheel/disc brake? heat up

most likely a brake line causing problem. it is either the rubber hose or caliper sticking. the rubber hose will collapse and cause pressure to stay on the caliper

Posted on Nov 14, 2008

66 chrgr
  • 1011 Answers

SOURCE: steering creeks when turning left or right. front wheel noise.

humming noise is bearing.creaking is either tie rod or other ball joint.tie rods on these go out all the time.bearing also

Posted on Jan 25, 2009

  • 31 Answers

SOURCE: 1989 K-1500 Brake Problems

Did you replace your front brake lines as these are rubber and after time collapse causing the truck to pull in the opposite direction! In your case I'd say left front is crimped and blocks fluid and makes right front pull to the right. This is a common problem and one of the first items to replace on these trucks and at $30 cheap insurance.(REPLACE BOTH).

Posted on Mar 22, 2009

  • 91 Answers

SOURCE: 1998+ford van 150+brake lines+diagram

I only replace what is needed they are time consuming and all four breaks will need to be bleed only diagram is what you have under the van cut out the damaged section take it to parts store and get the size you need make sure you get all fitting at this time also good luck

Posted on Apr 28, 2009

  • 2 Answers

SOURCE: Brake light, Turn signal not working rear right 06' Focus

I have a 2000 ford focus no brake lights. with the brake lights the transmission would not go into drive .replaced the brake light switch checked fuse replaced turn signal switch with no results then i moved onto the wiper switch and replaced it as much to my supp rise it fixed the problems

Posted on Aug 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Video of how to replace rear wheel bearings of a Mazda 323, 1.3,sting,front wheel power


take the rear hub off
you will need a hydraulic press or a vice to push bearing out and then in.

Jul 09, 2016 | Mazda Cars & Trucks

1 Answer

Brake fluid is leaking along side the left front tire, from a small metal pipe.


hi fishin.... that small metal pipe is a brake line. you must replace that line immediately or you risk losing your brakes with no further notice

joe
thanks for choosing fixya

Jan 08, 2011 | 2001 Mazda Tribute

2 Answers

Where is the bleeder screw located on the back brakes, replaced the back brake line and need to bleed them and having issues finding the bleeder screw for the back.


Hi you know where the pipe goes into the back well the bleed nipple is located right next to where the pipe goes in, it might be covered in much so get a wire brush and brush all the **** off and you should find the bleed nipple locate right next to the part where the copper pipe goes in at the back.

let me know if you have any problems ok

plz rate this solution as i have a whole page of unrated posts, thanks

Sep 17, 2010 | 1996 Dodge Stratus

1 Answer

How do i replace front rotor in 2004 toyota sienna


1. Put your car on a level spot for safety and start your car Sienna.
2. For left front rotor, turn your steering wheel to the left all the way and stop the engine. DO NOT put emergency brake on! Put stopping blocks on the passenger front front, rear right and rwear left for safety.
3. Half loosen all front left tire nuts and jack up the left front then loosen all nuts and take the wheel off.
4. Use a 3" G-clamp from Lowes, Home Depot or any store near you, press against brake cylinder so that brake fluid flows back to its reservoir
4. Remove one bolt on the caliper and the other bolt loosen and lift the caliper with the other bolt on and rest on a block. Do not take the rubber hose off nor attend to loosen any brake fluid pipes and nuts.
5. Remove brake pads and remove the nuts on the rotor, done.
If you need further assitance please let me know and if this assisted you please feel free to rate the solution accordingly. Thanks, Midwest-tek

Aug 31, 2010 | 2004 Toyota Sienna

1 Answer

Pulls to left repaced brakes exchanged wheels and had realiegned still the same.


its either the flexible brake pipes are closing up inside ,very badly worn lower track control arm bushes or the ma ster cylinder but it depends if its a tandem front and rear or tandem one front and one rear ,another cause is a seized caliper -now was one tight to go back in when the new pads were fitted ??if so then it could be either the seal in the caliper has corroded in the seal seat path or again the flexible pipe ,if caliper goes in easy when the bleed nipple is undone then its the flexible pipe .their is nothing else that will cause this unless you have a badly worn disk but even so i have not had worn disks cause this but i have had a different carbon content in the steel of the disks before now but it is very rare ,i would go for the flexible hoses first as this is about 90% of the problems

Jun 06, 2010 | 1994 Chrysler Concorde

1 Answer

Goes in to four wheel drive but front tires are


Look at the back of the front wheels there is 2 black pipes, 1 for the brakes that conect to the brake unit (callipers) and the other one is the vacume pipe. Most of the time it is damaged. This pipe is softer and thinner than the brake pipe. It will have a inner pipe and outer sleeve (pipe) that is loose from the main pipe, just to prtect the inner pipe. It can have a leak under that sleeve. ENJOY from Willem Potchefstroom SA

Feb 27, 2010 | 1998 Kia Sportage

1 Answer

How do I replace the front brake pads on my 2009 Mazda 6 2 litre? Can I do it myself?


Step 1 Park the Mazda 6 on a flat surface. Put the emergency brake on and put wedges behind the wheels to prevent the vehicle from rolling. Disconnect the negative battery cable. Using a syringe, turkey baster or similar tool, drain two thirds of the brake fluid from the master cylinder. Remove the wheel.
  • Step 2 Remove the bolts attached to the brake pipe. Remove the bolt cap attached to the caliper top. Swing the caliper, pivoting it downwards. Suspend the caliper from the frame using mechanics wire. Remove the M-springs, the pads and the shims.
  • Step 3 Press the caliper pistons back into the cylinders. Install the brake pads. Lubricate the exterior of the pads using anti-squeal. Install the shims. Install the M-Springs. Reinstall the caliper. Using a torque wrench torque the bolt to 36 to 39-ft. lbs. Install the cap.
  • Step 4 Reinstall the wheels. Add brake fluid to the master cylinder. Bleed the brakes. Reconnect the negative battery cable to the battery. Start the engine and pump the brakes 3 to 4 times to seat the brake pads. Test drive the Mazda 6 at slow to moderate speeds to ensure that the maintenance was performed correctly.I hope this helps you and please have a merry xmas
  • Dec 18, 2009 | 2009 Mazda MAZDA6

    1 Answer

    I have a 1999 kia sportage four wheel drive and it will go into four wheel drive sometimes,you can hear it trying to kick in.the front drive shaft goes around all the time it is trying.it makes a faint...


    Vacume line is leaking and do not engaga fully. Vacume pipe an front wheels. 2 pipes 1 for brakes 1 for vacume. Pipe (rubber) connect by means of pushing it over the steel pipe. Easy to replace. Willem SA

    Feb 22, 2009 | 2002 Kia Sedona

    2 Answers

    Leaking brake line


    probably not the lines are usually attached to the frame rail behind the tank.

    Aug 25, 2008 | 1999 Dodge Durango

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    12 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...