Question about 2001 Nissan Quest

1 Answer

Replace driver side mirror on 2001 Nissan Quest

I have purcahsed a replacement driver side mirror for my 2001 Nissan Quest. Is there step by step instructions on how to replave the mirror?

Posted by on

  • 1 more comment 
  • cmhughes Mar 31, 2009

    I am replacing the entire mirror fixture.

  • K May 11, 2010

    are you replacing just the mirror, (if so see: www.burcoinc.com goto 'redi cut' then 'instructions') OR are you replacing the entire mirror head assembly?

  • Amr Radwan May 11, 2010

    is it just the glass part of the mirror or is it the whole mirror with the fixture ?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 4,387 Answers

SECTION 501-09: Rear View Mirrors 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Mirror —Exterior Rear View Removal

  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the upper speaker.
    1. Disconnect the electrical connector.
    1. Remove the bolts.
    1. Remove the speaker.
  1. Position the watershield aside.
  1. Remove the exterior rear view mirror access panel.
  1. Disconnect the exterior rear view mirror electrical connectors.
    • Release the wiring harness locator.
  1. Remove the exterior rear view mirror.
    • Remove the bolts.
    • Feed the wiring harness through the door opening.

Posted on Apr 24, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 375 Answers

SOURCE: need to replace drivers side mirror

not so difficult , there should be a piece of trim straight in from mirror on inside of door, remove trim behind should be nuts holding mirror on.

Try partstrain.com they sell aftermarket replacement parts, mirrors look like origionals but alot cheaper

Posted on Jun 24, 2008

bibleman01
  • 334 Answers

SOURCE: 2001 Infiniti QX4 low beam bulb replacement instructions

Look directly behind the headlight box if there is a rubber sleave covering the plug take it off. Unplug the wires from the bulb, there may be a saftey clip you will have to pry up to get it off.after you get the plug off the bulb holder should twist counterclockwise then it will pull right off.When you change the bulb just remember to wipe your body oil off the bulb before attaching it back into the headlight box. Then plug it back in and your in business. The high beam has three wires and the low beam has two wires. The bulb will have to be the right one.
God Bless You Greg

Posted on Nov 25, 2008

  • 4387 Answers

SOURCE: NEED TO REPLACE ALTERNATOR MYSELF

here's 96. should be the same. Be very careful not to overtighten any of the belts or you can break the snout off the crankshaft and ruin you engine.

Section 14-02: Generator, Integral Regulator — Internal Fan and Regulator Type 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Generator Removal

  1. Disconnect the battery ground cable (14301).
  1. Raise and support the vehicle.
  1. Remove the five engine and transmission splash shield bolts and two engine and transmission splash shield screws.




  1. Remove the RH engine and transmission splash shield (6775).
  1. Remove the wire harness bracket bolt.




  1. Remove the B-terminal insulator boot.
  1. Disconnect the generator electrical connector from the generator (GEN) (10346).
  1. Remove the ground wire nut from the generator and position the ground wire aside.
  1. Remove the B-terminal nut from the generator and position the B-terminal wire aside.




  1. Loosen the inner and outer generator-to-bracket bolts.


    61f4d2f.gif

  1. Loosen the generator locking bolt.



    93c9f65.gif
  1. Loosen the generator adjustment bolt.


    6e949fa.gif

  1. Remove the drive belt (8620) from the generator pulley (10344).
  1. Remove the generator locking bolt and washer.
  1. Remove the inner generator-to-bracket bolt and the two washers.
  1. Remove the outer generator-to-bracket bolt and the two washers.
  1. Remove the generator.
Installation
To install, reverse the removal procedure. Tighten the inner generator-to-bracket bolt to 23-26 Nm (17-19 lb-ft). Tighten the outer generator-to-bracket bolt to 23-26 Nm (17-19 lb-ft). Tighten the generator locking bolt to 16-20 Nm (12-15 lb-ft). Adjust the drive belt very carefully. Refer to Section 03-05 for the procedure.

Posted on Jun 17, 2009

  • 1986 Answers

SOURCE: Replace passenger side electric mirror

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Posted on Sep 29, 2009

  • 1986 Answers

SOURCE: replace passenger side mirror on 2008 Impala

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Posted on Sep 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver side power window stuck in down position - Nissan Quest 2001


I HAD THE SAME PROBLEM DIAGNOSE MOTOR OR SWICH MOSTLY BAD SWICH ,BUY ON LINE EASY TO CHANGE

Jun 03, 2012 | 2001 Nissan Quest

2 Answers

Need to replace driver's side mirror-1999 Nissan Quest


directly behind the mirror on the inside of the door there will be a plastic triangular cover, this cover will unclip with a little bit of prying with a flat blade.
Behind the cover you will see a few holes in the panel, in at least 3 of those holes you will see bolt heads, thes have to be removed but before you do there is a multi wire plug that you need to seperate if you have electric mirrors.
once the bolts are removed you should be able to remove the mirror

Jul 02, 2010 | 1999 Nissan Quest

1 Answer

The driver side window of our Nissan Quest Van won't go up. What trouble shooting tips do you recommend?


1st need check fuses for windows next check switch capability by switching up and down see if window will respond next check power to switch next check power to window motor if all ok replace window motor don't forget to check window rail make sure not jaming

Jan 18, 2010 | 2001 Nissan Quest

1 Answer

95 nissan quest front passenger side power window does


driver side switch is not working replace it

Oct 12, 2009 | 1995 Nissan Quest

1 Answer

I have also broke off my 2001 Nissan Quest sliding door handle on the driver side. Also the sliding door cannot be opened from interior... Any help is appreciated... Thanks


the child lock rod may have been extended...
open the driver side door, and with a skinny finger, push that child lock rod back in towards the rear of the sliding door
use the passenger side as reference
once you pushed it in, you can now open it from the inside handle

Oct 06, 2009 | 2001 Nissan Quest

1 Answer

Driver side motorized mirror on auto needs to be replaced


the whole asssembly or just the mirror glass?

Mar 23, 2009 | 2001 Subaru Forester

1 Answer

Replacing Nissan Altima 1998 passenger mirror


to replace it you have to open up the door take off the little plactic piece in the corner of the door,, then there is going to be 3 screws that you have to remove in order to remove the old one, just do the steps in reverse to replace the new mirror, i just had the same issue, but on the driver side.. good luck

Mar 18, 2009 | 1998 Nissan Altima

1 Answer

I need the location of fuel filter




Under hood, driver side, rear engine area, passenger side of master cylinder, mounted on firewall

Jan 10, 2009 | 2001 Nissan Quest

1 Answer

2001 Nissan Quest - Broken Exterior Sliding Door Handle


you can do this. you have to remove inside trim panel for access. if you still need to do, I will send you repair steps. let me know

Oct 16, 2008 | 2001 Nissan Quest

Not finding what you are looking for?
2001 Nissan Quest Logo

Related Topics:

1,271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

84540 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...