Question about Cars & Trucks

Open Question

Timing marks flywheel of gwm

Need to know how the timing marks for the gearbox sensor sits that works of the fly wheel

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

keemo68
  • 1263 Answers

SOURCE: correct flywheel installation '90 240 B230 w/5 SPD transmission

you should have index holes on the flywheel this is to keep the balance of the crankshaft of the motor. the sensor on the back is the knock sensor. your index hole on the flywheel should line up with the holes on the crank. in most instances they should only fit one way. also make sure you put the right side facing the engine. this is important other wise you won't be able to connect the trans and the starter won't match up right.....please rate..thanks

Posted on Sep 20, 2008

joecoolvette
  • 5660 Answers

SOURCE: need a picture or diagram of top dead center/86' honda prelude 2.

From what I see in my manual,

1.There is a Timing Pointer on the back of the engine. There is a White mark on the flywheel. The white mark must line up with the timing pointer, for Number 1 piston to be at Top Dead Center.

2.Facing the engine, looking at the camshaft sprocket. The sprocket has spokes. On one of those spokes is the word, "UP" in raised letters, or there is a small Dot. As you can see here, the spoke with the word UP goes -> Up.
(Same thing of course if it is a Dot, instead of UP)

On the back of the camshaft gear, (Sprocket), are marks. On the edges of the camshaft gear. These line up with the top edge of the cylinder head. The surface of the cylinder head, where the valve cover bolts down to.

I'm sorry, at present I do not have a website, that I could link you to for a diagram, or photo.

Posted on Aug 13, 2009

Testimonial: "thanks for the help. that fixed my problem"

jpstuhr
  • 49 Answers

SOURCE: 1983 civic 1500 timing

At slow idle and Before Top Dead Center, unless otherwise specified.

1981-89: Leave Distributor vacuum hoses, as equipped, connected.
a4d88ba.jpg ea4458f.jpg

Posted on Feb 12, 2009

ourhowse
  • 2007 Answers

SOURCE: fly wheel needs to be replaced

Yes you do. If it's 4x4, i find it easier to pull the motor.

Posted on May 04, 2009

  • 7353 Answers

SOURCE: lincoln ls flywheel

Big trouble. The trans has to come out to access the flywheel.

Posted on Dec 02, 2009

Testimonial: "ouch!!!! thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Isuzu trooper 2004 model 4jx1 engine what was the fly wheel marks if it was at tdc


if flywheel is fitted in correct position the timing mark on the front top cambelt gear is at 12 O clock and with starter motor removed you will see 3 lines stamped in the interuptor ring that is bolted to the rear of the flywheel if manual on early builds, also there is a notch in flywheel which you can see if gearbox is out this goes at 6 O clock
25312290-55d4lqh0wtq3cergg12nnjcv-3-0.jpg

Dec 07, 2014 | Isuzu Cars & Trucks

1 Answer

Flywheel position on nissan diesel 2.5


on the fly wheel. the bolt holes on one side will show where the fly wheel washers sat. if the tranny is out the way you can test fit it for both sides and see witch side lines up the best. and if there is factory paint markings on the fly wheel that is the side that needs to face the tranny.

Sep 03, 2014 | Cars & Trucks

1 Answer

Does anybody know what tue time frame is for replacing the clutch/flywheel on an 07 long wheel base citroen relay


If it is a diesel engine then the flywheel may have the timing injection mark in the front of the flywheel facing a hole and pointer in the bell housing . This will require that the fly wheel bolt holes will be slightly off and will require you to turn the flywheel hole by hole until the bolts all screw in finger tight.. If you are asking how long should the job take 4 to 6 hours in a well equipped shop.

Mar 20, 2014 | Cars & Trucks

1 Answer

I need the timing marks on the fly wheel on a 2.8d gwm steed


I want to do timing on my gwm steed after replasing my diesel pump

Aug 07, 2013 | Cars & Trucks

1 Answer

Installing piloet bearring in flywheel


Hi Snale, The bearing is located inthe center of the fly wheel. To gain acsess means removing the gearbox, clutch assembly and flywheel. Gain access from the back of the flywheel. Tap out the failed bearing, fit in the replacement and refit the flywheel. Make sure to torque the fly wheel bolts to the required specs. This is a major undertaking and even though the bearing is very small the job is very big. Regards John

Nov 16, 2012 | Cars & Trucks

1 Answer

I am tring to fix my fly wheel I think it's the fly wheel any ways I think there is a bolt loss where is the dam thing on this and anyways i just need a web site to be able to find it and how to take it...


Perhaps we are thinking of something completely different to each other. The flywheel sits slap bang between the engine and the gearbox and either, usually the gearbox, has to be removed to gain access to the flywheel. Here is a picture of what goes up to make up the flywheel and clutch assemblies, the flywheel is the part on the left and is bolted to the crankshaft through the six holes near the middle. Come back to me if you need anymore clarification.

images?q=tbn:and9gcsrvbgx14s0yhqqthg-bzqlsoqml2ols1fwh1yqkzcjco_gofjgy7v7qyu0

Apr 14, 2011 | 2001 Ford Focus

1 Answer

Are the threads on the nut for the crankshaft pulley left or right handed?


Hi they are normal nuts so will undo anticlockwise, but to undo this nut/bolt your going to need to lock the flywheel you can do this by either removing the starter motor and jamming a big screw driver in the teeth of the fly wheel so that it lock on the casing of the gearbox or you can undo an inspection panel on the gearbox to give you access to the fly wheel and then jam it that way other than doing this you would need air tools to undo this nut without jamming the fly wheel

May 22, 2010 | 2000 Nissan Frontier

3 Answers

Cltuch 97 excel


dont listen to them, easiest way is: remove air intake box(3 nuts)
remove nuts surrounding the outer gearbox(about 6) and then remove the gearbox mounts
lower the gearbox and move slightly to the drivers-side. best to put a block or jack under it. then take the fly-wheel off(marking where it sits against the clutch kit)
and then pull the clutch plate off, making sure all fingers are not bent. i picked up a full clutch kit 2nd hand for 25$

Nov 14, 2009 | 1990 Hyundai Excel

2 Answers

Fly wheel problem on a jeep


if its a 4JX1 diesel, yes it goes in 1 spot yet it can be bolted up in every location
put crank pulley timing mark to TDC can also check by removing cam belt top cover and check timing mark aligned up with mark at 12 O clock then flywheel has small notch in edge that must go at 6 O clock (facing down) look closely it is hard to see due to flywheel sunk into back of block.

Oct 19, 2008 | 2000 Isuzu Trooper

2 Answers

Isuzu trooper 3 litre diesell oo year!


with no1 at TDC mark is on balancer and can take off top cam belt cover to check that cam gear is timmed on mark at 12 O clock there is notch in edge of flywheel that should be put at 6 O clock (facing down) it is hard to see with flywheel on engine look closely

Oct 18, 2008 | 2000 Isuzu Trooper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...