Question about Hyundai Motor 2003 Elantra
The car shut off at the gas station it started back fine, then later on that day i went to the store and when i came back out it didn't start.AAA said it was a starter i had that replaced still no crank no start. please help
You had a starter replaced,paid for that,
even though nothing works,not even
the new starter?
Where did you go for that work?
AAA- didn't know they diagnose vehicles
& give advice,you been had by two parties
Posted on Jul 26, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
its the camshaft position sensor . Its located (atleast on my 1.6L) to the right of the front HOT plate the conection runs between the engine and the right side fan. easier to work on if you take off the air intake thats by the left front side of the battery. you will be working between the fan and the motor. only one bolt but is tricky so u need a 1/4 inch nuckle with a 1/4 extention. once located and you have the right tools it will only take 30 minutes to replace....dont forget to take off negative battery cable before you start.
Posted on May 07, 2009
did you pick up a fault code to explain your action as i dont believe the oxygen sensor is at fault.it might be that one of your other sensors is at fault.the 02 sensor only reads the emmition gasses but will not cut the engine.plse get the fault codes.
Posted on Jul 16, 2009
have it scan to check camshaft sensor and crankshaft sensor.and pcm.all 3 can cause no spark and no fuel problems.
Posted on Jul 20, 2009
HI, MY NAME IS JAVIER
I GET THE SAME PROBLEM ( NO SPARK) BUT MY CAR IS 2003 HYUNDAI TIBURON GT V6 I CHANGE THE HEAD GASKET AND THE TIMING BELT AND WHEN I START DE ENGINE DOESN'T WORK (NO SPARK) I CHANGE MY CAM SENSOR AND I CHECK THE CRANK SENSOR, I TAKE OUT THE COMPUTER AND I CHECK THE WIRES AND " I FOUND THE PROBLEM"
THE PROBLEM IS THE CONECTOR FOR THE (O2) OXIGEN SENSOR LOOKS THE SAME FOR THE CONECTOR COILS AND THOSE ARE VERY CLOSE
SO, I WAS CONECTED THE COIL CONECTOR TO THE (02) OXIGEN SENSOR
IF THIS SOLUTION IS FINE FOR YOU JUST LET ME KNOW
Posted on Sep 29, 2011
Tips for a great answer:
Oct 19, 2014 | 2003 Dodge Grand Caravan AWD
Oct 25, 2012 | 2005 Pontiac Grand Am
Jul 23, 2011 | Hyundai Tucson Cars & Trucks
Aug 09, 2010 | 1993 Dodge Colt
not starting or turning over indicates towards multiple possibilities. It can
be issue with battery or weak battery. But if battery checks out ok, then it
can be starter issue or faulty alternator or problem with low fuel pressure or
no spark at spark plugs due to dirty spark plugs or faulty ignition
coil or injectors getting cracked or dirty and needs to be cleaned.
confirm the problem, the basic troubleshooting is required.
this link below and follow the troubleshooting:------
This will help.
Dec 14, 2009 | 1990 BMW 3 Series
Jul 13, 2009 | 2003 Hyundai Santa Fe
May 28, 2009 | 1999 Chevrolet Tahoe
Jan 02, 2009 | 1995 Ford Taurus
84 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: