Question about Cars & Trucks

Open Question

Where is the obd connector located in a Hyundai galloper v6 2001

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: Where is the On Board Diagnostic (OBD) connector on the car.

It is under the dashboard, driver side. White, oblong female connector. One row of pins not as long as the other.

Posted on Sep 17, 2008

Ad
  • 231 Answers

SOURCE: 1997 SUZUKISIDEKICK OBD LOCATION

it should be located within 12 inches of your steering wheel under the dash, so that you can see it from a kneeling position r it may be located behind the ashtray. Yes on some makes and model you need to remove the ashtray. The connector is a16 pin lug in.
Good luck

Posted on Oct 20, 2008

tjcanno
  • 16 Answers

SOURCE: Location of connector for OBD tester

Inside van, in driver's seat area, to the right of the steering column, under the dash. It is to the far right under the dash, next to the center section that goes down.

Posted on Dec 28, 2008

sidlas
  • 95 Answers

SOURCE: OBD II Connector identify and location?

2004 Chevy Aveo LS, the OBD-II connector is against the panel closest to the driver's knees above the brake pedal.

Posted on Jun 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the OBD connector located in the 98 elantra sedan located


Under the dash, on the left side of the steering wheel. About where your left knee is when sitting in it.

Oct 20, 2014 | 1998 Hyundai Elantra

1 Answer

The engine warning light came on today


i am working on a galloper 1997 but cant find the dlc (obd connector)

Apr 01, 2013 | 2002 Hyundai Galloper

1 Answer

Please tel me where is the place of serial number to hyundai galloper 1996


Try looking on the front drivers side door, where it is metal. Open the door and look down on the side of the door jam. It should be there.

Feb 17, 2011 | Hyundai Excel Cars & Trucks

1 Answer

Where can I buy a water pump of Hyundai Galloper 1999-2000 model Engine - D4BXN or its alternative products that fit the car or model. Please help?


the only information I could find on that engine is that it is apparently a Mitsubishi product, you might try locating a part number on the water pump, that would be very beneficial, then you could google the part number or even take it to your local parts store and have them locate it.

May 28, 2010 | Hyundai Motor 2000 Tiburon

1 Answer

What should the tyreressurs be on the Hyundai


it will be in the owners book but 32-40 psi

Jul 16, 2009 | 2003 Hyundai Santa Fe

1 Answer

OBD II Connector identify and location?


2004 Chevy Aveo LS, the OBD-II connector is against the panel closest to the driver's knees above the brake pedal.

Jun 13, 2009 | 2004 Chevrolet Aveo

1 Answer

DLC communications with OBD not possible


OBD II connector troubleshooting 101

I had the same problem with my 2000 Elantra. the OBD II connector pins get squished and won't make cantact with the scan tool, therefore no connection. the solution is to bend the pins back so they will connect to the scan tool.


FIRST! check your lighter and radio fuses (which you have already done). If possible, make sure your scan tool is working properly, try it on another car. If it is functioning properly, remove the 2 screws holding the obd II connector to the dash. Look for obvious signs of corrosion, damage, or stuff that shouln't be in the connector (rocks, gum, etc.) clean the connector with a good electronics cleaner (I use the CRC stuff), you can usually find it at you local parts store, radio shack, or even wal mart. hose down the inside of the connector thouroughly and allow time to dry.

check for voltage between 4 (gnd) & 16 (+vcc) then 5(gnd) and 16(+vcc) with the ignition on the voltage should be between 12v-16v (these pins may be different on other cars, look for an OBD II connector pinout diagram if your car is different). If this voltage is not present at either pin, the problem is not the connector. check your fuses and wiring. if this voltage is present at both pins continue.

Here's what I did. with the connector free from the dash, you can see the back of the connector where the wires enter the connector. on either side of the connector there may be a white clip. pop both of them off. you should be able to push a small screwdriver or pick in that space to pull the pins back out towards the outside of the connector. do one at a time so you can tell if the pin has moved back out into position. do this for all of the pins. Try to connect. if still no luck try again to push out the pins and reconnect.

If your connection is restored, replace the clips, screw it back into the dash. Return your car to the lousy DMV where they will proceed to tell you something else is wrong which they neglected to tell you on your first 10 visits!! :-)

Stuff thats good to know:
some auto parts stores will connect their OBD II scan tool to you car for free. auto zone is one place
some times the computer will need to reset to restore a connection to the scan tool. to do this simply cycle the ignition off (wait a few seconds) then on again.
online auction places are a excellent resource for USB to OBD II connectors to connect your laptop to your car. there is lots of OBD II diagnostic freeware out there to go with your newly purchased connector.

Good Luck

Chris
-CL Systems

Jan 28, 2009 | 2000 Hyundai Elantra

1 Answer

Connector I got you answer


On the 1999 Hyundai accent that I worked on the OBD II connecter is on the left side of the steering wheel. It faces down and is located above the pocket/ dimmer control. I hope this helps

Jan 21, 2009 | 1999 Hyundai Accent

1 Answer

Cant find a connector for my 1999 Accent


THE 16 PIN OBD SOCKET IS UNDERNEATH THE STEERING WHEEL SHOULD BE VISABLE IF YOU LOOK UP FROM UNDERNEATH AS IF YOU WHERE LOOKING AT BACK OF INST.PANEL.

Jan 21, 2009 | 1999 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

973 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...