Question about Cars & Trucks

1 Answer

Have replaced all tie rods; inner&outer;struts&upper mounts;sway bar bushings & links;lower control arms with ball joints& passenger side upper motor mount.none of these have changed this noise even s

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,256 Answers

What noise? And year and make of car?
A clicking noise on turns is a worn CV joint on the axle shafts. A grinding noise at one of the wheels could be a wheel bearing. Worn brake pads may cause squealing, screeching other high pitched noise.

Posted on Jul 25, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2003 Dodge Caravan Front end clunk.

Had similar problem with 2003 Dodge GC. Replaced the parts you mention + rack & pinion, then to fix the now noticable whining noise, replaced power steering pump and pulley. Fortunately was under an extended warrentee at 46k miles.

Posted on Jul 19, 2008

ftw1952
  • 10319 Answers

SOURCE: step by step instructions for

you will need to split off the idler arm's shaft from the center link after you remove the nut and cotter pine with a fork slitter then undo the bolts from the frame from the idler arm

the sway bar bushings are removed by taking off the two blots from each bracke holding the in place onto the bar

the ball joints are riveted in place on top which will need to be ground off..the rivet heads that is
the replacements are bolted on

the lower ball joints are pressed in so a ball joint press is needed
see if any local auto parts store rents this tool such as Auto Zone

Posted on Mar 20, 2011

jstreetunlim
  • 1 Answer

SOURCE: front suspension rattles on not

This is an easy one! These vans had a lot of problems with intermediate sway bar bushings. They are fairly cheap but a bit of a pain to change if you don't have a hoist as they are way under the van behind part of the front cross member. I would phone around and get a couple of quote from local shops, it should cost about $150. parts and labor. 9 times out of 10 the bushings are all you'll need.
Here's a link to the same job:

Posted on Sep 22, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Front driver side leaning inward, have changed strut,etc...


Upper and lower ball joints. Control arm bushings bad. or both.

Jul 09, 2016 | Cars & Trucks

2 Answers

Car shekes when hit bumps


Check for bad wheel balance, struts, lower ball joints ( no upper joints) , outer tie rod ends, inner tie rod ends, stabilizer bar bushings, lower control arm bushings , and finally a wheel alignment ,you have some bad looseness in one or more of these front end parts. GOOD LUCK FRIEND.

Mar 15, 2015 | 2001 Dodge Intrepid

1 Answer

WHAT ELSE SHOULD I CHANGE WHEN I AM CHANGING REAR STRUTS ON 94 CAMRY


On the struts, it will depend a bit on what you find, but I would also replace the bounce buffers, upper and low spring seat rubbers and maybe the strut upper bearing plates if they have been noisy at all. They do wear.

Have a close look at the bushings in the lower lateral arms and the torque rods (drag links). I would replace the sway bar mount bushings as they are notorious on this car for wearing quickly.

http://www.turboninjas.com/camry/sa.pdf

May 22, 2012 | 1994 Toyota Camry

1 Answer

How do i change my rubber bushings on the front suspention of my 1997 dodge ram 1500


opper Control Arm Bushings
  • To access the upper control arm, remove the shock absorber and the strut bar. Also, disconnect the sway bar from the lower control arm, if your particular Ram model is equipped with it. After that, you can hold the coil spring in place with a spring compressor.
    Secure the wheel hub assembly to the chassis using a wire before you disconnect the upper ball joint. This will prevent damage to the brake hose. When ready, release the ball joint using a ball-stud loosening tool (see Resources).
    The upper control arm mounts to the chassis with a cam bolt assembly. Once removed, you can place the control arm on a vise and remove the bushings using a bushing service tool (see Resources). When installing the new bushings, do not use any lubricant but make sure the flange on the bushing end seats properly on the arm bore. Then re-install the upper control arm. When finished, take your Dodge vehicle to a good shop to align the front suspension.
Lower Control Arm Bushings
  • Remove the shock absorber and strut bar. If your particular model is equipped with a sway bar, disconnect it from the lower control arm.
    Secure the coil spring with a spring compressor and release the lower ball joint from the wheel/hub assembly using a ball stud loosening tool (see Resources).
    Now you can release the lower control arm by removing the rear mounting bolts. Remove the bushings with a bushing service tool (see Resources). When installing the new bushings, do not use lubricant and make sure they seat properly on the control arm bore. Then replace the lower control arm. When finished, take your Dodge vehicle to a good shop to align the front suspension

Oct 20, 2011 | Cars & Trucks

1 Answer

Rattling noise from near side front wheel area. Have checked for play on bearing and checked brake disc. No problem detected. Noise only occurs at low speeds.


i have the exact same problem ive got 2001 honda civic and have an annoying rattle from the wheel area. i have replaced cv joint, ball joint, sway bar drop links, strut, and suspension bushing and arm....but still rattle noise is there. dnt have a clue what it could be, from looking on the internet i have found few possibilities.....lower control arm/bushin...motor mounts....gear box mounts....strut rod bushing....axle....inner/outer cv joint....calliper pins......shock/shock bushing...or wheel bearing. im hoping tio get all this checked out its got to be able to be fixed somehow!

Dec 29, 2009 | 1997 Volkswagen Golf

1 Answer

How to replace right front axle 2000 buick lesabre


Lift the passenger side of vehicle. Remove tire/wheel assembly. Remove the axle nut. Remove the tie rod end nut. Smack the side of the housing the tie rod end goes into to pop the tie rod end loose and out. Remove the sway bar link. Remove the lower ball joint nut. Smack the housing the lower ball joint goes into to pop the ball joint loose. Pry the lower control arm down to pop the ball joint out. swivel the rotor and strut assembly to the side. Pop the axle out. Reassemble in the reverse order.

Jul 05, 2009 | 2000 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...