Question about 2000 Ford Ranger SuperCab

Open Question

Dashboard removal I want to replace a broken power outle

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Venting


Hi. I'm understand you are talking about the A/C.
IF yes.
The first step is.
Check the vaccum line suply.
Because all the actuator work with vaccum.
Remove the A/c control panel, check if there a vaccum
If you found vaccum. Chack for leak. at any of the outles.
Because if one of the outles leak . the rest don't will work.

I can send a vaccum diagram if you give me the especific engine size on your car.

I hope this information work for you.

Jul 14, 2008 | 1986 Chevrolet Camaro

1 Answer

2012 Durango. Heat coming out of driver side only. Blows cold air on passenger side and rear. Fluids fine. Any ideas?


Blend door broken inside heater case assembly need to remove dashboard to remove case to split case apart to replace

Jan 01, 2015 | 2012 Dodge Durango SXT 4dr SUV 3.6L V6 FFV...

1 Answer

My nissan rouge will not back up


Transmission goign outl Try having the filter changed and oil replaced.

Jul 02, 2014 | 2010 Nissan Rogue

1 Answer

Dash board lights don't turn on wat could be the problem


get ready to work upside down, first get an electrical diagram of your dashboard, find the power wire, get a paperclip and uncurl it, stick it inbetween the power wire and its holder (so the paperclip touches the copper of the wire). next turn the key to the on position, and turn on the lights. (make sure you do this briefly because it will drain your battery) then get a DVOM or a test light, ground them, and see if your dashboard lights are getting power by sticking the lead onto the paperclip. if it is then there is something wrong with the lights themselves. if not, check to see if your power wire is broken, chaffing, shorting, anything wierd. if its not broken then bring to the dealership. if it is broken then replace the wire. 

i do not own a jeep so i cannot tell you exactly how to take apart the dashboard (if the lights are bad) but if you dissasemble it from bottom to top slowly and carefully you should be able to access the lights.

Hope this helps!
                       Joe.

Feb 06, 2010 | 1995 Jeep Grand Cherokee

1 Answer

Dodge ram 1500 power steering


your insurance company should take care of the repairs or his whomever was at fault either way either the power steering casing is broken causing a leak or a break in the line itself or the belt snapped open the hood and visually look and see what is leaking or the tire could even be rubbing at times without seeing it i cannot say for sure ....but let me know what you discover

Sep 24, 2009 | 2000 Dodge Ram 3500

1 Answer

My dashboard lights don't light up


it must be a blown fuse for the dashboard lights. you can check the owner's manual or do a physical inspection of the fuse box under the hood/bonnet of your jeep.
Remove and hold up to see if the fuse link inside is cut or broken.

Simply replace with fuse of appropriate rating please.

Jul 08, 2009 | 1999 Ford Expedition

1 Answer

Remove dashboard panel from yukon 2001


gonna replace a broken off antenna base on a 2001 yukon xl , I was able to take out the vent, handle bar the screws on both side panel of the dash board still cant lift up the dashboard

Jun 05, 2009 | 2002 GMC Yukon XL

2 Answers

How to replace bulbs for ac/ heater control unit


1. Remove the dash around radio (just clips)
2. Remove 2 screws pointing up . (You do not need to remove screws which are parallel to the floor)
3. Remove screw pointing up on the bottom of the dashboard on left side of the driver (near left leg).
4. Remove 2 screws pointing up in the instrument cluster area.
5. Put car in 1st gear and gently remove black plastic surrounding instruments (it will have ait vents, so slide it carefully out not to damage foam insulation on air ducts; start on the bottom hear steering column) ; unplug connectors to clock and emergency flashers.
6. Remove 2 screws, now exposed, near instrument area, holding dashboard. (that was what I spent most time on, I didn't know about this screws.
7. Now gently remove (or move up) dashboard (around instrument cluster and heating controls.) Start next to ignition (careful not to damage the bulb next to the ignition.
Since you only need to get to the heating controls block, I only move up the dashboard next to it.
8. Remove 2 screws that hold the heating control and slide heating control out . This step is unnecessary If you totally removed the dashboard.
9. Pull out lever controls for fan speed, zone and temp
10. Use the screwdriver (flat) to pry 2 plastic tabs on top and on the bottom of heating control so black cover can be remover.
11. You did it! two bulbs are going to be under the cover.

May 19, 2009 | 2001 Toyota Sienna

Not finding what you are looking for?
2000 Ford Ranger SuperCab Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...