Question about Pontiac Cars & Trucks

1 Answer

Sucking sound braking

My brake cyclinder sucking in air

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Pontiac Master
  • 12,223 Answers

Go to www.automecanico.com translate this web with your browser and fix it.
God bless you

Posted on Jul 25, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 341 Answers

SOURCE: Nov. 94 Grand Cherokee Jeep no back brakes

I bet you still have air back there. If you didn't bleed the system after the master you need to do that. Bench bleeding a master doesn't always work.Also badly out of adjustment rear brakes can act the same way.

Posted on Nov 26, 2008

  • 79 Answers

SOURCE: excessive brake pedal travel

pump the brakes a few times they should stiffen right up

Posted on Mar 22, 2009

junmag
  • 175 Answers

SOURCE: Rear brakes wont bleed. Sucks fluid in when brakes applied. Has ABS.

try this. open the two bleeder screw at the rear calipers. leave it open untill the fluid drips generously. close the bleeder. try the brakes. if it works bleed it the nornal way. note: make sure you dont run out of fluid in the master cylinder

Posted on Jun 02, 2009

  • 123 Answers

SOURCE: Slight air hiss or sucking sound near brake pedal and no

It maybe, I don`t know the vehicle personally but on Trucks and Buses, when this occurs, it usually points to the master cylinder piston seals which moves in and out as the foot pedal is operated. Does the hiss alter as the pedal is pushed down?? Does the hiss reduce or increase as the pedal is pushed down?? If it does, I think you`ll find that it`s this air seal between the piston and cylinder that`s failing and not the servo. Whether you car works the same way, I don`t know but I presume it must. Ian

Posted on Aug 06, 2009

moparhart
  • 245 Answers

SOURCE: 1999 Dodge Ram 1500 4X4. Abs & Brake light on

Sounds lie we have a brake line or brake hose problom.
have one person step on the brake the other look underneith and see where it is leaking, describe to me where is iss ill help ya get it fixed

Posted on Jul 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can you brake booster make you engine smoke


Sounds like some brake fluid has leaked down on your exhaust manifold and is smoking.

Apr 29, 2014 | 2002 Toyota Tundra

1 Answer

Why do brakes go to floor but still have light pressure?


It sounds like you have air in your brake lines. This is usually caused by a very low brake fluid in the master cyclinder.
To fix this problem fill up the master cyclinder with brake fluid and bleed the front wheel brake cyclinders until the air bubbles are removed. Keep the master cyclinder topped up with brake fluid. Then bleed the rear wheel brake cyclinders until the air bubbles are removed. Don't forget to top up the brake fluid in the master cyclinder.

Dec 31, 2011 | 2004 Chevrolet Cavalier

1 Answer

I replaced both front brake calipers in front on 95 concord and there is no brakes now like maybe air is in the system three calipers bleed having problems with front passengers bleeding ?


Try pumping the brakes and bleeding it at the master cyclinder. The air bubbles will eventually work its way up to the master cyclinder, BUT also make sure you keep the master cyclinder toped up on fluid.

Aug 16, 2011 | Chrysler Concorde Cars & Trucks

1 Answer

THE ABS LIGHT WILL COME ON AND THEN GO OFF AND WHEN YOU PUSH THE BRAKES IT MAKES A GUSHING SOUND.I HAVE CHANGED THE BEARINGS ON BOTH SIDES BUT THAT HAS NOT HELPED THE PROBLEM.


sounds like a brake master cyclinder issue ( bad O-rings ). or you have air in the system.
check the brake fluid reservoir and make sure that there is fluid in there,, if there is no fluid - then add fluid and now bleed all the air out of ALL the brake lines. if there is fluid in the reservoir then I would assume that the master cylinder is infact bad and needs to be replaced.

c...

Feb 06, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

Have a low sinking brake pedal after depressing 1 time? Changed out the master cyclinder?


Sounds like air in system. Bleed entire system starting at master cylinder, and check for any brake fluid leaks.

Oct 06, 2010 | 2002 Chrysler Town & Country

1 Answer

Brake line broke, replaced it, now I can't get fluid to the bleeders. I hear air but cannot get passed that. Now I have no brakes at all.!!


did you bleed the system good from air pockets...sometimes you have to remove the brake master cyclinder and bench bleed it to get all the air out...but your problem is to much air in system...start with bench bleeding the master cyclinder first.

Aug 15, 2010 | 1997 Nissan Pickup

1 Answer

Cruise control say not working and a symbol of the engine is on it changes gears and everythng fine


You probably have a vacuum leak. First: Check the brake vacuum line from the air intake manifold to the brake servo (black plastic pipe running from top of engine to brake servo with flange in the middle). It may be cracked. When engine at idle listen for leaks. You can run your hand along it to try to feel sucking.
Second:
If not that lift the black platic engine cover (3 screws) and look for cracks/leaks in the 1" black house running from front cyclinder bank to air intake manifold. It may be split/sucking air.

You may need to reset the Check engine light. Good luck

Jun 28, 2009 | 2002 Jaguar X-Type

3 Answers

No brakes after master cyclinder and booster replacment


To bleed the brake system open all the bleeders and let the system gravity bleed for @ 1/2 hour ensuring the master stays full. Then close all bleeders and starting furthest from the master (r/r) have someone pump the brakes 2-3 times,hold the pedal down, then open the bleeder,close the bleeder,and repeat untill there are no air bubbles and the brake fluid is running clear .Repeat for all wheels in this order R/R L/R R/F L/F ensuring master cykinder does not run empty. You cannot pump the pedal with a bleeder open you will be sucking air back into the system. Once you finish all wheels repeat to ensure there is no air remaining in system.

Apr 17, 2009 | Toyota Pickup Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...