Question about Cars & Trucks

1 Answer

How to fix wind up window on bmw 318i 1993

The wind up window comes off its rail and wont go up properly what is wrong with it?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 12,223 Answers

See the diagram attached. and fix it.
God bless ouhow to fix wind up window on bmw 318i 1993 - 3328125f-695a-4a05-adea-5664f94f57a1.jpg

Posted on Jul 25, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 16 Answers

SOURCE: replace ignition lock cylinder 1996 BMW 318i with 1995 BMW

no you can not

Posted on Mar 12, 2009

  • 1 Answer

SOURCE: BMW 318i wont start engine

check the starter

Posted on Apr 14, 2009

  • 44 Answers

SOURCE: The electronic windows in my 1993 BMW 318i do not work. Why?

Try checking the drivers master switch it may be bad and needs to be replaced...if it's bad none of the other door switches will work...the sunroof problem is most likely a fuse problem caused by your son when checking the fuses and either shorted one out or he wasn't looking when he was pulling it out and put it back into the wrong place next to where it's suppose to be.

Posted on Apr 19, 2009

  • 1810 Answers

SOURCE: BMW 320d E46 2001 rear right hand door window

if you go to the dealer they will copy the mech manule it you ask them as they want you to get frustrated and take it to them
so go on and ask and if all else fails take it to them or goto local parts store like auto zone they can preint it off too
dealer is best bet though

Posted on Aug 03, 2009

  • 15 Answers

SOURCE: Bmw 318i e46 overheating

sounds like a blown head gasket

Posted on Mar 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

VS COMMODORE My battery was accidentally connected wrong and now the car wont start ...


probably fried the ECM
substitute it with a known good one and go from there

Jul 03, 2016 | Cars & Trucks

1 Answer

Do i need to bleed the injector pump on my isuzu bighorn 4gj2 after replacing the head? as it wont fire


anytime you disconnect the fuel rail, and if it has a bleeder/test port (looks like a tire Valve), Then it needs to be bled before fuel will reach the injectors. Also check Spark plug ignition as well make sure grounds have been returned properly.

Oct 13, 2015 | Isuzu Cars & Trucks

1 Answer

How do I fix drivers window that wont go up or down on a 2000 dodge durango


This is a common problem in these model years of Chrysler vehicles, Be patient and you can easily DIY. The mechanism consists of a motor and two cable/two guide rail assembly. The guide rails hold the window onto the cable with a clip on each rail. It is better to buy the whole assembly new rather than just replacing a bad motor or just the guide rail/cable assembly. I have been burned just replacing one or the other only to learn when popping open the cable spool that 1) cable is shredded or 2) it ain't easy winding the cable back up as tight as the mfr had it and the window won't roll up with the same speed as the other one. You will need a Torx set... a 25 or 30 size if I remember will remove the guide rail bolts. Some models have the motors riveting on with soft aluminum rivets. Just drill them out... like butter. Others have torx bolts on them with the nuts encapsulated inside a grommet. Put your hand behind and inside the door panel to hold them with your hand when removing the torx bolts. Their are two holes on the inside of the door panel... one guide rail is extracted through one of them, and the other one through it's own hole. Push the window up first, have an assistance hold it halfway up for you so you can see and pull the guide rail release clips with needle-nose pliers. Push the window up all the way and tape it using a good tape around the door sill at the top. Then you can start removing/replacing the motor and guide rails. When your done, plug the wiring harness back in and raise the guide rail half way up using the motor and then unplug the harness again. Have your trusty assistant lower the window down gently, insuring it's inside the groove and stopped by the guide rail clip assembly. Insert the clips back in and test your work before re-assembling your door panel. Crutchfield makes new door panel liner, if yours is crispy. A heat gun sometimes help remove them more intact. Good luck!

Oct 05, 2014 | 2000 Dodge Durango

1 Answer

My 2002 Toyota camry drivers side window is off track when it's rolled up. Water leaks in and when your driving there is wind noise


You may have to review notes on how to remove the drivers side panel and replace one of the broken screws that hold the glass in place on the bottom rail. I believe the cause my be that and if not it may be a sticky guide rail. Try rubbing some furniture polish on the edge of the glass that sticks (usually to opposite side of the one that does not match the door). This may help to get the glass sliding smoothly again.

Mar 19, 2013 | 2002 Toyota Camry

1 Answer

My driver's window wont go up???!


one excellent tip for anyone with electric windows. always wind the window down to the last. the reason is if someone is leaning on the window talking to you it puts strain on the rails causing the window to go up crooked or even stick on the way up. also check the plug between the door and the car as if they come loose it wont work.

Sep 21, 2012 | 2003 Mitsubishi Eclipse Spyder

2 Answers

Main window switch on drivers side keeps going out-replaced three times-why


Most likely not the switch...
I had two impalas both have the rail rust out on the passenger side window. When the window rolls down, it falls out of the rusted out rail and ends up on the wrong side of the rubber guide. When you try to roll it back up, the window jams on the rubber and wont go back up.
In this case, it is not the switch, but rather the window guide rail.

Aug 27, 2012 | 2003 Chevrolet Impala

1 Answer

Sir i have a mercury sable 2003 and i have a problem that windo is not working


is it electric or manual wind up? if electric it may have come off its rail. or the motor in the window is stuffed which will mean replacing, if manual, have a look because it may have come off its rail also

Feb 26, 2011 | 2001 Mercury Sable

1 Answer

Hi I was wondering how to remove motor from front passenger side window will not operate up or down.


Take the inside door panel off.........This will give u access to the window moter...........U may have to change the power window rails as well but if not and just the moter.........make sure to be properly in time with the windings of the cable or damage to the cable may occure......Hope this helps.

Sep 13, 2010 | 2000 Ford Focus

2 Answers

03 Freelander sunroof wont close. One side looks like it is open tand the other side with the moving parts look closed. how do I fix this? Is there a way to take out the window?


Had a smiilar problem with my 2000 Freelander, the runners on the sunroof have plastice teeth which snap off, if you remove the plastic strips on the inside of the sunroof you can unscrew the glass take it out force the sunroof into the closed position and reattahch the sunroof, then never use it again

Jul 10, 2009 | 2003 Land Rover Freelander

1 Answer

Dodgy Windows


sounds like the windows have come off hteir tracks or possibly ave come out of allignment too many hard door slams please remove inner door skin with clip tool acess window frame area and inspect window going up and down with door skin removed you will see area where window is jamming and loosen nuts on window regulator and realign tighten bolts and test if not smooth loosen nuts again and realign good luck with project

Jun 30, 2008 | 1994 Hyundai Excel

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...