Question about Cars & Trucks

Open Question

SUBARU FORESTER EJ25 HEAD BOLT TORQUE SETTINGS

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: head bolts torque settings

According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Posted on Feb 07, 2009

Ad
  • 1779 Answers

SOURCE: head bolt toqure

Hope this helps, from autozone site. Curt
Application:
Cylinder head bolt torque sequence

Note :
Torque sequence:
---------
front | 3 1 6 |
of | |
vehicle | 5 2 4 |
---------
Step 1: Lightly oil cylinder bolt threads & washers
Step 2: Torque to 22 Ft/Lbs
Step 3: Torque to 51 Ft/Lbs
Step 4: Loosen all bolts 180 degrees
Step 5: Loosen all bolts 180 degrees
Step 6: Torque bolts 1 & 2 to 25 Ft/Lbs
Step 7: Torque bolts 3, 4, 5, 6 to 11 Ft/Lbs
Step 8: Turn all bolts an additional 80 to 90 degrees
Step 9: Turn all bolts an additional 80 to 90 degrees
*** CAUTION ***
engine uses Torque To Yield head bolts (TTY) that
permanently stretch during the initial installation.
New head bolts must be used when cylinder head is
replaced or re-installed to obtain proper Torque.

Posted on Apr 24, 2009

  • 370 Answers

SOURCE: 2004 Subaru Forester: Can you safely install spark

04 probly aluminum but i change spark plugs all day at work and just make sure there tight you dont need a torque wrench to put them in just sinch them down you will be fine.
good luck

Posted on Aug 24, 2009

MrSocket
  • 117 Answers

SOURCE: tighteneing torques settings for a subaru ej25

Your public library will have a manual covering your mechanical repair. Moreover, they have the automotive shops online software called AllData. It is the best auto technician database available today. You can print out specific troubleshooting procedures, diagrams, step-by-step istructions, and soforth. The typical person cannot afford to pay for this service, just automotive dealerships, etc... that is why the public library made it available to everyone and for free to view and print out material. This should Fixya! Good Luck!

Posted on Aug 28, 2009

alicantecoli
  • 22265 Answers

SOURCE: what are the cylinder head bolt torque wrench

allky head and block?? between 70/80 lbs

Posted on Nov 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I retorque the head bolts on my subaru forester 2003, I've just recently replaced the head gaskets?


Gaylene Green,


If you already had a heating issue... just skip over all this meaningless RE-Torque "STUFF"

If there was no overheating
before this procedure... I would suggest either the WRONG GASKETS were used... or they were somehow reversed blocking a water passage).

TORQUE has two ways to go...
Too loose = leaks (water and/or combustion)
Too TIGHT = Broken bolt/stripped threads

If it will make you happy

Sure... TIGHTEN... and then RE-TIGHTEN... after running.

That USED to be the way it was done... until they came out with WONDERFUL "Modern" head gaskets... (tighter... never looser... and NEVER (MORE) too tight.

If you think your torque is too much... you MUST also follow the REVERSE torque pattern when loosening (else risk a fractured casting (FOR REALS)).

Although I seriously doubt the desired effect...

The answer is SURE...!! Go for it... Re-Torque...

(Could not possibly hurt... unless you do it wrong!)

Just not sure of the "OVERHEAT" diagnosis...
sounds more than a bit odd.


***
If there is any previous history of overheating... I would pursue that as an INDEPENDANT issue.

Thermostat, defective water pump... radiator cap... or crusted up radiator (any or all of the above + rotten casting plugs in the engine).

Head torque... Naaah.

Mar 01, 2016 | 2003 Subaru Forester

1 Answer

2009 Subaru 2.5L Bolt Torque Specs


Pick up a repair manual. It will have the 30 or 40 different torque specs in it. IE head, intake, exhoust, rocker shaft, timing gears, etc, etc, etc.

Sep 04, 2014 | 2009 Subaru Forester 2.5

1 Answer

Need torque settings forester 1998


Wow what a imagination,bussiness slow? I am slow, no action today.

Mar 11, 2012 | 1998 Subaru Forester

1 Answer

Subaru ea71 flywheel bolt torque


torque is 72 N·m (7.3 kgf-m, 52.8 ft-lb)

Nov 20, 2009 | 1998 Subaru Forester

1 Answer

What are the clyinder head bolts torque wrench settings for a 1994 subaru impreza wrx


Impreza torque settings MUST be done in the correct sequence,its critical when re building.
If you have a local garage who are friendly with, ask if they have autodata.If so they can print you a torque sequence and settings.

Nov 10, 2009 | 1996 Subaru Impreza

1 Answer

Tighteneing torques settings for a subaru ej25 block ej20 cylinder head


Your public library will have a manual covering your mechanical repair. Moreover, they have the automotive shops online software called AllData. It is the best auto technician database available today. You can print out specific troubleshooting procedures, diagrams, step-by-step istructions, and soforth. The typical person cannot afford to pay for this service, just automotive dealerships, etc... that is why the public library made it available to everyone and for free to view and print out material. This should Fixya! Good Luck!

Aug 27, 2009 | 2002 Subaru Impreza

1 Answer

2004 Subaru Forester: Can you safely install spark plugs without a torque wrench....just by using the "hand Tighten" directions on the package (1/2 to 2/3 turn)?.....Is the forester an iron or aluminum...


04 probly aluminum but i change spark plugs all day at work and just make sure there tight you dont need a torque wrench to put them in just sinch them down you will be fine.
good luck

Aug 24, 2009 | 2004 Subaru Forester

1 Answer

98 subaru forester


Using a small 1/4" socket set and just your thumb and one finger with no leverage on the handle to tighten bolts. (kinda like chocking up on a bat if you know what I mean.) Starting in the middle go from one side to the opposite working your way to the corners. Use some "Permatex #2" to hold gasket in place and to help seal. Make sure not to over tighten bolts...it can actually cause it to leak.

Jul 26, 2009 | 1998 Subaru Forester

1 Answer

Head bolt toqure


Hope this helps, from autozone site. Curt
Application:
Cylinder head bolt torque sequence

Note :
Torque sequence:
---------
front | 3 1 6 |
of | |
vehicle | 5 2 4 |
---------
Step 1: Lightly oil cylinder bolt threads & washers
Step 2: Torque to 22 Ft/Lbs
Step 3: Torque to 51 Ft/Lbs
Step 4: Loosen all bolts 180 degrees
Step 5: Loosen all bolts 180 degrees
Step 6: Torque bolts 1 & 2 to 25 Ft/Lbs
Step 7: Torque bolts 3, 4, 5, 6 to 11 Ft/Lbs
Step 8: Turn all bolts an additional 80 to 90 degrees
Step 9: Turn all bolts an additional 80 to 90 degrees
*** CAUTION ***
engine uses Torque To Yield head bolts (TTY) that
permanently stretch during the initial installation.
New head bolts must be used when cylinder head is
replaced or re-installed to obtain proper Torque.

Apr 24, 2009 | 1995 Subaru Legacy

1 Answer

What are the torque settings for the cylinder head 2000 subaru forester


This procedure is for the SOHC only.

E: INSTALLATION
1. CYLINDER HEAD

  1. Install cylinder head and gaskets on cylinder block. CAUTION: Use new cylinder head gaskets.
  2. Tighten cylinder head bolts.
  1. Apply a coat of engine oil to washers and bolt threads.
  2. Tighten all bolts to 29 Nm (3.0 kg-m, 22 ft. lbs.) in alphabetical sequence. Then tighten all bolts to 69 Nm (7.0 kg-m, 51 ft. lbs.) in alphabetical sequence.
  3. Back off all bolts by 180° first; back them off by 180° again.
  4. Tighten bolts (a) and (b) to 34 Nm (3.5 kg-m, 25 ft. lbs.) .
  5. Tighten bolts (c), (d), (e) and (f) to 15 Nm (1.5 kg-m, 11 ft. lbs.) .
  6. Tighten all bolts by 80 to 90° in alphabetical sequence. CAUTION: Do not tighten bolts more than 90°.



  1. Further tighten all bolts by 80 to 90° in alphabetical sequence shown in figure provided. CAUTION: Ensure that the total "re-tightening angle" [in the former two steps], do not exceed 180°.

May 24, 2008 | 2000 Subaru Forester

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...