Question about Cars & Trucks

Open Question

2002 honda odyssey front slug stud - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: rear air conditioner

Hi Moonaw,
Take the vehicle to an expert on AC and ask them to check the gas pressure. If that's ok, then have the evaporator (that's the thing that looks like a small radiator which is the heat exchange unit inside the cabin. also have them check the expansion valve for the rear compartment...The fault must be in that section as the condenser, dryer and compressor are common to both front and rear outputs.

Best regards

Johngee10

Posted on Aug 27, 2008

  • 496 Answers

SOURCE: 2002 honda odyssey

Normal maintenance schedule at 75,000 miles:
Replace transmission fluid.
replace engine oil.
Rotate tires.
replace engine oil filter.
inspect brakes.
check parking brake adjustment.
inspect tie rod ends, steering gearbox and boots.
inspect suspension components.
inspect driveshaft boots.
inspect brake hoses and lines.
check all fluid levels.
inspect cooling system hoses.
inspect exhaust system.
inspect fuel lines and connections.

(At 90,000 do all of above plus:
replace air cleaner element.
inspect and adjust drive belts.
replace cabin air filter.)

Posted on Mar 28, 2009

ghost4548
  • 776 Answers

SOURCE: Front wheel stud broke off

Knuckle needs to be removed and the center hub 'pressed out' using a hydraulic press (accepted procedure). You can avoid this by using an air hammer and disk cutting tool to remove the old stud, then trim the 'stop flange' on the new stud (1/4 moon cut) in order to install it.... however, you gotta know what you're doing so you don't compromise the integrity of the new stud.

Posted on Jul 04, 2009

  • 3 Answers

SOURCE: 2002 Honda Odyssey will not start. Everything is

We've had our 02 Odussey do this a few times in the 8 years we've owned it, each time one or more interior lights were left on, usually one of the rear passenger map lights. Simple jump start and a few miles of driving to get it charged back up and all is fine. (IHMO battery capacity isn't sufficcent for all the accessories.)

Posted on Feb 13, 2010

swolfinor
  • 504 Answers

SOURCE: how to program garage door opener in 2002 honda odyssey

GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Posted on May 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What issues should I be looking forn with this vehicle


Check out these sites:

http://www.edmunds.com/honda/odyssey/2002/consumer-reviews.html

http://autos.msn.com/research/vip/Reliability.aspx?year=2002&make=Honda&model=Odyssey

http://www.carcomplaints.com/Honda/Odyssey/2002/

Jan 13, 2013 | 2002 Honda Odyssey

1 Answer

Wheel stud removal honda odyssey


I am currently doing the front driver side. If you have the big center nut without a cotter pin, I would suggest you have a shop do it. There is no way to remove and install lug bolts on this particular vehicle without removing the hub, and this hub SUCKS to remove. Here is what I did, and NO, I do not recommend doing it this way. Remove wheel and brake caliper assy. Suspend brake to keep weight off the brake line. Remove two philips head screws holding rotor to hub. These screws can be frozer tight. I used an impact type screwdriver to remove these. Remove the large nut..lmao...sounds easy. This nut is 36mm but i got away with using a 1-7/16 6 sided impact socket with a 1inch impact wrench. A huge breaker bar would work as well. I imagine the foot pounds to be astronomical and I doubt most saturday mechs will have the tools to remove it. Put the rotor back on, but backwards. Use a couple of lug nuts to bolt it to the hub. There is enough left of the broken lugs to use them. I then took a typical harmonic balance removal tool and utilized the two holes that had the philips head screws. Using the spindle as my center, I applied pressure to the spindle, causing it to retreat back into the hole. When the pressure got decent, I took two small pry type tools and put them between the back of the hub and fixed piece, probably called a steering knuckle or something. Kept wiggling and prying little by little...added a little more balancer pressure...more prying...it works it way out..finally. I believe the manual says to use a large slide hammer system to remove the hub. Wish I had one. Hammer out the old studs, press in the new. You can also using open lug nuts to pull the studs flush. Just make sure the splines are lined up. Assy is much much easier.

Jan 08, 2012 | 2002 Honda Odyssey

1 Answer

How to remove tail light assembly of 2002 Honda odessey


After removing the two screws, stand by the side of the odyssey with your back to the front of the vehicle, gently push at the light assembly with a screw driver (flat) towards the back of the vehicle. I hope this helps!

Sep 23, 2011 | 2002 Honda Odyssey

1 Answer

2002 Honda Odyssey. Hood won't open when latch is pulled. How else can I open hood?


if you can get hold of the outer cable at front of hood and pull it hood might pop

Sep 19, 2011 | 2002 Honda Odyssey

1 Answer

2002 Honda Odyssey van, the windshield washer doesn't squirt fluid or wipe the wipers, though the windshield wipers work separately . . . . how to fix?


Sounds like you may need to change the washer fluid pump. They do go bad. It's located inside the washer fluid reservoir, which is in the front of the passenger's side wheel well, behind the front bumper.

Mar 31, 2011 | 2002 Honda Odyssey

1 Answer

How to remove a front wheel stud on a 2003 honda odyssey


If you hit it with a hammer straight on, it will pop out the back of the hub. Make sure it's rotated to a point where it will not catch on anything like a brake part or pipe.

Aug 16, 2009 | 2003 Honda Odyssey

1 Answer

Front fan only works in high, A/C does not work


Maybe a ground has been interrupted somewhere?? Take it back to where they serviced it.

Jun 04, 2009 | 2002 Honda Odyssey

1 Answer

Firing order on my Honda Odyssey 2002.


the firing order on the 3.5 engine is 1-4-2-5-3-6

3 4
2 4
1 4
>>>>>front of engine

May 07, 2009 | 2002 Honda Odyssey

1 Answer

2002 Honda Odyssey Problem


Sorry class07932,
Please explain in more detail what you mean?

Rgards Johngee10

Jul 18, 2008 | 2002 Honda Odyssey

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...