Question about Cars & Trucks

Open Question

Replace front drag link end on ldv pilot city van

Where and how do I replace it

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 18 Answers

SOURCE: Noise in front when i hit bumps

A drag link is one of the many components of your steering assembly what type if noise are you hearing, is your steering tight or loose?

Posted on Nov 19, 2008

Ad
  • 3 Answers

SOURCE: replace sway bar end links '97 GMC Sierra

if you put your vehicle information in at advanceautoparts.comyou can search sway bar and find parts that you need - there was someinfo missing on which sierra model you have as far as engine size andvin # match but I came to: http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/partlist_Sway-Bar-Link-Kit_78_R|GRPCHASAMS__sway%20bar___

Posted on Sep 17, 2009

SOURCE: 99 Discovery 2 I have replaced the shocks, steering drag link and

The ball joints probably have gone,what you have to do ,lift the front of the vehicle,like you are taking out the front wheel ,after having lifted the vehicle by a jack,now the wheel with your two hands,then do different movement with the wheel,if the ball joint has gone you will sure hear a noise and see a free play to the wheel.Do this action for the two front wheels.

Posted on Jan 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix 5th gear on my ldv maxus


Its likely you have a problem with the clutchnot completly disengageing or problems with disk or pressure plate

Jun 13, 2013 | 1997 Chevrolet Cargo Van

2 Answers

Help!!! how to reset a LDV Maxus key fob?


Hi
I know from experience that you cannot really re synch these fobs on the LDV Maxus vans.
What actually is the fault is an onboard component on the pcb has failed and we normally just replace that with a new one..the fob will be tested for operation and sent back. OR its the Relay in the ESA unit - under the left hand front glovebox on the bulkhead - black with cables going into it. We have those relays (soldered to the pcb) we can supply those or do the work for you. The fob connects to that ESA and the unit then fires the relays to open/close the doors. Sometimes that unit is installed upside down which causes water (condensation) to enter the box and have fun with your electrics.
The fob is SYNCHED to this unit via coding we can use your old fob to clone to a new fob and that will work with the ESA and the vehicle.
We have the parts on this link Items for sale from remobilise ltd

Here is a link to how to program the fob to the vehicle via the programmer - NOTE how you MUST have a working fob to program another (text at the start of the video... LDV Maxus flv

We can fix most problems on the LDV Maxus that occur with faults to do with the Central locking/fobs/ESA/ETACS - three relays are in the ESA and they control ONLY the central locking - two more relays are in the ETACS unit (behind the ashtray) and they control the fogs and intermittant wipers.

Any help or info needed please contact info@remobilise.co.uk
or tel 01792 896404.

We are based in Swansea UK.

Aug 30, 2012 | Cars & Trucks

1 Answer

Ldv pilot alternator pully diagram


HI WHAT DOES A ALTRENATOR LOOK LIKE IN A 02 LDV PILOT PLEASE

Jul 02, 2012 | Cars & Trucks

1 Answer

STeering wheel is loose and noisy while steering. Sounds like something broke inside.


This might help to understand the steering linkage: REMOVAL & INSTALLATION Fig. 1: Steering linkage used on the Bronco and 4-wheel drive F-150 84928067.gif
Fig. 2: Steering linkage used on the 4-wheel drive F-350 84928070.gif
Fig. 3: Steering linkage used on F-Super Duty chassis/cab 84928071.gif
Pitman Arm EXCEPT F-SUPER DUTY STRIPPED CHASSIS AND MOTOR HOME CHASSIS
  1. Place the wheels in a straight-ahead position.
  2. Disconnect the drag link at the Pitman arm. You'll need a puller such as a tie rod end remover.
  3. Remove the Pitman arm-to-gear nut and washer.
  4. Matchmark the Pitman arm and gear housing for installation purposes.
  5. Using a 2-jawed puller, remove the Pitman arm from the gear.
  6. Installation is the reverse of removal. Align the matchmarks when installing the Pitman arm. Tighten the Pitman arm nut to 170-230 ft. lbs. (230-312 Nm); torque the drag link ball stud nut to 50-75 ft. lbs. (68-102 Nm), advancing the nut to align the cotter pin hole. Never back off the nut to align the hole.
F-SUPER DUTY STRIPPED CHASSIS MOTOR HOME CHASSIS
  1. Matchmark the Pitman arm and sector shaft.
  2. Disconnect the drag link from the Pitman arm.
  3. Remove the bolt and nut securing the Pitman arm to the sector shaft.
  4. Using a 2-jawed gear puller, remove the Pitman arm from the sector shaft. To install:
  5. Aligning the matchmarks, slide the Pitman arm onto the sector shaft. If the arm won't slide on easily, use a cold chisel to spread the separation. NEVER HAMMER THE ARM ONTO THE SHAFT! Hammering on the arm will damage the steering gear!
  6. Install the nut and bolt. Tighten the nut to 220-300 ft. lbs. (298-407 Nm).
  7. Connect the drag link.
Tie Rod and Drag Link EXCEPT RUBBERIZED BALL SOCKET LINKAGE
  1. Place the wheels in a straight-ahead position.
  2. Remove the cotter pins and rust from the drag link and tie rod ball studs.
  3. Remove the drag link ball studs from the right-hand spindle and Pitman arm.
  4. Remove the tie rod ball studs from the left-hand spindle and drag link.
  5. Installation is the reverse of removal. Seat the studs in the tapered hole before tightening the nuts. This will avoid wrap-up of the rubber grommets during tightening of the nuts. Tighten the nuts to 70 ft. lbs. (95 Nm). Always use new cotter pins.
  6. Have the front end alignment checked.
RUBBERIZED BALL SOCKET LINKAGE
  1. Raise and support the front end on jackstands.
  2. Place the wheels in the straight-ahead position.
  3. Remove the nuts connecting the drag link ball studs to the connecting rod and Pitman arm.
  4. Disconnect the drag link using a tie rod end remover.
  5. Loosen the bolts on the adjuster clamp. Count the number of turns it take to remove the drag link from the adjuster. To install:
  6. Installation is the reverse of the removal procedure. Install the drag link with the same number of turns it took to remove it. Make certain that the wheels remain in the straight-ahead position during installation. Seat the studs in the tapered hole before tightening the nuts. This will avoid wrap-up of the rubber grommets during tightening of the nuts. Tighten the adjuster clamp nuts to 40 ft. lbs. (54 Nm). Tighten the ball stud nuts to 75 ft. lbs. (102 Nm).
  7. Have the front end alignment checked.
Connecting Rod RUBBERIZED BALL SOCKET LINKAGE
  1. Raise and support the front end on jackstands.
  2. Place the wheels in the straight-ahead position.
  3. Disconnect the connecting rod from the drag link by removing the nut and separating the two with a tie rod end remover.
  4. Loosen the bolts on the adjusting sleeve clamps. Count the number of turns it takes to remove the connecting rod from the connecting rod from the adjuster sleeve and remove the rod.
  5. Installation is the reverse of removal. Install the connecting rod the exact number of turns noted during removal. Tighten the tie rod nuts to 40 ft. lbs. (54 Nm); the ball stud nut to 75 ft. lbs. (102 Nm).
  6. Have the front end alignment checked.
Tie Rod Ends RUBBERIZED BALL SOCKET LINKAGE Fig. 4: Remove the cotter pin from the castellated nut at the ball stud 88288p02.jpg
Fig. 5: Remove the nut from the ball stud 88288p03.jpg
Fig. 6: Use a tie rod end puller tool to remove the ball stud from the Pitman arm 88288p04.jpg
Fig. 7: Liquid correction fluid makes excellent paint to mark the threads of the tie rod end 88288p05.jpg
Fig. 8: For a more accurate reinstallation, you may measure the tie rod end prior to removal 88288p06.jpg
Fig. 9: After having loosened the nut, unscrew and remove the tie rod end 88288p07.jpg
  1. Raise and support the front end on jackstands.
  2. Place the wheels in a straight-ahead position.
  3. Remove the ball stud from the Pitman arm using a tie rod end remover. NOTE: Optional: paint a mark or measure the length of the tie rod end threads to ease reinstallation in as close to the original position as possible.
  4. Loosen the nuts on the adjusting sleeve clamp. Remove the ball stud from the adjuster, or the adjuster from the tie rod. Count the number of turns it takes to remove the sleeve from the tie rod or ball stud from the sleeve. To install:
  5. Install the sleeve on the tie rod, or the ball in the sleeve the same number of turns noted during removal. Make sure that the adjuster clamps are in the correct position, illustrated, and torque the clamp bolts to 40 ft. lbs. (54 Nm).
  6. Keep the wheels facing straight-ahead and install the ball studs. Tighten the nuts to 75 ft. lbs. (102 Nm). Use new cotter pins.
  7. Install the drag link and connecting rod.
  8. Have the front end alignment checked.
prev.gif next.gif

Sep 18, 2010 | 1996 Ford F150 Regular Cab

1 Answer

2001 Toyota Sienna XLE mini Van Soft steering problem


you may have worn front end parts , have frt end checked you dont want to loose your steering good luck.

Oct 20, 2009 | 2002 Toyota Sienna

1 Answer

Heater blowing luke warm when on hot on a ldv pilot


you should eather replace your heater core or upgrade your thormastat to a higher temp. one

Dec 04, 2008 | Fiat 124 Cars & Trucks

6 Answers

2002 chrysler mini van front end noisy .when you hit a bump.what


I had the same problem with my 2002 Town and Country Limited. I took it to the mechanic and had the sway bar links and ball joints replaced and still had the same clunking noise when going over bumps at low speeds. The van sounded great on the highway, but country roads were horrible. I was about to replace the struts and pay another 700 dollars when i read somewhere that the sway bar bushings could wear and cause the noise. I took it to the mechanic and he said absolutely not it would be a waste of money. Being the stubborn guy I am, I went to NAPA and bought the two bushings for 12 dollars and replaced them myself in an hour. I took the van for a test ride and the noise is completely gone. Please ignore your mechanic and replace the bushings ASAP! Pretty cheap try even if it doesn't work.

Nov 14, 2008 | 2002 Chrysler Town & Country

1 Answer

How long should new LDV's convoy backwheel brake drums serve?


if you pay for cheap parts,that will happen,buy the best parts for brakes

Apr 18, 2017 | 1989 Audi 200

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...