Question about Cars & Trucks

Open Question

1997 Honda CRV camshaft position sensor location

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

blueextc3221
  • 15935 Answers

SOURCE: camshaft position sensor location

crank sensor is a component used in an internal combustion engine to monitor the position or rotational speed of the crankshaft. This information is used by engine management systems to control ignition system timing and other engine parameters. Before electronic crank sensors were available, the distributor would have to be manually adjusted to a timing mark on the engine.

The crank sensor can be used in combination with a similar camshaft position sensor to monitor the relationship between the pistons and valves in the engine, which is particularly important in engines with variable valve timing. It is also commonly the primary source for the measurement of engine speed in revolutions per minute.

Crank sensors in engines are usually comprised of magnets and an inductive coil. They are principally based on the Hall effect. Common mounting locations include the main crank pulley, the flywheel, or occasionally on the crankshaft itself.

Some engines, such as GM's Premium V family utilise crank position sensors which read a reluctor ring integral to the Harmonic Balancer. This is a much more accurate method of determining the position of the crankshaft, and allows the computer to determine within a few degrees the exact position of the crankshaft (and thereby all connected components) at any given time.

Posted on Dec 27, 2008

  • 218 Answers

SOURCE: Camshaft Position Sensor Location

IF U GO TO THE RIGHT SIDE OF THE ENGINE AND LOOK 4 INCHES BEHIND THE BELT IT WILL BE ON TOP OF THE TIMING COVER.THE WIRES WILL BE RED/WHITE,BLACK,BROWN/WHITE

Posted on May 05, 2009

  • 144 Answers

SOURCE: Where is the camshaft position sensor located in a 2001 VW Passat

when you are looking at the engine pull off the plastic cover on top then the front cover that covers you timing belt there is a wire harness tha goes right to it in the left upper coner two ten mil bolts and it comes off careful not to drop bolts down in belt that could be bad. it is that easy

Posted on Sep 01, 2009

  • 14036 Answers

SOURCE: 98 silverado 5.7L camshaft position sensor

ITS ABOVE CRANKSHAFT PULLEY.IT CONNECTS WITH CRANKSHAFT POSITION SENSOR.

Posted on Oct 23, 2009

emissionwiz
  • 75197 Answers

SOURCE: where is the camshaft position

if u look on the drivers side of the top of the engine the cam sensor is in the block where the distrutor used to go, here is a picture of it4fd7155.jpg

Posted on Sep 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The location of the camshaft censor on a HONDA C.R.V 1999


There is no dedicated cam sensor on these devices. The cam position is sensed by the electronics in the distributor.

Feb 02, 2016 | 1999 Honda CR-V

1 Answer

Where is the camshaft sensor located on a 2005 honda crv


on end of the cam.
no engine stated of the many options, so ......?????
nor why you ask.
DTCs?
what?
login to
alldata.com and read. its all there.

Feb 14, 2014 | 2005 Honda CR-V

1 Answer

Where is the camshaft sensor located on a 1997 Ford T Bird LX 4.6


The camshaft position sensor is on the left (drivers) side on the front cover

Aug 22, 2012 | Cars & Trucks

3 Answers

Honda 97 crv engine turns off while driving, and hard to


, pull a plug wire and ground it to the engine body and check for spark. if spark then
check your fuel system pressure, fuel pump

Aug 28, 2009 | 1997 Honda CR-V

1 Answer

Central locking unit 1997 Honda CRV


Hi the central lock unit is located in the drivers door

Mar 16, 2009 | 1997 Honda CR-V

1 Answer

1997 mercury sable camshaft sensor replacement


do you have 3.L 2v or 4 valve?

3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder blocks (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (12270) (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder blocks.
Installation
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be used to position the synchronizer assembly prior to installation of the camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs. Locate camshaft position sensor electrical connector in the pre-removal position.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (14-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.

Feb 22, 2009 | 1997 Mercury Sable

2 Answers

Camshaft sensor


It is located at the right rear of the engine block. It has a plug with three wires in it. Hope this helps.

Oct 21, 2008 | 1997 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...