Question about Cars & Trucks

Open Question

2007 ford escape p0733 & p0734 - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
wracefans24
  • 1985 Answers

SOURCE: 2001 Jeep Grand Cherokee won't shift out of first

P0733=Gear 3 Incorrect Ratio
P0734=Gear 4 Incorrect Ratio,
your transmission is in "limp" mode,
Have the following sensors checked on the transmission,input sensor,output sensor,and speed sensor.
The transmission is not getting a signal from one of them,So it doesn't know how fast your going so it doesn't up shift.

Posted on Jan 22, 2010

Ad
  • 181 Answers

SOURCE: 2002 dodge dakota code p0733 p0734

This code means gear ratio dont match from in to out on transmission in 3rd po733 4th po734 first thing to do is do a filter change and replace the fluid.LOOK for metal shavings. If you see alot could be interal problems. I have seen this fixed by a good trans flush Hope this helps

Posted on Feb 17, 2010

  • 1 Answer

SOURCE: trans in limp mode with codes P0700, P0733 and P0734

1998 dodge caravan code P0700-Transmission Control System (Malfunction Indicator Lamp Request) How do I fix this?

Posted on Nov 17, 2010

partyd
  • 141 Answers

SOURCE: My van is not shifting

734 is "Gear 4 Ratio Incorrect

the acumulator inside the tranny is bad

Posted on Nov 23, 2010

  • 16 Answers

SOURCE: p0700 p0733 p0734 1997 chrysler intrepid

P0700 codes are Transmission DTC's (Diagnostic Trouble Codes)...

The specific codes are Incorrect Gear Ratio codes. This problem could be caused by low transmission fluid, deteriorated transmission fluid, a shift solenoid malfunction, the transmissions line pressure, quite a few electrical problems, etc. First step would be to check the fluid level the correct way. The vehicle must be up to operating temperature, and the shifter must be in the Neutral position. Also look at the color of the fluid. If the fluid is no longer the right condition, (most of the time it is bright red) it will be brown, or darker looking. Also smell the fluid, it may smell burnt. If this is the case, the clutch may also be slipping. In conclusion, if the fluid is NOT the problem, you may need to have the transmission tested by a certified technician. Hope this helps you.

Posted on Feb 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my Hyundai accent 05 codes are p0732,p0733, p0734 how do infix it?


Not sure but by the looks of the numbers and the fact they are sequential my guess would be a misfire in cylinders 2,3, & 4.

Aug 24, 2014 | Cars & Trucks

1 Answer

No tenago dinero y mi carro hyundai 2004 me esta dando problemas no coje la riversa y cambia de cantaso y le pusieren la maquina y me *** estos codigos p2o96,p0734,p0733,p1709,p2096


P0733 - Gear 3 Incorrect ratio
P0734 - Gear 4 Incorrect ratio
P1709 - Park or Neutral Position Switch out of Self-Test Range
Check out this TSB 03-40-016

Some 2000-2002 ACCENT vehicles may experience the following conditions: Diagnostic Trouble Code (DTC) P0722: No pulse generator-B signal Third-gear "Fail-Safe" condition
"Check Engine" light on

If the vehicle experiences the above symptoms: Inspect the pulse generator-B and replace if necessary.
Reprogram the TCM using the Hi-Scan Pro

VEHICLES AFFECTED: Model: 2000-2002 Accent vehicles with automatic transmissions
Affected vehicle production date range:
3 DR: Produced through October 11, 2002
4 DR: Produced through September 3, 2002

Affected vehicle identification number (VIN) range:
3 DR: Produced through KMHCF35C63U235415
4 DR: Produced through KMHCG45C03U412818

The problem is you will have to take it to the dealer to get the reprogram done.


P2096 - Fuel trim too lean. Usually means vacuum leak. Look for crushed, broken or melted off vacuum hoses near intake manifold. Or an obvious hissing noise at a normal idle. If so replace or repair clear codes your done. If not obvious take carb cleaner spray with nozzle attached car running & go over all vacuum hoses, intake manifold, EGR valve see if idle raises if so you found leak. Repair. Could also be bad oxygen sensor switching bad O2 sensor but rarely.


Hope this helps!

Sep 21, 2010 | Hyundai Motor 2004 Accent

1 Answer

Transmission Problem - Ford Escape 2006


P0732 and P0734 indicates gear ratio errors in 2nd and 4th gears, basically no 2nd and 4th gear. The one thing 2nd and 4th gear has in common is the band, the band is known to break, this is a common failure with this transmission and happens on a regular basis.

You need to remove the transmission to repair it.

Jan 25, 2010 | 2006 Ford Escape

1 Answer

2001 Jeep Grand Cherokee won't shift out of first gear and the fault codes are P0733 and P0734.


P0733=Gear 3 Incorrect Ratio
P0734=Gear 4 Incorrect Ratio,
your transmission is in "limp" mode,
Have the following sensors checked on the transmission,input sensor,output sensor,and speed sensor.
The transmission is not getting a signal from one of them,So it doesn't know how fast your going so it doesn't up shift.

Jan 22, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Have a 2001 tiburon showing engine light went to auto zone had codes p1624 p0733 p0734 p1624 bblow cooling fan relay cicuit fault probable cause BB1open or short circuit condition BB2 poor electrical...


Take/Tow your vehicle to an authorized Hyundai dealership and pay the diagnostic fee... they will tell you exactly what the problem is and the cost of parts/labor to fix it... at least this way you'll know what the problem is and what's required to fix it.

Sep 26, 2009 | 2001 Hyundai Tiburon

1 Answer

Chrysler Neon auto gearbox problems


P0733 IS GEAR RATIO ERROR IN 3RD AND P0734 IS GEAR RATIO ERROR IN 4TH..THESE CODES USUALLY MEAN AN INTERNAL PROBLEM IN TRANSMISSION,BUT CHECK WIRES AT SPEED SENSOR CONNECTORS FOR BROKEN WIRES BY PULLING ON WIRES AND WIRING NEAR SOLENOID PACK FOR CHAFING..I HOPE THIS HELPS..YOU MIGHT WANT TO DROP THE TRANS PAN AND LOOK FOR A PLUGGED FILTER OR DEBRIS IN PAN..MAKE SURE THE TRANS COOLER IN RAD HAS NOT FAILED ALSO

Aug 14, 2009 | Chrysler Neon Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...