Question about Cars & Trucks

Open Question

Starter grinding on 2000 Chevrolet Express 5.7 liter van

Starter grinding bad, starter and flywheel have been replaced

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Bat1956
  • 585 Answers

SOURCE: 93 buick lesabre 3.8 liter starter replaced,new one just clicks

Given the steps you have taken, only one of two things this can be is a resistive connection between the battery and the starter solenoid terminal. Or the battery itself has a bad internal connection. Bear in mind: you cannot crank the engine through the average set of jumper cables unless the battery in the dead vehicle will hold and deliver a good charge. Jumper cables are not really intended to start the car, they are for boosting the good, but low battery in the car being jumped.

Posted on Dec 16, 2008

  • 1 Answer

SOURCE: location Fuel Tank Pressure Sensor on a 2005 chevy express van

lOOK UNDER THE REAR OF THE VEHICLE ABOVE THE SPARE TIRE ON A CROSSMEMBER BETWEEN THE FRAME RAILS.

Posted on Apr 24, 2009

  • 303 Answers

SOURCE: 2000 chevy express 1500 van having starting issues

Start with fuel system. Listen for fuel pump humm at fuel tank No humm check wiring to pump for power. Then check for spark at plugs and wires. Remove wire from coil and hold near engine and see arch when you crank. No arch. Replace ignition Modular inside distributor cap or cap or rotor

Posted on Feb 04, 2010

  • 14036 Answers

SOURCE: I need the serpentine belt diagram for a chevy Express Van

DRIVE BELT DECAL SHOULD BE UNDER THE HOOD.OR YOU CAN GO TO DEALERSHIP GET ONE AUTO ZONE OR ADVANCE AUTO PARTS CAN GET YOU ONE.OR YOU CAN BUY A HAYNES REPAIR MANUAL IT HAS BELT DIAGRAM.

Posted on Mar 10, 2010

  • 1 Answer

SOURCE: I need a diagram of fuse box for 2000 Chevy Express Van

i have a 2000 Chevy van where is the fuse for the two(2) rear power outlets

Posted on Apr 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring diagram chevy van


Fixed Problem (it was my van) no power to ignition wire at starter. Replaced Ignition lock cylinder. just worn down. (Delivery van 50-60 starts a day). 160k miles.

Apr 25, 2013 | 2000 Chevrolet Express Cargo

2 Answers

How do I stop the grinding when starting 2000 Astro Van


Hello Anonymous...

To inspect the teeth on the ring gear requires the inspection to check the full 360 degrees of the ring gear. Looking past the inspection cover to examine a small portion of the ring gear may reveal no issues, but only for that section. Eventually the ring gear will end up positioned above the starter drive gear which will skip across the bad teeth creating your grinding noise when you try and start the Astro,.

Apr 26, 2017 | 2000 Chevrolet Astro

1 Answer

2000 Chevy s10 manual changed starter still won't start the starter is spinning but the engine won't turn over.


Do you have the correct starter and is it grinding, this sounds like a bad flywheel or wrong starter or even a bad one. look at teeth of flywheel and see if they are damaged. good day

Jun 19, 2011 | 2000 Chevrolet S-10

3 Answers

I have a 1996 astro van...when i go to start and turn ignition it makes this real bad grinding sound? could it be the flywheel or the starter ?


It could be either the flywheel or the starter.
If it's grinding, don't try it again until you've removed and examined the starter and flywheel. If the starter solenoid isn't fully engaging the bendix, it will cause the gear to grind; replace or rebuild the starter if that's the case.
But you should examine the flywheel to see if it is seriously damaged from the problems you've had. Put a mark on the flywheel using a magic marker, then examine the flywheel as you slowly turn the engine by hand. (make certain that the ignition is off when you do that, you don't want anything bad to happen to your hand.) The mark on the flywheel will indicate when you've been able to examine the all of the teeth on the starter ring.

Mar 19, 2011 | 1996 Chevrolet Astro

2 Answers

Car grinds as soon I try to start the ignition.It takes several times to turn the turn the key to start the ignition with the grinding sound.The people at the autozone tested it and say,"the...


2 possible things, 1. the contacts in the solinoid on the starter are bad, it would still test good but wouldnt have enouph power to engage the flywheel, replace starter, or 2. bad flywheel, teeth on flywheel are worn or broken, both require removal of starter, remove starter first inspect flywheel for damage, if none replace starter.

Oct 26, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

97 i got 83 ford clubwagon,5.8,vin G,2bbl .smooth quite starts til 2000,started dragging,replaced it. grinds since then,5 starters..ruined 3 flywheels. auto zone. engine/trans always bolted tight.i gave...


Before spending any more money you need to check for excessive end play in the crankshaft and if that is the cause then the bearings need to be replaced.NOTE:Ford starters do NOT require shims,you want the gears to mesh deeply as possible,

Jul 28, 2010 | Ford Econoline Wagon Cars & Trucks

2 Answers

Grinding noise when ignition is turned


THe starter engages the fly wheel and in the process turns the motor over to cause it to crank. The grinding can be a bad starter causing the gear to either not engage fully or not disengage. It can also indicate missing teeth on the flywheel from damage from starter. If the car cranks and grinding goes away it points to the starter solenoid not engaging properly.. pushing gear into contact with flywheel. I would recommend replacing the starter and you can replace it with a good mechanical knowledge and DIY.

Jun 08, 2010 | 1997 Chevrolet Cavalier

1 Answer

Where is the starter located on my 2000 chevy


Under your van on the passenger side just above the oil pan on the side of the engine block, bolts into the transmission bell housing, hope this was very helpful.

May 11, 2010 | 2000 Chevrolet Express Cargo

3 Answers

When i try to start the car it makes a funny sound and wont start it sounds like something is not catching


Good indication of a bad starter. Is it just clicking or is it a grinding ugly noise?. The second is definately the starter.

Nov 01, 2009 | 1997 Chevrolet Cavalier

1 Answer

Grinding noise when trying to start, engine will not crank


Starter bendix is stuck and not engaging the flywheel. Or the starter gear is engaging the flywheel and the overrunning clutch in the starter is bad. Either way, you are looking at a starter replacement.

Jul 08, 2009 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...