Question about Cars & Trucks

Open Question

Head bolts torque settings for 2001 toyota rav4

Replacing head gasket need headbolt specs cam bolt specs timing chain specs

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75051 Answers

SOURCE: 2005 Tucson

camshaft sprocket bolt 58-72 ft. lbs. crankshaft pulley bolts 108-132 ft. lbs. crankshaft pulley center bolt 80-94 ft. lbs. cylinder head bolts cold engine 65-72 ft. lbs. warm engine 73-80 ft. lbs. cylinder head rear cover bolts 69-86 in. lbs. flywheel/Driveplate bolts 94-101 ft. lbs. intake/Exhaust manifold nuts/Bolts 11-14 ft. lbs. jet valves 13-16 ft. lbs. main bearing cap bolts 36-39 ft. lbs. oil pan bolts 51-69 in. lbs. oil pan nuts 43-60 in. lbs. oil pan drain plug 33 ft. lbs. oil pump cover bolts 72-84 in. lbs. oil pump relief valve plug 29-36 ft. lbs. oil pump sprocket nut 25-28 ft. lbs. Rear oil seal retainer bolts 84-108 in. lbs. rocker arm shaft bolts 14-15 ft. lbs. rod bearing cap nuts 23-25 ft. lbs. silent shaft sprocket nut 22-28 ft. lbs. spark plugs 15-21 ft. lbs. thermostat housing-to-Engine bolts 86-114 in. lbs. timing belt tensioner bolt 32-40 ft. lbs. valve cover bolts 43-61 in. lbs. water pump-to-Engine bolts alternator brace bolt 14-20 ft. lbs. all others 9-11 ft. lbs. water pump pulley bolts 72-84 in. lbs.

Posted on Sep 08, 2008

  • 512 Answers

SOURCE: Head Bolt Torque for a 2000 Grand Cherokee Laredo 4.0L

the torque is a 4 step process

1 torque all bolts to 22 ft/lbs
2 torque all bolts to 45 ft/lbs
3 recheck all bolts to 45 ft/lbs
4 torque bolts 1 thru 10 to 110 ft/lbs
bolt 11 to 100 ft/lbs
bolts 12 thru 14 to 110 ft/lbs
bolt #1 is the fourth bolt from the front on the passenger side....#2 is the fourth bolt on the drivers side then you continue in a clockwise order

Posted on Jan 04, 2009

SOURCE: need to know cylinder head bolt torque specs

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Posted on Feb 07, 2009

  • 701 Answers

SOURCE: torque specs for toyota tercel

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using6bd0ae1.jpg FixYa. Roger

Posted on Apr 15, 2009

wilsodfarm
  • 986 Answers

SOURCE: Torque Specs for Head Bolts on 1997 GMC Sierra V8 5.0 Vortec?

.0L Torque Specs Belhousing to engine bolts 28-38 ft/lbs Camshaft sprocket bolt 40-45 ft/lbs Camshaft thrust plate to engine block bolts 108-144 in/lbs Crankshaft pulley to vibration damper bolts 35-50 ft/lbs Cylinder head bolts -1979-1992 --Step 1 55-65 ft/lbs --Step 2 65-72 ft/lbs -1993-up --Step 1 25-35 ft/lbs --Step 2 45-55 ft/lbs --Step 3 75-85 ft/lbs Differential shaft lock bolt 15-30 ft/lbs Driveshaft U-joint to pinion flange bolts 70-95 ft/lbs Exhaust manifold bolts 26-32 ft/lbs Flywheel mounting bolts 75-85 ft/lbs Front engine mount nuts 72-98 ft/lbs Intake manifold to head bolts --Step 1 96 in/lbs --Step 2 16ft/lbs --Step 3 23-25 ft/lbs Intake manifold (upper intake to lower) 12-18 ft/lbs Oil filter insert to engine block adapter bolt 20-30 ft/lbs Oil pan mounting bolts -1979 --Step 1 (Large bolts) 11-13 ft/lbs --Step 1 (Short bolts) 7-9 ft/lbs --Step 2 (Large Bolts) 15-17 ft/lbs --Step 2 (Short Bolts) 10-12 ft/lbs -1980 to 1987 9-11 ft/lbs -1988 to 1993 6-9 ft/lbs -1994-up 110-144 in/lbs Oil pickup tube to main bearing cap nut 22-32 ft/lbs Oil pickup tube to oil pump bolts -1979 to 1987 10-15 ft/lbs -1988-up 12-18 ft/lbs Oil pump mounting bolts 22-32 ft/lbs Pinion bearing preload 8-14 in/lbs Pressure plate to flywheel bolts 12-24 ft/lbs Rocker arm fulcrm bolts 18-25 ft/lbs Spark plugs 7-14 ft/lbs Timing chain cover bolts 12-18 ft/lbs Vibration damper to crackshaft bolt 110-130 ft/lbs Wheel lug nuts 85-105 ft/lbs

Posted on Mar 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have changed cylinder head gasket and need the torque settings for the zd30 nissan engine


try this head torgue link.. that wont highlight

http://www.cylinderheadsaustralia.com.au/torque-settings

the ZD30 is listed half way down the list
and picture of tension sequence

HEAD BOLT TIGHTENING SEQUENCE.
• STEP ONE: 102Nm
• STEP TWO: Loosen All Bolts.
• STEP THREE: 44Nm
• STEP FOUR: +90*
• STEP FIVE: +90*
• IMPORTANT: ALL BOLT THREADS, BOLTHEADS AND WASHERS MUST BE LIGHTLY OILED.
• USING AN OLD HEADBOLT WITH GROOVE CUT DOWN THREAD, CLEAN THE BLOCK HEADBOLT THREADS.




why are these torque setting and sequence
numbers no longer on the VRS head gasket packaging

Oct 28, 2016 | Nissan Cars & Trucks

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

Hi. I am assembling a avanza 1.3 that blew head gasket. What are the torque settings for head bolt


I don't have the specs.Evenly go around to all of the head bolts and gradually torque them. 20,40 60 foot pounds.
Depending on the type of gasket you used,you may have to re-torque the bolts after it has gone through one heat cycle.

Mar 08, 2013 | 2007 Toyota Avanza 1.3

1 Answer

Engine torque settings


Commonly Asked Torque Specs in foot pounds
The main bolts have a torque of 76 lb.-feet and the cylinder head bolts have 62 lb.-feet of torque. The cylinder head studs have 70 foot-lbs of torque, the cam timing gear have lb.-feet of torque, and the cam bearing bolt has 14 lb.-feet of torque.

Crankshaft Torque Specs
  • The stock rod bolts have 46 lb.-feet of torque and the ARP rod bolts have 50 lb.-feet of torque. The crankshaft pulley has 116 lb.-feet of torque, while the flywheel has 80 lb.-feet of torque.


Other Torque Specs
  • The intake manifold and exhaust manifold have 33 lb.-feet of torque each and the oil pan bolts have 9 lb.-feet of torque. The cam timing gear has 58 lb.-feet of torque and the cam bearing bolt has 14 lb.-feet of torque. One set of timing cover bolts have 9 lb.-feet of torque and another set has 29 lb.-feet of torque

Nov 07, 2012 | 1994 Toyota Corolla

2 Answers

What are the torque specs for the Main Bearing Cap bolts on a 1990 CHEVROLET TRUCK C1500 5.7l 350


main caps 85 ftlbs (3divdedsetings30ftlbs all 50 ftlbs all ending at85ftlbs click, rocaps 45ftlbs, head bolts 85ftlbs workingfrom cdenter top ,center botom ,top center working clock wizeand out ,intake boltes45ftlbs again fromcenter working outleft side, right side,left, right 8 bolts one time only or u will distort gasket. oilpan from center alternate L side ,R side,clock wize25ftlbsclick recheck after breakin period valve covers 25ftlbs anrecheck flywheel 90ftlbs ,harmnic balancer bolt 75ftlbs, add oil!!!!run for 15 minutes drain oil &change filter run for 100miles for molly rings 10 mmiles for cast rings .let engine cool down retorque headbolts,replace valve covers .run it and get on it!!! good luck hve fun.

Aug 20, 2012 | 1990 Chevrolet C1500

1 Answer

Need head bolts tourqe sequence for a 89 tercel


1989 L4 headbolt sequence:
Cylinder Head Bolt Torque Sequence809142031993 L4 headbolt sequence:
Cylinder Head Bolt Torque Sequence80914199they appear to be the same,other than the torque angle. good luck!

Oct 20, 2011 | 1993 Toyota Tercel

1 Answer

Whats the proper order and torque specs for a 99 32v northstar head?


REMOVAL & INSTALLATION NOTE: The manufacturer recommends that the entire powertrain be removed from the vehicle before removing the cylinder heads.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Powertrain assembly
    • Intake manifold
    • Cam covers
    • Harmonic balancer
    • Timing chain front cover
    • Oil pump
    WARNING
    Align all timing marks before performing the next step.
    • Chain tensioner from the timing chain
    • Cam sprockets
    NOTE: The timing chain remains in the chain case.
    • Timing chain guides, access for the retaining screws is through the plugs at the front of the cylinder head
    • Water crossover
    • Exhaust manifold
    • Cylinder head bolts by reversing the torque sequence
    • Cylinder head and discard the gasket
    WARNING
    With the camshafts remaining in the cylinder head some valves will be open at all times. Do not rest the cylinder head on a flat service with the cylinder face down, or valve damage will result. NOTE: Clean all gasket mating surfaces. Clean the head bolt holes in the crankcase. WARNING
    Be careful when cleaning aluminum gasket surfaces to prevent damage to the sealing surfaces.
  5. Check the cylinder head for warpage; it must be less than 0.002 in. (0.05mm). If the cylinder head was resurfaced, the dimension between the combustion chamber gauge pad and the deck surface must be at least 10.5mm. To install: NOTE: Refer to Section 1 of this manual for the cylinder head torque sequence illustration. The illustration is located after the Torque Specification Chart.
  6. Install or connect the following:
    • New cylinder head gasket
    • Cylinder head, lubricate the bolts with engine oil
  7. Torque the M11 bolts, in sequence, as follows:
    1. Step 1: 22 ft. lbs. (30 Nm).
    2. Step 2: Turn an additional 60 degrees.
    3. Step 3: Turn an additional 60 degrees (total 180 degrees).
  8. Torque the M6 bolts to 106 inch lbs. (12 Nm).
  9. Set the camshaft timing
  10. Camshaft guide bolt access hole plugs in the cylinder heads. The plugs should be seated and snug
  11. Install or connect the following:
    • Intake cam covers
    • Oil pump
    • Timing chain front cover
    • Harmonic balancer
    • Cam sprockets
    • Chain tensioner to the timing chain
    • Timing chain guides
    • Intake manifold
    • Water crossover
    • Exhaust manifold. Torque the nuts to 22 ft. lbs. (30 Nm) or the bolts to 18 ft. lbs. (25 Nm).
    • Powertrain assembly
    • Negative battery cable Fig. 1: Minimum head resurface dimension 7922vg04.gif

  12. Fill the cooling system.
  13. Evacuate and charge the air conditioning system.
  14. Run the engine and check for leaks.
prev.gif next.gif

Aug 19, 2010 | 1999 Cadillac DeVille

1 Answer

Hi im a mechanic... I have a 2000 Deville with a northstar. Radiator, waterpump, thermostat, are all changed and good. There are no external leaks. I heard the Northstar motors have problems with there...


What happens is the head gaskets shrink causing the headbolts to loose torgue, and the headbolts are of one time use, whenever you do a headgasket job you will need to replace all the headbolts with new ones. and when ever you remove a cylinder head on any engine you should always chase the bolt holes with the proper tap, then blow out the holes with compressed air, this will help to insure a more accurate torque setting on the new headbolts...

Oct 01, 2009 | 2001 Cadillac DeVille

1 Answer

Replacing head


There should be 10 headbolts. This vehicle uses torque to yield headbolts and should be replaced with the new gasket. Bolts 1-8 get torqued to 40 ft lbs initially, bolts 9 and 10 get torqued to 30 ft lbs initially, Then all bolts get turned an additional 90 degrees. I would strongly suggest borrowing a torque angle gauge for doing this or you might be doing the same repair next week.

Feb 12, 2009 | 1999 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...