Question about Cars & Trucks

Open Question

Nissan mistral starter motor bolt - Cars & Trucks

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ZJLimited
  • 17970 Answers

SOURCE: i need to know how to get the bolts off a nissan

Nissan Pick-ups and Pathfinder 1989-1995
Starter - REMOVAL & INSTALLATION
(see Figures 1 and 2)

  1. Disconnect the negative battery cable at the battery, then disconnect the positive battery cable at the starter.
e757468.jpg
Fig. 1: Starter removal on 4WD-6-cylinder engine


4643c02.jpg
Fig. 2: Starter removal on 2WD-6-cylinder engine
  1. On 4wd models with the 6-cylinder engine:
    1. Remove the front gravel shield.
    2. Detach the oil pressure switch connector.
    3. Drain the engine oil and remove the oil filter.
CAUTION The EPA warns that prolonged contact with used engine oil may cause a number of skin disorders, including cancer! You should make every effort to minimize your exposure to used engine oil. Protective gloves should be worn when changing the oil. Wash your hands and any other exposed skin areas as soon as possible after exposure to used engine oil. Soap and water, or waterless hand cleaner should be used.
  1. On 2wd models with the 6-cylinder engine:
    1. Remove the front right wheel.
    2. Remove the front gravel shield.
    3. Remove the exhaust manifold heat insulator.
    4. Remove the exhaust manifold.
    5. Detach the oil pressure switch connector.

  2. Unfasten the remaining electrical connections at the starter solenoid.
  3. Remove the two nuts holding the starter to the bell housing, then pull the starter toward the front of the vehicle and out.
To install:
  1. Insert the starter into the bell housing, being sure that the starter drive is not jammed against the flywheel.
  2. Tighten the attaching nuts and secure all electrical connections to the starter assembly.
  3. Install all remaining components in reverse order of removal.
  4. Reconnect the battery cables. If applicable, refill and check the oil level. Check the starter assembly for proper operation.

Also can check here other DIY.

Hope helped with this (remember rated and comments this help).

Posted on Mar 03, 2010

  • 360 Answers

SOURCE: Dumb question... According to AllData, this is the

Perhaps you're reading more into this than is really there.

The AllData advise sounds accurate, and I'm confident the spirit of the instruction is to perform these initial steps from under the hood (on the top side of the engine). Having completed the initial steps, go under the car and actually physically remove the starter from underneath.

Did you purchase a single vehicle subscription to AllData from AutoZone? The basic subscription is for only one year. For about the same amount of money you can purchase a vehicle specific repair manual and use it until you wear the ink from the pages. I'll take hardcopy over internet any day!

Posted on Feb 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove a starter motor from a 1994 Nissan Torano 2.7 Diesel


Remove the electrical c able at the end of starter, 2 bolts secure starter to engine, remove these withdraw starter, replace Bendix or whatever is fault.

Jan 11, 2015 | Nissan Cars & Trucks

1 Answer

1997 Nissan Mistral Surging


There are 2 bolts underneath the intake manifold that bolt it to the block. Once you remove these, the manifold should come right off.--------------------------------------------------------------------------------------
Launch X-431 IV Auto Scanner

Mar 11, 2013 | Cars & Trucks

1 Answer

Location of starter on 1993 nissan sentra


starter is located on the front side of the motor, easiest way to reach it is from underneath just between the radiator and the motor, two 13mm bolts hold it to the transmission

Jul 26, 2012 | 1993 Nissan Sentra 4 Door

1 Answer

Water pump torque settings terrano2 mistral 2.7td


IMPORTANT
M10 BOLT 27-37 Nm
M8 BOLT 17-23 Nm
good luck barry

May 17, 2011 | Nissan Frontier Cars & Trucks

1 Answer

I am trying to replace the starter in my 86 nissan stanza but cant see it


NISSAN STANZA WAGON - Manual Transmission


Q. Where is the starter on a 1986 nissan stanza station wagon and how do you get to it ?


Due to limited access to the starter, it is recommended that the transaxle be removed when servicing the starter.

REMOVAL:

1. Cold vehicle.

Remove 2 mounting bracket bolts, 10 & 12 mm (Figure 1).

Remove top starter motor bolt 14 mm with universal & long extensions.

Raise vehicle on hoist.

Remove front splash pans 10 mm.

Automatic transmission: Drain 2 qts out.

Remove rt-ft wheel 21 mm., & tie rod (Figure 3), axle cap, cotter pin, adj-nut & rubber washer.

Remove ball joint nuts 17 mm., left lower control arm 19mm. & swaybar bracket 14 mm. (Fig 2).

Remove axle nut 36mm (Figure 4), the front tube, catalytic converter heat insulators 10mm, ctr ex-tube 17 mm., and front tube from exhaust system (Figure 5).

Remove long bolt from ft engine mount (next to radiator), 17mm socket (Figure 6, Item A).

Remove tension rod mount 14 mm. Has adj-bracket with rubber insulators (Fig 6, Items B, C).

Remove right side drive shaft bolts that hold shaft to bracket mounted on engine (Fig7) 12mm.

Remove rt-driveshaft.

CAUTION: Transaxle side seals are cut by spline teeth.

Install hoist type transmission jack and wooden block under the transmission/engine. Be certain the transmission is safely balanced on the hoist.

Remove 5 engine crossmember mounts (3 bolts, 2 nuts) 14mm.

Remove nut that attaches crossmember to engine mount.

Loosen stabilizer bar mounts to allow adequate clearance for crossmember to be removed.

Remove following brackets to allow starter assembly to pass through bottom:

tubular support bracket - engine to transaxle

angled support bracket - driveshaft bracket to engine mount

manifold collector stay - (bottom bolts)

Loosen top bolts, remove bracket above driveshaft-holding bracket 14mm.

NOTE: This bracket is slotted to allow it to slide out without completely removing the bolts.

Remove bottom starter motor mounting bolt.

Separate starter assembly from bellhousing, DC all cables/connectors, remove starter motor.

When installing starter, connect cable, install/torque starter bolts.

Nov 03, 2010 | 1986 Nissan Stanza

1 Answer

Where are the starter bolts located and how do i get to them


Starter bolts go thru thr transmission bell housing which bolts to rear of motor.
1. Jack up car and support on stands.
2. Disconnect BATTERY ground cable.
3. Disconnect starter wiring from starter.
4. Reverse procedure to install.

Feb 08, 2010 | 1991 Nissan 240SX

1 Answer

Howm do I replace a starter on a 1995 Nissan


Nissan 240SX/Altima 1993-1998 Repair Guide

Altima
(see Figures 1, 2 and 3)


ef972ea.jpg
Fig. 1: The starter is located to the left of the oil filter housing on the engine block


dfca7b3.jpg
Fig. 2: The starter motor is removed from the bottom side of the engine compartment


04c206e.jpg
Fig. 3: When installing, be sure to align the starter's mounting bolt holes with those in the engine block
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Remove the starter support bracket, as required.
  4. Label and disconnect the starter electrical harness.
  5. Support the starter from beneath the vehicle using a jackstand.
  6. Remove the starter mounting bolts.
  7. Carefully lower the starter from the vehicle.
To install:
  1. Position the starter on the engine and support it using a jackstand.
  2. Install the starter mounting bolts and tighten to 30-37 ft. lbs. (40-50 Nm).
  3. Connect the starter electrical harness.
  4. Install the starter support bracket, as required.
  5. Lower the vehicle.
  6. Connect the negative battery cable.

Hope helped with this (remember rated this help) Good luck.

Nov 27, 2009 | 1995 Nissan Altima

1 Answer

HOW 2 REMOVE STARTER


Starter motor?
Easy job! Simply
disconnect the battery wires.
Disconnect the solenoid wires at
the back of the starter. (if you don't
know its location, simply trace down the
positive battery cable to where it ends, and
that bulky guy is the starter)
The starter motor i think, is held to the
engine block by 14mm bolts. Remove those
bolts and take starter out.

Oct 29, 2009 | Nissan Pickup Cars & Trucks

1 Answer

Can't get the starter out of a 1991 Nissan pickup.


The second bolt is hidden way up and tucked in near the solenoid. You need to setup a ratchet with extensions/socket (14mm) combination that is just a little longer than the starter motor. If you just can't picture where the bolt is, then go down to the parts store and look at/purchase the replacement starter to see how it mounts up.
There are two bolts for the starter mount and one nut for the main starter power lead. There is one plug for the starter key switch.
Disconnect plug. Loosen lower bolt. Remover upper bolt. Remove lower bolt. Twist starter so you can remove main power cable nut (be sure to have disconnected the battery first!) Pull starter.

Apr 18, 2009 | 1991 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...