Question about Cars & Trucks

1 Answer

Could you please tell me where I can access instructions to assemble a finlandia varpupuu loom? Weaver instructions

Posted by on

1 Answer

Repost in whatever section that seems
appropriate
This is automotive

Posted on Jul 25, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My problem is finding where to connect my cocket wires into the wiringloom in the boot of my cr which is a Renault Laguna 2 2003 diesel. No one seems to have this information. Can tou help. Thank you.


Check with a tow bar fitting shop as there will be a loom that is available for this. You will remove the socket to a light assembly and fit the new loom to the light assembly . then plug the car loom into the new wiring loom and it is all set to go . IF doubtful pay a small bit and have the shop do it for you

Nov 24, 2013 | Cars & Trucks

1 Answer

Problems with bosal towbar wiring kit....


bosal kits
claim to be plug and play to your vehicle
no wires meant to be cut
the wiring instructions might be generic and not truly specific to your C-Max
save time
wire in indicators old school
pick up the left and right indicator wires at the back of the car
make sure there is a good earth on the 7 pin plug

Mar 07, 2017 | Cars & Trucks

1 Answer

Bosal towbar wiring problems....


Did you ever solve the problem with the location for the orange wire as I have exactly the same problem, thanks

Apr 22, 2013 | Cars & Trucks

1 Answer

It's a Nissan rb25det injector loom plug. How do I remove the terminals from it to use the plug on another loom


There is a special tool without it you will ruin the terminal, the best thing to do is buy an assembled repair connector and splice it it on.

Oct 03, 2012 | Cars & Trucks

1 Answer

How do I change fuel filter on a 2005 suzuki reno? Can I find detailed instructions on the internet? Thanks for any help.


You can access the filter, it is part of the pump assembly inside
the tank. You have to remove the entire pump assembly thru the hole under the
back seat. Once that is out, you have to disassemble it as well to access the
filter. It looks like a little semi-circle/half moon shape mesh material. Only
problem is that the dealer does not sell this filter seperately at all. To get a
new one, they will tell u that you have to buy an entire new pump assembly. awcforever_6.jpgTechnically they made it so you don't have to change it. SOrry.

Mar 11, 2011 | 2005 Suzuki Reno

1 Answer

My brake lights don't work when my Head lights are on.


It sounds like a bad earth connection in the vehicle rear wiring loom. Check the earth wire that runs from the globe sockets in the light units and any connectors in the wiring loom near the light assemblies as well as where the earth wire is attached to the body. If necessary, remove, clean thoroughly by removing any corrosion or paint and re-attach securely.

Sep 29, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Schematics for Spark plug wire installation


Hi,

If you are planning on replacing plug wires on a Discovery this solution will help. This task requires minimal tools, with fair to moderate mechanical skills. I'm not going to do a step by step instruction, but just point out some things to be aware of.
1) Coolant pipe in to manifold must be removed. It has a small o-ring you may want to replace . Removal caused minimal coolant loss.
2) You may have to loosen th 8mm bolts at the lower portion of the coil bracket and let it lean towards the firewall, this will allow for easier installation of the air plenum.
3) The black bracket which sits on top of the coil bracket and holds the secondary air pipe can be assembled onto the secondary air pipe loosely prior to installing the air plenum.
4) Wire Loom : Utilize these looms to preset layout order of the wires. Attach to secondary air pipe. This will allow for an easy install into the looms on the rear of the air plenum, since they'll be in order.
5) A little bit of Nye Lubricant on the o-ring for the coolant pipe.


Hope this helps.


Take care..

Aug 06, 2010 | 2001 Land Rover Discovery Series II

1 Answer

Please tell me how to replace a burned out head light, high beam.


To replace the headlamp, turn signal, or parking lamp bulb:This information should be in your owner's manual.
Turn the wheel to access the wheel well.
  1. Remove the fasteners located on the wheel liner. To access the headlamp and the turn signal/parking lamp bulbs.
  2. Reach in behind the wheel well liner and locate the bulb to be changed.
  3. Turn the bulb socket counterclockwise and pull it straight out of the lamp assembly.
  4. Pull the old bulb straight out of the bulb socket.
  5. Push the new bulb straight into the bulb socket until it clicks.
  6. Push the bulb socket straight into the lamp assembly and turn it clockwise to lock it into place.
  7. Reinstall the wheel well liner using fasteners.

Nov 11, 2009 | 2006 Chevrolet HHR

1 Answer

How to take the egnition switch of??


you can access the ignition switch from underneath the dash, but I found it easier to remove the steering wheel, then the instrument cluster. There are two basic elements to the ignition switch. The part that usually breaks down first is the front section, where the key goes into. You have to remove the entire unit from its bracket. Unplug the wire loom from the back of the housing. I believe there are two screws holding both sections together. Remove the screws and replace the unit. Then re-assemble.

Mar 17, 2009 | 1985 Mercedes-Benz 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...