Question about Cars & Trucks

Open Question

How to replace a 2006 suzuki forenza purge valve

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: head light replacement

Hi, I have done this many times before for my 2006 Suzuki Forenza. You will need a 10 milimeter socket wrench for the top two nuts and a 8 milimeter socket wrench for the nut located directly behind the highbeam light. After removing the nuts carfully tilt the head light upward and wiggle out. After moving it halfway, disconnect the two wires connected to the housing. Be careful not to scratch the trim located around the grille. The bulb has a rubber gasket over it. Remove turning counter clockwise. Then, with your index finder slightly push the metal bracket holding the bulb in place down and then release. Install a new bulb making sure not to touch the glass part of the bulb. Reinstall the rubber gasket and carfully put the light housing back into the car. Line up all holes before attempting to replace the nuts. Do not tighten them too much. Only until they are slightly snug. This housing is plastic. So be carful. Then you are finally done. One thing to remember. It's usually better to replace both headlights at the same time for optimum performance. If cost is a factor, one can be done, but you will notice a difference in brightness.

Posted on Aug 22, 2008

Ad
fphandyworks
  • 56 Answers

SOURCE: CANT FIND SPEED SENSOR ON MY 2006 SUZUKI FORENZA

it is located on the hub of the car were the front wheel holds on to the car its a lttle black round looking sensor bolted on.

Posted on Apr 02, 2009

  • 163 Answers

SOURCE: how much freon goes in a 2006 suzuki forenza

You can use those quick fill freon systems from auto zone that has the easy to read Gauge on the bottle. There are some that come with an easy connect hose to.
If you have your own gages and bottle you need to get you pressures right in your high and low side. At most ambient temp. that warrant using your A/C pressures should read about 35 on low side and 65 to 70 on high side.

Posted on May 09, 2009

  • 29 Answers

SOURCE: Where is the transmission range sensor for 2006

Right on the transmission, to the right side of the engine bay as you are looking down on it. It is a black plastic part that is bolted on the transmission with two 10mm bolts, and connected to the transmission with rod and clip. It is partially obstructed by the radiator hose, but otherwise really easy to get to.

Posted on Jan 28, 2010

shaddow4115
  • 105 Answers

SOURCE: need diagram of a fan belt for 2006 suzuki forenza

The diagram should be located under the hood by latch that holds your hood down on either the hood or the support for the radiator.

But hope these help. Also check out navbits_start.gif Suzuki Forums for more info



6a71b98.gif

49c63b2.jpg

Posted on Feb 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where does the 4 oil seals and ten o rings go in the valve cover of a 2006 Suzuki Forenza


flip valve cover over and u should see the four oil seals around the spark plug openings . The 10 O-rings go under each valve cover bolt.

Dec 17, 2012 | 2007 Suzuki Forenza Sedan

1 Answer

P0446


This code is for the Canister purge valve solenoid or if you have filled up your gas tank in the last couple days check your gas cap to see if it installed and tightened this is all EVAP systems part of your vehicle emmisions

Sep 10, 2012 | 2006 Suzuki Forenza

1 Answer

2005 Suzuki Forenza, check engine light is on with fault codes reading P0488 and P0496. Can't get a good explanation of what the cause may be. Any insight would be greatly appreciated.


code P0488 exhaust gas recirculation closed valve pintle error ( EGR Valve ) most likely replace the valve.

code P0496 evaporative emission system continuous purge flow. could be many things, Gas cap, purge valve , purge canister, probably need to have this one check by the dealer.

Jul 01, 2011 | 2005 Suzuki Forenza

3 Answers

How do i replace my TPS on a 2006 Suzuki Forenza?


2006 SUZUKI FORENZA RECALLS/DEFECTS & PROBLEMS Access the National Highway Traffic Safety database of 2006 SUZUKI FORENZA recalls and defects found on 2006 SUZUKI FORENZA automobiles. The National Highway Traffic Safety administration is authorized to order the 2006 SUZUKI FORENZA manufacturers to recall and repair vehicles or parts of motor vehicle equipment when its investigation indicates that they contain serious safety defects in their structure, or performance.
Check with your loacol suzuki for recall not sure on this part but it is a common problem
Good luck

Nov 29, 2010 | 2002 Mitsubishi Eclipse

2 Answers

What is a p0442 code for my 2006 Suzuki Forenza?


P0442 means that there is a small leak in what is called the evap system What it dose is take gas fumes from the fuel tank and divert them to the charcoal canaster to be burned in the combustition system routed through two solinoid valves called the canaster vent valve and the canaster purge valve the vent being from the tankto the canaster and the purge being canaster to the combustion chamber Its a small leak it could be anyware in the system but i would replace the gas cap first many times it starts to leak at the seal and will set this code Its all for emissions and dosn;t have a large effict on over all proformance unless you need to pass emissions

Nov 24, 2010 | 2006 Suzuki Forenza

1 Answer

Replaceing headlight on 2006 forenza?


I had a heck of a time trying to figure this out myself. Finally found a solution thanks to a helpful youtube video. Watch this and you'll be able to change the headlight in your Suzuki Forenza

Jul 14, 2010 | 2006 Suzuki Forenza

1 Answer

Suzuki forenza code is P0496 engine light on


P0496 = EVAP Emission High Purge Flow Fault.

No warranty coverage?
- Likely a sticking purge valve, possibly accompanied by some strange cold idle conditions.
- Possible fuel tank pressure sender with an 'in range' failure-not likely.
- Possible false command from the main processor-not likely.

I suggest try THIS LINK.

Hope helps (remember rated this)

Jun 04, 2010 | 2006 Suzuki Forenza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...