Question about Cars & Trucks

Open Question

Why is my 84 chevy truck stuck in closed loop

I'm working on a 1984 Chevy C10 with a 305. The vehicle is stuck in closed loop and the scan tool shows the knock sensor is retarding the timing from 0 to 45 degrees. There is no knock sensor on this vehicle.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: bad sensor on chevy truck

There are 2 both located in the block..

Posted on Mar 20, 2009

Ad
  • 5 Answers

SOURCE: knock sensor

The knock sensors are located in the rocker valley underneath the intake manifold. GEt a hynes manual to assist you in replacing them. There is acertain tightening sequence when taking the manifold on and off. It is made of a composite plastic so use care and do not over tighten.

Posted on Jul 22, 2009

  • 752 Answers

SOURCE: where are the knock sensors located on a 02 chevy

It is usually below the the cylinder head on the passenger side towards the back of the engine. It has a white single mushroom shaped connector.

Posted on Jan 30, 2010

  • 212 Answers

SOURCE: where is knock sensor located on 2004 chevy 2500Hd

Under intake manifold on top of block,you need to remove intake to access sensors there are two of them you can't miss them when intake is off. After replacing sensors you need a new intake gasket.

Posted on Apr 04, 2010

BCAS1298
  • 3092 Answers

SOURCE: replace knock sensor on 2001 chevy 4.8

You have two knock sensor's, both sit under the in-take magifold on top of the engine, you will have to remove injector rail and in-take.

Posted on Apr 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 84 chevy blazer the driving gears why is there 2 d on the dash which do i drive in


That is a silly question no matter what vehicle you own

I have a 1984 S-10 Blazer for 30 years, so put any
vehicle you drive in D & nothing else

There is NO Automatic Transmission out there that
gets shifted to anything

Aug 31, 2014 | 1984 Chevrolet Blazer

1 Answer

1984 chevy k20 4x4 stuck in low lock


i'm trying to remember my 84 was that the new process 203 or 208 ? on the trasfercase i do believe it has two shift shafts and one of those have to be 1/2 out in like a neutral position for the other to shift from hi and low. do you have manual hubs or automatic on that. Block wheels put vehicle in neutral, climb under trk and check linkage take a hammer and pry bar with you.

Jan 11, 2011 | 1984 Chevrolet Chevy

2 Answers

Knock in right front when turning my 84 chevy c10 truck


this may be a strut or spring or a bearing plate that went bad. if you have 4 wheel drive it may be an front axle shaft.

Mar 30, 2010 | 1984 Chevrolet Chevy

1 Answer

84 chevy running rough


Check the choke when cold. When its hot take notice that its opened. Upon starting next time when its cold look at the choke and see if its closed fully. It should be. If not push the throttle all the way open and let it retract closed. The choke should close when the engine is cold. If it does not the vacuum break is shot which should be the rear one that controls the choke. Yours may be on the front since some are but very few are made on the front

Feb 05, 2010 | 1984 Chevrolet S-10

2 Answers

Can not switch between dual tanks on 84 chevy


isolate your fuel switch and make sure the switch is working and has power if is electric, if not replace the switch. I had to put an after market on mine, then it worked fine.

Oct 26, 2009 | 1984 Chevrolet K2500

2 Answers

How to remove the top for open effect


there are 4 bolts holding the 84 vette top on. two front two rear. There are holes in the top from the inside 2 behind the visors and two at rear. Wrench looks like an allen wrench. There is a tool for the removal which is usually stored in the glove compartment between the seats.

Apr 26, 2009 | 1984 Chevrolet Corvette

1 Answer

Chevy s10


no there is no chip available for your vehicle. your vehicle is not a computer controled high performance type where a performance chip would boost power

Apr 18, 2009 | 1984 Chevrolet S-10

1 Answer

Will a 1993 chevy van G20 series trani w/OD fit in a 1984 chevy van G20 series w/out OD


93 is made to be mated to a fuel injected model with ecm that controls tranny,84 is still old school! best bet have old 1 rebuilt!

Apr 11, 2009 | 1984 Chevrolet Chevy

1 Answer

My fuel gage is stuck at 3/4 of tank in my 84 chevy silverado


take the wire off that goes to the tank and ground it. if the Gage moves then it is the float if the Gage stays there then it is the Gage.

Mar 24, 2009 | 1984 Chevrolet Chevy

2 Answers

84 chevy 4 wheel drive auto hub removial


Remove the cap,look close and you vill see a snap ring inside the ¨pipe¨ take out the ring and then you should be able to pull out the hub.

Jan 06, 2009 | 1984 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...