Question about Volvo S60

1 Answer

Ground wire My radio has interference when engine runs but sounds clear w engine off. How do I fix this?

Posted by on

Ad

1 Answer

Duplicate Question

Posted on Jul 24, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Radio buzz's when onam


you are getting interference from electrical componets you can buy a AM noise filter its cheep 15.00 it plugs in to antenna and has 1 power wire . easy fix.

Sep 30, 2014 | Cars & Trucks

1 Answer

Radio interference


You have a shop put an oscilloscope on the
alternator & look for bad diodes in it.
If that isn't the issue then they some difficult
troubleshooting ahead
Could be a bad fuel pump or hvac motor
Something is putting a frequency on the
electrical bus

Jul 24, 2013 | 2006 Volvo S60

1 Answer

Radio issue


Duplicate Question

Jul 24, 2013 | 2006 Volvo S60

1 Answer

My 2004 Chevy Trailblazer CD play and AM radio works. My FM quit working?


Have you pulled the radio all the way out and make sure the attena is plugged in the unit itself. I would first make sure the new attena's wire is the same exact wire going directly to the stereo unit. Insufficiant grounding of the unit can also cause a weaker signal it will receive b/c it relies on it more as a ground rather than a clear signal receiver and alot of interference and static is transisted instead.

Aug 04, 2012 | Chevrolet TrailBlazer EXT Cars & Trucks

1 Answer

Engine interference in ford falcon


I would suggest you put a radio noise filter on the power lead to the radio. You can buy them from most electronics stores or online. They are called "RF Filters" Also make sure the radio has a good chassis ground and the antenna ground is good.

Jun 12, 2012 | Ford Falcon Cars & Trucks

1 Answer

Noise interference in ford focus when the engine is running


if talking about the in the radio or the speakers it may be a ground wire causing it you can try to grounding the radio or the speakers to see if that will fix it.

Sep 27, 2011 | 2006 Ford Focus

2 Answers

How do I replace the ignition coil in my 2002 ford taurus



Removal & Installation

3.0L (VIN S) Engine

  1. Disconnect the negative battery cable.
  2. Unplug the engine control sensor wiring connectors from the ignition coil and the radio ignition interference capacitor.
  3. Tag and disconnect the spark plug wires from the coil by squeezing the locking tabs, then twist the tab and pull upwards.
  4. Unfasten the four ignition coil retainers and remove the coil and the coil ground wire the radio ignition interference capacitor. Save the capacitor and coil ground wire for re-installation of the coil assembly.
  5. Wipe the coil towers with a clean cloth dampened with soap and water. Remove any soap film and dry with compressed air. Inspect the coil for cracks, carbon tracking, dirt or damage and replace as necessary.

    0996b43f802333d8.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Ignition coil assembly mounting-3.0L DOHC engines


To install:
  1. Place the coil, capacitor and the coil ground wire onto its mounting location on the right hand valve cover.
  2. Install the coil assembly retainers and tighten to 45-61 inch lbs. (5-7 Nm)..
  3. Apply dielectric compound D7AZ-19A331-A or its equivalent to the spark plug wire boots.
  4. Attach the spark plug wires to their proper terminals on the coil and make sure the boots are firmly seated so that the locking tabs engage.
  5. Attach the engine control wiring connectors to the ignition coil and the radio ignition interference capacitor.
  6. Connect the negative battery cable, start the vehicle and check for proper operation.

Dec 19, 2010 | 2002 Ford Taurus

1 Answer

CR-V high pitch sound at speed.


You have a RFI problem that's radio frequency interference. you need and RFI strap for radio to radio attena or an RFI strap from chassis to engine. hope this helps. this is the only way to get rid of unwanted RFI. good luck!

Jul 09, 2009 | 2007 Honda CR-V

2 Answers

Car radio interference on AM


If the radio still does this with the alternator unhooked, I would try changing the plug wires.

Mar 02, 2009 | 1993 Toyota Corolla

2 Answers

Engine missing, car jerking and juddering


you might have a bad plug wire it doesn't have to be loose you could have a hole or cut in the wire and it's not getting a good spark to the cylinder. the radio interferance tells me this might really be the problem

Jan 12, 2009 | 2001 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...