Question about 2006 Toyota Yaris 1.0

Open Question

WHAT ARE THE MAIN AND BIG END BEARING, CYLINDER HEAD AND FLYWHEEL TORQ

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 115 Answers

SOURCE: cylinder head torque settings for a toyota 1493cc

If you have a vehicle application for the motor you can get a Haynes or Chilton manual from your local auto parts store. They usual run around $30.

Posted on Sep 04, 2009

  • 360 Answers

SOURCE: I WANT TO HAVE CYLINDER HEAD TIGHTENING TORQUE AND

Go to a auto parts store (Pep Boys, Auto Zone, Advance, O'Reilly's, etc. ...they all have vehicle specific manuals for sale that will have a section on torque values.

Posted on Dec 26, 2010

FitzOriginal
  • 842 Answers

SOURCE: HI HILUX SURF WITH 2LT DIESEL

Torque Settings Mains = 108NM
Big Ends = 54NM + 90° +90°
Flywheel = 122.5NM
Cylinder Head = 78 NM + 90° + 90°

Valve Settings
Exhaust = 0.40 mm - 0.50 mm
Intake = 0.20 - 0.3 0mm

Posted on Jun 30, 2011

SOURCE: What is the torque settings for : cylinder head

Use a factory service/repair manual. You cannot rely on a possibly wrong answer from this forum.

Posted on Apr 17, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All torque settings on a 4af toyota


cylinder head bolts
stage1-20NM
stage2-40NM
stage3-60NM

MAIN BEARINGS
stage1-30NM
stage2-60NM

BIG END BEARINGS
stage1-25NM
stage2-49NM

FLYWHEEL
78NM

Sep 05, 2016 | Toyota Cars & Trucks

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

Looking for cylinder head, main bearings, big end bearings and flywheel torque settings. Also valve clearence for same engine.


go google and type in - torque settings for (your engine as you haven't given that infomation) and there will be pages of details
There is no flywheel for an automatic. What you have is a flex plate as the torque converter acts as a flywheel

Mar 18, 2015 | Cars & Trucks

1 Answer

What the torque settling on a 1.8spi vauxhall cavalier 1994


Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :
  • Use new bolts and tighten as follows:
      • 1,4/1,6 = 35 Nm + 30° + 15°
      • 1,8/2,0 = 65 Nm + 30° + 15°
  • "Pot"-type flywheel = 65 Nm + 30° + 15°
  • Tighten drive plate to 60 Nm.
Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :
  • Tighten nut in three stages:
    1. 130 Nm
    2. Slacken off
    3. 20 Nm + 80°-90°.
Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

Jan 11, 2015 | Vauxhall Cars & Trucks

3 Answers

I need to kno the cylender head torque specs for a 2.3i vw microbus five cylender


The Audi 5 cylinder engine (Engine code AFU) was mainly produced in South Africa and was called a Microbus. The engine capacity was 2309cc. The Microbus 2.3i T3 was produced from 1992-2002.

According to Mead & McGrouther - Data Digest the torque settings for the cylinder head bolts are as follows: 40Nm + 60Nm + 90'degree turn + 90' degree turn. The cylinder head bolts has to be replaced with brand new ones.

The Main Bearings: 65Nm. The Big Ends: 30Nm + 90 degree turn.

The OHC Bearing Caps: 20Nm.

Flywheel Bolts Manual transmission: 60Nm + 90 degree turn.

Jul 28, 2014 | Cars & Trucks

1 Answer

Torque settings for Nissan na 20 cylinder head


I need the torgue settings for Nissan Hardbody NA20 engine
: Mains bearings, Big ends and flywheel as well as timing belt settings

Feb 11, 2013 | Cars & Trucks

1 Answer

HI HILUX SURF WITH 2LT DIESEL ENGINE CAN I GET CORRECT TORQE FOR. 1-TORQE FOR HEAD BOLT? 2-TORQE FOR CON ROD BEARING BOLT? 3-TORQE FOR MAIN BEARING BOLT?


Torque Settings Mains = 108NM
Big Ends = 54NM + 90° +90°
Flywheel = 122.5NM
Cylinder Head = 78 NM + 90° + 90°

Valve Settings
Exhaust = 0.40 mm - 0.50 mm
Intake = 0.20 - 0.3 0mm

Jun 30, 2011 | Toyota 4Runner Cars & Trucks

2 Answers

Mitsuibishi pajero 4m40 engine measuement of torque setting


Cylinder head (renew bolts)

stage 1 50nm
stage 2 100nm
stage 3 slacken of 360"
stage 4 tightn 50nm
stage 5 90"
stage 6 90"

stage 7 tighten the M8 bolts (the smaller ones) 24nm

Main bearings

20nm
90"
90"

Big end bearings

50nm
90"-100"

flywheel 125nm-135nm

Feb 10, 2011 | Mitsubishi Montero Cars & Trucks

Not finding what you are looking for?
2006 Toyota Yaris 1.0 Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...