Question about 1999 Chevrolet Venture

1 Answer

Wiper remains on after the combation switch is off

Wiper remains on after the combination switch is off

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Your switch could be faulty or bridged try changing the switch

Posted on Jul 24, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 toyota camry windshield wipers won't work


First I would look in the fuse box by the driver side and check the fuse,if good then get a meter and see if power is going to wiper motor,if so,then wiper motor is bad,if no power is going to motor,then bad switch,here's a link to see. Repair Guides Windshield Wipers And Washers Windshield Wiper Motor...

Windshield Wiper Switch

Print
REMOVAL & INSTALLATION
The windshield wiper/washer switch is part of the Combination Switch Assembly. Refer to Turn Signal/Combination Switch services procedures.

Oct 18, 2014 | 2000 Toyota Camry

1 Answer

Wipers


l,do not know much about that l advise you contact a qualify service personal

Jul 24, 2013 | 2007 Chevrolet Optra 1.6

1 Answer

Replace combination wiper switch 2002 Pontiac Bonneville


I just pulled one of these switches from car. You need a t20 torx bit and a flat head screw driver. Disconnect the negative terminal under the backseat so the airbag doesn't go off, the steering wheel doesn't need to be pulled.

Jul 23, 2012 | 2002 Pontiac Bonneville

1 Answer

Where is the wiper switch in a 1998 mercury mountaineer. Replaced the wiper motor but the wipers still only work on high speed


The wiper switch is on the steering column ands part of the turn signal switch, it is called the combination switch.

Jan 25, 2012 | 1998 Mercury Mountaineer

1 Answer

Wind shield wiper blowing fuses


You have a short circuit to ground when the switch for the wipers is turned on. It does absolutely no good to keep replacing the fuse until the short circuit has been located and repaired. I guess you are just starting to figure this out five fuses later.

The lesson here is that fuses do not cause electrical circuit failures. Electrical circuit failures cause blown fuses. There are many people that do not understand this.

If the fuse remains intact until you turn the switch on, you will find the problem between the wiper (combination) switch and the wiper motor assembly or the wiper motor itself.

Nov 23, 2011 | 2004 Kia Sorento

2 Answers

My windshield wipers will not turn off and I have no turn signals.


I think your combination switch is malfunctioning. The switches that control both the wipers and the
turn signals are built into the combination switch. And the headlight controls too on some cars.

Your car may have a switch that controls the wipers and the turn signals, but not the headlights.

But whether you have the type that controls wipers/turn signals/headlights or just turn signals/wipers Im not sure, you didnt mention the specific year and model. But you should replace the switch that controls your wipers/signals. They are expensive sometimes, especially if you have the combo switch that controls wipers, headlights and turn signals. But you can find one at a slavage yard for a lot less money than new.


But you should put the year/model of your car when you post a problem youre having. That makes it more likely that someone can help.

Sep 10, 2011 | Chrysler Town & Country Cars & Trucks

1 Answer

My wipers stopped working! the washer fluid sprays, but the wipers won't do anything. also, my power locks haven't been working for months.


check the fuse firdt if this is ok disconnect the wiring plug from wiper motor and check if this has power when combination switch wiper section is in on position if it does wiper motor has failed if not is probably wiper arm section of combo switch faulty.

Mar 09, 2011 | 1996 Honda Civic

1 Answer

How do i remove the turn signal switch from a 1984 nissan 300zx?


What you really want to remove is the "Combination Switch" which controls the
a) headlights b) turn signals, and c) windshield wipers.
The new switch comes with the Left-hand handle attached (expect to pay $$$).

I found your solution (with illustration and replacement parts) at
www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c15280071fa4
Autozone will expect you to register with the site - free. Since your car is a 1984, buy
a Haynes manual - $20 anywhere (try Pep Boys, Advance Auto Parts, etc.)

(I don't work for Autozone) Autozone sells 2 replacement switches:
the one you want is: Duralast SW1836 $122.99 - it has the combination switch and handle only.
They also sell: Duralast SW1690 $170.99, which has the combination switch/handle and also a
collar going around the steering wheel and another switch and handle on the right side of the column.

1. remove steering column cover.
2. unfasten the wiper switch electrical connector.
3. remove the wiper switch-to-combination switch retaining screws, then pull the wiper switch off of the combination switch.
4. The combination switch is now disconnected and can be removed.
5. Installation of new part is reverse of removal.

Oct 13, 2010 | 1984 Nissan 300ZX

2 Answers

My windshield wipers (front) on a 2000 dodge grand caravan go off and on on their own. They wont work most of the time but they will just pop on on their own or if u turn the lights or high beams off and...


My best guess is the switch is bad. Did you replace it? The problem could also be the bcm, but I would test the switch first. Remove it and check it with an ohmmeter.

0996b43f80239143-xpf45b2xmdrdbg0gt251xk4c-1-0.gif

Turn Signal Switch

CAUTION
The Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the air bag or SIR system wiring. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.

  1. Disconnect and isolate the negative battery cable from the battery.
  2. In order to disarm the air bag system, allow the system capacitor to discharge for at least 2 minutes, before performing any removal procedures.
  3. Remove the upper and lower steering column shrouds.
  4. Disconnect the electrical connector from behind the combination switch.
  5. Remove the mounting screws securing the combination switch to the steering column adapter collar.
  6. Remove the combination switch from the vehicle.
To install:
  1. Install the combination switch to the steering column adapter collar. Tighten the combination switch mounting screws.
  2. Reconnect the electrical connector to the combination switch.
  3. Install the upper and lower steering column shrouds and tighten the retaining screws.
  4. Reconnect the negative battery cable and check all functions of the combination switch for proper operation.

0996b43f80232fdd-xpf45b2xmdrdbg0gt251xk4c-1-2.gif

Jul 25, 2017 | 2000 Dodge Caravan

1 Answer

THE AUTO DOOR LOCK AND POWER WINDOW DO NOT WORK AND I CANT FIND THE FUSE FOR THEM ON 2005 NISSAN ALTIMA


From the service manual, which is available relatively inexpensive at Promanuals.net here

 Both front wiper relays are located in the IPDM E/R (intelligent power distribution module engine room)
 Wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input terminals.
Terminal combination status is read by BCM (body control module)
 BCM controls front wiper LO, HI, and INT (intermittent) operation
 IPDM E/R operates the wiper motor according to CAN communication signals from the BCM.
Power is supplied at all times
 through 50A fusible link (letter f , located in the fuse and fusible link box)
 to BCM terminal 70, and
 through 20A fuse (No. 39, located in the IPDM E/R)
 to front wiper relay, located in the IPDM E/R
With the ignition switch in ON or START position, power is supplied at all times
 through 10A fuse [No. 1, located in the fuse block (J/B)]

Sep 28, 2009 | 2005 Nissan Altima

Not finding what you are looking for?
1999 Chevrolet Venture Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...