Question about 2003 Toyota 4Runner

Open Question

Where are the vsc switches or sensors located on 2003 4runner

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The vsc trac sensor location on a 2002 Toyota sequoia


A speed sensor failure in the rear axel housing has damaged friction plates in the differential (limited slip). This axel should have had oil serviced at 80,000 miles

Jun 02, 2017 | Toyota Cars & Trucks

1 Answer

How do you fix code p1589 in Toyota Vitz?


P1589- Acceleration sensor learning.
Zero Point Calibration Using Jumper wire

The following manual procedure may be used in the cases where a Diagnostic Tester is
not available.

CAUTION:
While performing the Zero Point Calibration, do NOT tilt, move, or shake the vehicle.
The vehicle must remain in a stationary condition throughout the entire process.
Be sure to perform the procedure on a level surface with an inclination of less than 1%.

1. If the vehicle is equipped with A/T, ensure that the shift lever is in the "P" range and
the parking brake is applied. If the vehicle is equipped with a M/T, ensure that the
parking brake is applied.
2. Turn the ignition switch ON.
3. Using the SST, repeat a cycle of short and open between terminals Ts and CG of
DLC3 4 times or more within 8 seconds (refer to the specific vehicle EWD for TS and
CG pin location in the DLC3).
4. Verify that the VSC indicator light is lit indicating the recorded zero point is erased.
5. Turn the ignition switch OFF.
6. Be sure the terminals Ts and CG of DLC3 are disconnected.
7. Turn the ignition switch ON.
8. Check that the VSC warning light goes off about 15 seconds after the ignition switch
is turned ON.
9. After ensuring that the VSC warning light remains OFF for 2 seconds, turn the ignition
switch OFF.
10. Connect terminals Ts and CG of DLC3 using the SST.
11. Turn the ignition switch ON.
12. After turning the ignition switch ON, check that the VSC warning light is lit for about
4 seconds and then starts quick blinking at 0.13 second intervals.
13. After ensuring the blinking of the VSC warning light for 2 seconds, turn the ignition
switch OFF.
14. Remove the SST from terminals Ts and CG of DLC3.
15. Drive the vehicle for at least 5 minutes to confirm Zero Point Calibration is complete.
IF FAILED REPLACE THE BRAKE ACTUATOR - SKID CONTROL ECU.

Jan 18, 2016 | Toyota Cars & Trucks

1 Answer

How to repair steering angle sensor


Zero Point Calibration Using Jumper wire
The following manual procedure may be used in the cases where a Diagnostic Tester is not available.
CAUTION:
While performing the Zero Point Calibration, do NOT tilt, move, or shake the vehicle. The vehicle must remain in a stationary condition throughout the entire process. Be sure to perform the procedure on a level surface with an inclination of less than 1%.
1. If the vehicle is equipped with A/T, ensure that the shift lever is in the "P" range and the parking brake is applied. If the vehicle is equipped with a M/T, ensure that the parking brake is applied.
2. Turn the ignition switch ON.
3. Using the SST, repeat a cycle of short and open between terminals Ts and CG of DLC3 4 times or more within 8 seconds (refer to the specific vehicle EWD for TS and CG pin location in the DLC3).
4. Verify that the VSC indicator light is lit indicating the recorded zero point is erased.
5. Turn the ignition switch OFF.
6. Be sure the terminals Ts and CG of DLC3 are disconnected.
7. Turn the ignition switch ON.
8. Check that the VSC warning light goes off about 15 seconds after the ignition switch is turned ON.
9. After ensuring that the VSC warning light remains OFF for 2 seconds, turn the ignition switch OFF.
10. Connect terminals Ts and CG of DLC3 using the SST.
11. Turn the ignition switch ON.
12. After turning the ignition switch ON, check that the VSC warning light is lit for about
4 seconds and then starts quick blinking at 0.13 second intervals.
13. After ensuring the blinking of the VSC warning light for 2 seconds, turn the ignition switch OFF.
14. Remove the SST from terminals Ts and CG of DLC3.
15. Drive the vehicle for at least 5 minutes to confirm Zero Point Calibration is complete

Jul 24, 2014 | 2012 Toyota 4Runner SR5 4dr SUV 4.0L V6...

1 Answer

Enable vsc on 2001 lexus gs430


the VSC is reading only when is dissabled

Jun 07, 2017 | 2001 Lexus Gs 430

2 Answers

My Toyota Sienna shows VSC light on the broad. What Should I do?


Hi there,

If you've had your vehicle computer codes read and determined no issue with the VSC circuit, then you just need to cancel the warning light.

I've made up the following instructions, on how to clear VSC & TRAC Warning lights:



Zero Point Calibration of Yaw Rate and Deceleration Sensors Using Paper Clips (or jumper wires).

First, locate the 16-pin ODB II connector under the steering wheel (beneath the dash). The pins are numbered sequentially backwards from right to left (from the wide side of the connector looking at it from underneath).


Take two normal-sized paper clips (or suitable jumper wires). If using paper clips, straighten one edge of one of the paper clips. For the other, bend it open to a 90-degree angle (like an elbow).


Insert one paper clip/wire into pin # 14 (Ts), and the other paper clip/wire into pin # 4 (CG) of the OBD II connector - DO NOT allow the paper clips/wires to make contact at this point.
Refer to diagram below:

wolfman304_13.gif


1. Ensure the shift lever is in "P" range.


2. Turn the ignition switch to "ON" (not start).


3. Momentarily touch the two paper clips/wires together (short) and separate again (open) - Repeat this process 5 times (within 8 seconds of turning ignition on).

Verify that the VSC indicator light is illuminated, indicating the Recorded Zero point is erased.


4. Turn the ignition switch "OFF".


5. Remove both paper clips/jumper wires from the OBD II connector.


6. Turn the ignition switch "ON" (not start) - wait until VSC warning light turns off (approx. 20 seconds), then wait 2 seconds.


7. Turn the ignition switch "OFF".


9. Re-insert paper clips/jumper wires to terminals #4 & #14 of the OBD II connector (as per above diagram).


10. Turn the ignition switch "ON" (not start) - VSC warning light should remain illuminated for 4 seconds, then start flashing at 0.13 second intervals.


12. After VSC warning light flashes for 2 seconds, turn the ignition switch "OFF".


13. Remove paper clips/jumper wires from the OBD II connector.



Drive your vehicle to confirm VSC & TRAC warning lights have been reset and no longer illuminate.




"If this has helped you resolve your issue, please be kind enough to leave a testimonial"



Jun 10, 2011 | 2001 Toyota Sienna

2 Answers

I had the master cylinder replaced and a leaking caliper replaced. As soon as I left the shop both VSC off and VSC Trak lights were illuminated on my 2004 Toyota Sequoia. Brake repair shop said it had...


this could have been caused by the replacement of these parts. the system could have air in it still they could have forgotten one of the sensors or sensor ring. low fluid levels might also cause this.
try this pull the positive cable from the battery and let sit for 2 to 3 minutes then reconnect the cable and see if this resets the monitorinbg from the computer. i agree that coincidence of the repair would be suspect. most auto parts stores will also hook a computer to your car for free to diagnois what parts are needed this is a quick way to see if something is missing.

Nov 18, 2010 | 2004 Toyota Sequoia

2 Answers

The VSC and Check engine light turn on for lexus 1999 the cood is p0500


Toyotas and Lexus cars have some unique feaures. If your fuel cap is loose or the O2 sensors on the exhaust are faulty this results in an emission problem and the engine computer unit (ECU) engages the check engine light and disables the VSC (the VSC light comes on to warn you that it has been disabled). However you have p0500 code which says the car has no speed sensor signal. The seed sensor is located on the side of the final drive from the transmission and its job is to measure the speed of rotation of the output shaft. The ECU will compare the signals from this shaft along with the speed sensors in the wheel hubs. If there is a difference between these signals the VSC is engaged to apply braking effort to which ever wheel is slipping (running faster) than the other or that the transmission speed sensor would warrant.
So you either have an emission fault has fed back to the VSC and speed sensor missing (p0500) condition, or you have a faulty sped sensor which has tripped the VSC light and in turn the CEL.
Check your fuel filler cap is on tight, turn radio off and disconnect the negative lead to the battery for 5 minutes (this should clear the ECU memory of the code error). If p0500 error and CEL and VSC lights come back on then check the electrical connection to the speed sensor. Ensure it is clean and making a good contact, check the wiring for continuity. If everything else looks good consider changing the speed sensor.

Sep 14, 2010 | 1999 Lexus ES 300

3 Answers

2001 toyota avalon engine and vsc light stays on


You have to use a scanner and pull the code out that is causing the check engine light to come on. whatever code/codes you find are probably related to vsc light.
Good luck and keep me posted

Mar 09, 2010 | 2002 Toyota Highlander

3 Answers

2004 Toyota 4Runner, Regarding The VSC TRAC and VSC OFF lights


Check your switches for the VSC, some get bumped on (due to their location) and some get stuck in the "on"position.

Aug 04, 2009 | 2004 Toyota 4Runner

1 Answer

Vsc vsc off check engine light on 2000 toyota avalon I have the same problem on my 2006 Avalon Limited. Error code indentifies the O2 Sensor located on Bank 1 Sensor 1 as defective.


Disconnect your battery for 10 minutes after which you connect it back the lights should go off. Don't report to toyota. Nigerian style!

Rate this............

Mar 21, 2009 | 2007 Toyota Avalon

Not finding what you are looking for?
2003 Toyota 4Runner Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...