Question about 1996 Toyota Land Cruiser

Open Question

ECU needed 89661-60250

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the ecu located on a 2004 nissan maxima 3.5 sl


This is a copy/paste from a Nissan forum:

C/P

The ECU is located on the floor directly behind the radio. You do NOT need to remove any glove box, dash, or vents to access it. There is a black plastic cover with 2 round plastic snaps that cover the ECU. From the driver's side, the cover is directly beside the gas pedal. Pull on the cover to remove it, and there is the ECU. The ECU has (4) 8mm screws that hold it to the mounting bracket. Then it slides out towards the passenger's side.

As for the part number, you need the Consult-II to get it. But you also need a code that is written on top of the ECU if you are looking for a junkyard spare. You can see this code from the passenger's side without removing the ECU from the mounting bracket (You will need a flashlight). The number should be A56-***-** or something like that.

Sep 22, 2015 | 2004 Nissan Maxima 3.5 SL

1 Answer

Will toyota corolla 1800 with 1zz motor run with 1600 3zz ecu.


The settings would be completely different - you will need the 1.8 ECU

Dec 23, 2014 | 2006 Toyota Corolla

1 Answer

No voltage to throttle body on a suzuki samuri


this this all stock car, as most sammi are vastly modified, now.
common mod is put in Sidekick G16B engine.
so is it stock 1.3L?
that be first question, and if car is EFI and is stock or G16
the TPS needs 5vdc from the ECU.
if the ECU 5vdc ref pin is dead there are only 2 causes.
1: ECU bad.
2: this line is shorted.

1992 had 3 engines. 1.3 , 1.6 TBI and 1.6 MPI
throttle body or Multipoint injection (4 injectors) vastly different.
ECU TBI , pin a23 is 5vdc, if the map shorts, this can blow out the 5vde regulator,
ECU MPI. pin B6 runs only the TPS. sensors. (simple)

best practice here is to post displacement of engine,
and ECU part number. ECU suffix is all we need. and bingo.
I have all Suz, part. number, in my book. for all parts and all ECU.
(usa and canada)

The ECU shops (cardone is tops in USA) the first test
is the 5v pin, #1 off the dime. that.
the Sidekick ECU 8valve ECU. TBI , the 5vdc pin loves to burn the
pcb trace to kingdom come.
see that here.
examples see suz, page for 5v
http://www.fixkick.com/ECU/ecu-8v-sig-list/e76.jpg

see blown trace
the trace in front of this zener diode blows.
(usually customers hot wiring stuff (evil)
http://www.fixkick.com/ECU/5vdc-Refr-supply/56B30-5VDC.jpg

the acutal blown trace (and zener blown too)
is here see it, (if real sammi, it will be i different loc.)
this is a Sidekick G16A TBI ECU. 56Bxx
http://www.fixkick.com/look/ECU-secrets/images/33920-56B30_B15_damaged_trace-B15.jpg

how is that?
need more , ask /?

id bet cardone didnt check your ecu, (some fleabayer?)

Feb 14, 2014 | Suzuki Cars & Trucks

1 Answer

How do i replace ECU/ECM on 1996 toyota celica?


if it is just the fuel problem with the ecu, replace the chip in side the ecu from the new one you got as then you dont need to re program it then. the fuel chip and control is inside the ecu. you used to be able to get the chips for them and program the codes onto them. should be clip in type chips. if its soldered type as there are 2 types of ecu boards with same part number. you will need to un solder the chip.

Dec 20, 2013 | Cars & Trucks

2 Answers

Fault with ecu


fault with an ecu, ecu's can be fixed the only thing you need it the software putting back on it. some ecu are at fault as it may have had a glitch and lost some of its functions this can be fixed with a reprogram. some ecu after a time need to be updated. some ecu's are now automatically updated via a gsm network using the original radio your manual will tell you if this is fitted.more common faults with an ecu is not the ecu at all and a bad sensor engine knock sensors have been know to turn off the ecu. some engine are fitted with none start if the cat sensor has failed.limp mode is activated when the cam sensor or crank sensor has failed. some models if the egr has failed can put engine in limp mode or turn off the ecu. if a ecu fails for a none sensor related problem then the ecu has come under a fault, software or voltage. some of the old ecu were fitted with a temperature sensor either inside or on the case on the out side of the ecu. these can fail and will need to be replaced.

Aug 10, 2013 | Vauxhall Cars & Trucks

1 Answer

I replace the engine on astra 2001 and no start no power on the spark plugs and i cant read the ecu with tester


you need to have the original ecu and sensor on the engine. you have replaced. if you have changed the ecu put the original one back on as it is paired to the car and only your car. if you want to change the ecu you need to change every box, ecu. immobiliser . alarm. ignition. or you need the pass code for the car so you dont need to do this but this can cost alot.

Sep 08, 2012 | Opel Astra Cars & Trucks

1 Answer

Instructions for replacing 1997 Jeep Wrangler 6cyl


Its an easy job! Disconnect the battery first! That's very importand! Then disconnect the wiring pack from the ECU. Some models are equipt with snap-systems, other with a screw-system to remove the wiring connector from the ECU. If done, there are three or four screws that hold the ECU in place with the body. Remove the screws and you hold the ECU in your hands. To buy a new or rebuilt ECU, reffer to the numbers shown on the label at your Wranglers ECU in combination with the V.I.N. To connect the new ECU with the wiring pack, be careful with the connector! You need to put him in the right position to connect with the ECU. Do it slow and make sure the connector fits to all points. Otherwise you'll bake some contacts inside the connector.

Oct 23, 2009 | 1997 Jeep Wrangler

1 Answer

Blown ecu fuse


ECU= Electronic Control unit. This is what controls all the engine electronics. All the sensors on the engine and other things are routed through the part. What it does is tells the engine how to run. Each sensor plays a specific role. The ECU reads how much are the engine is getting, tells the engine how much gas it needs, etc. Try digging around a salvage and finding a new ECU. Swap it out, and if it is still blowing the ECU fuse then you need to start looking for shorts.

Aug 19, 2009 | 1998 Hyundai Elantra

2 Answers

Location of ECU


Check under drivers seat.

Feb 13, 2009 | 1992 Honda Accord

2 Answers

Electrical diagram


Hi,

Might this help?
They were originally posted here and here.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Aug 16, 2008 | 1992 Toyota Celica

Not finding what you are looking for?
1996 Toyota Land Cruiser Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...