Question about Cars & Trucks

Open Question

2007 yukon denali what resistor would I use to bypass the air ride compressor I read 18 ohm but can't find wattage all four corners have resistors but the pump still comes on for about 5 seconds at start up.pump sounds terrible. If I unplug it it sets a error message for ride control

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 2004 yukon xl denali self-leveling rear air shocks

There's a lever that connects the driver-side rear shock to the Automatic Level Control module (the air compressor and the ride-height sensor). Disconnect the lever from the shock and rotate it up and hold it. The compressor should kick in when you hold in place after a few seconds. If it doesn't kick in, make sure your fuses and relays are good. Otherwise, you may have a failed ALC module/burned out air compressor (from the shocks being shot). After you replace the shocks (and after you recouped from the heart attack you had when you shelled out $500+ for each shock), replace the ALC module/compressor (it's all one unit), and test it - it should kick on when you rotate the lever up again.

Figure about $350 for the ALC module from your dealer, and make sure the part numbers match! Your truck came with an upgraded ALC module from the 2001-2004 module, which were prone to water damage.

Good luck!

Posted on Dec 30, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the air compressor for the ride control on 06 gmc denail


Ride control compressors burn up because of leaking air line or shocks. Replacing compressor won't last long if you have a leak. Most of these units are mounted under floor near rear axle.

Feb 15, 2014 | 2005 GMC Yukon Xl Denali

1 Answer

Air ride air compressor not working 2003 yukon denlia


On your 2003 yukon denali, the air ride compressor is located on the driver side rear frame rail on the outboard side, near the fuel filler neck and behind the left rear wheel. Hope this helps!

Jul 24, 2009 | 2003 GMC Yukon Denali

1 Answer

Where is the blower motor resistor on a '95 yukon


I am pretty sure that a 95 and 99 are the same. On a 99 Yukon the blower motor resistor pack is on top of the air box. Remove the glove compartment door, the blower itself will be on the right side. All the way to the far left on top of the air box there is a plug. Unplug and remove the 2 small screws. With some manipulation the resistor pack will lift out. Hope this helps keep me posted, be glad to help. 

Jul 04, 2009 | 1999 GMC Yukon Denali

1 Answer

1999 yukon denali front blower motor not working


Check Fuse #3 in the under hood fuse block it is the only common connection I can make.

Jun 28, 2009 | 1999 GMC Yukon Denali

3 Answers

2005 gmc yukon xl denali service ride control


it has to do with your air ride suspension best bet is take it to the dealer there is probably a problem with a level sensor. hope this helps you

Mar 16, 2009 | 2005 GMC Yukon Xl Denali

6 Answers

My autoride suspension is not working


A ton of things could be wrong with your autoride system. If you have more than about 70k miles and haven't replaced the rear shocks ($500+ EACH!!! at the dealer), then they are probably leaking out. If they leak out, then the air compressor will always run. Eventually the air compressor/ride level sensor module (located on the driver side rear wheel on the inboard side of the frame, $300+ at the dealer) burns out because it's not designed to run at 100% duty cycles. After the air compressor burns out, the Electronic Stability Control module (in an XL, located inside the passenger side rear wheelwell trim, next to the third row seat, $300+ at the dealer) will probably short out. If your autoride isn't working and you don't get a "Service Stability" message, your ESC module is probably going bad.

It is possible to convert to regular shocks, but to keep the Stability Control (still has to control your brakes and front variable dampening shocks during "evasive" maneuvers), you have to insert some 1/4 watt resistors in to the ride height sensor connectors (can't remember what values, but I'm sure you can Google that) so that the Stability system doesn't throw a code. Not that it matters, but the message can get annoying if it's always there to nag...

My dealer quoted over $2500 to replace the entire system. I figure I can find the control modules from my local junkyard for $300, and the shocks from ebay for $350 for the pair. Be sure to match all of the GM part numbers, and keep an eye out for an upgraded Air Compressor module - GM released an update that is heavier duty and more water-resistant than the first design. I don't remember the part number, but my dealer included the upgrade with my quote.

Oh, and the only "easy" way to test the modules is with a Tech 2 tool. Otherwise it's lots of testing with a 12-volt source and a couple of multimeters and oscilliscopes...

Good luck!

Sep 03, 2008 | 2005 GMC Yukon Xl Denali

3 Answers

2004 yukon xl denali self-leveling rear air shocks


There's a lever that connects the driver-side rear shock to the Automatic Level Control module (the air compressor and the ride-height sensor). Disconnect the lever from the shock and rotate it up and hold it. The compressor should kick in when you hold in place after a few seconds. If it doesn't kick in, make sure your fuses and relays are good. Otherwise, you may have a failed ALC module/burned out air compressor (from the shocks being shot). After you replace the shocks (and after you recouped from the heart attack you had when you shelled out $500+ for each shock), replace the ALC module/compressor (it's all one unit), and test it - it should kick on when you rotate the lever up again.

Figure about $350 for the ALC module from your dealer, and make sure the part numbers match! Your truck came with an upgraded ALC module from the 2001-2004 module, which were prone to water damage.

Good luck!

Aug 28, 2008 | 2005 GMC Yukon Xl Denali

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...