Question about Cars & Trucks

Open Question

How to remove the driver side front fender on a 1994 ford f150

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

handybc70
  • 25 Answers

SOURCE: Front fender removal

Hiya... here's the details of fender removal/installation:
the left-side (same for right-side) fender has 6 bolts attached to the "sidebody" frame.
The bolt location:
3 are on the top fender-easy to find when hood is open,
1 is hidden at the rear of top inner fender-just open the left-front door wide to find it (early equinoxes had foam-like noise absorber material in it, just remove it from underneath fender after the wheelwell liner is removed),
1 bolt is hidden at bottom of front fender area at headlight/bumper area-you need to remove plastic wheelwell liner to gain access,
1 bolt is hidden at bottom of rear fender area where the black plastic rocker panel meets below the fender...
THIS area is probably the most difficult task to do since it requires you to remove a small bolt found on the front of rocker panel behind the front-left wheel then use a flat screwdriver or clip removal tool to pry open the black plastic **clip's 'dime-sized' head prior to pull out the clip's body (it has 8 clips underneath the chassis) then use your hands to grasp the rocker panel underneath, pull it down-toward you...this should do it....USE CARE during rocker panel and clip removal/installation so you don't break the clips!
It also has yellow plastic clips inside the rocker panel (used as a guide during installation into rocker sill holes-use caution not to break it)
**note: early equinoxes had rocker panel clips that you can actually pull it out from the hole, while later equinoxes has 'built-in' clips inside rocker panels that you don't see the clip heads below it due to engineering part design change**
Be sure to exercise care when handing this task!

808b156.jpg

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the driver side front fender on a 92 chevrolet s10 pickup?


remove the driver side front fender Teeta, Removing fender on your truck, Check the attached links,instruction and guides may be not identical but really close to yours. Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
1994 to 2003 Chevy 10 GMC 15 Blazer and Jimmy Left Front Fender...
http://www.s10forum.com/forum/f137/s10-fender-removal-457021
http://www.automotiveforums.com/t561502-need_help_on_removal_of_front_fender_my_91_s10_blazer.html
S10 Fender Removal eHow

Jun 24, 2016 | Chevrolet Cars & Trucks

1 Answer

1993 Ford f150, driver's side door catches on the front finder when you try to open it


Fender needs adjusted. Loosen the bolts on top, pry the fender forward, hold it there and tighten the bolts. There should be about 1/4 inch gap between the fender and door.

Jun 28, 2015 | Ford Cars & Trucks

1 Answer

How to remove in cab bolt front fender f150


remove the inside side trim ( near the foot and inside holes you will find nuts or bolts that will unscrew to allow the fender removal

Dec 16, 2014 | 1993 Ford F150 SuperCab

1 Answer

How change front fender f150 2000


Fender -Front Removal
  1. Remove the radiator grille opening panel reinforcement (8A284).
  1. If equipped, remove the front wheel opening moulding.
    1. Remove the pin-type retainer.
    1. Remove the screws.
    1. Remove the wheel opening moulding.
    sy1~us~en~file=n12124a.gif~gen~ref.gif
  1. Remove the front fender splash shield (16103).
    1. Remove the screws.
    1. Remove the pin-type retainers.
    1. Remove the front fender splash shield.
    sy1~us~en~file=gn2615a.gif~gen~ref.gif
  1. Remove the cowl grille.
  1. On RH front fender, remove the antenna mast.
    sy1~us~en~file=k21762b.gif~gen~ref.gif
  1. On RH front fender, remove the antenna base.
    1. Remove the radio antenna base cap (18A927) by gently inserting a thin straight-edged screwdriver underneath the cap and carefully following inside the perimeter until both snaps are free.
    1. Remove the screws.
    1. Lift the antenna base.
    1. Disconnect the radio antenna lead-in cable (18812) and remove the antenna base.
    sy1~us~en~file=k22299b.gif~gen~ref.gif
  1. Remove the fender stuffer.
  1. Remove the stone guard.
    1. Remove the pin-type retainers.
    1. Remove the stone guard.
    sy1~us~en~file=gn2618a.gif~gen~ref.gif
  1. Remove the front fender.
    • Remove the bolts.

Sep 17, 2014 | 2000 Ford F150 Flareside SuperCab

2 Answers

1996 f150 will not start


Hi:) If the engine will turn over but not fire up Check to spark module on the side of the distributor and check to make sure it is getting fuel from the fuel pump in the tank and the fuel relay on the drivers front inner fender. If the engine won't turn over check the solenoid and starter. And check for corroded green wire while you are check everything else.

Mar 16, 2011 | 1996 Ford F150 Regular Cab

1 Answer

How to replace ignition control module on a 1994 ford f150


Depending on your engine, if its located on the distributor remove the two screws/bolts that secure it pull downward to take it off, then slide the new one upward and put your screws/bolts back in, if you have the ignition module on the driveside fender same instructions.

Jan 19, 2011 | 1994 Ford F150 Styleside Supercab

1 Answer

After replacing a back tank on 1994 ford f150xlt truck it will not start and check engine light is on can't find the reset button or locate the correct relay in the engine to check if its blown no manuel


If the check engine light is on, there may be something else wrong with it, the relay for the fuel pump is on the drivers side fender it should be labeled. One says EEC, TOW and FUEL.

Sep 06, 2010 | 1994 Ford F150 Styleside Supercab

1 Answer

1994 Mercury Topaz Fender Removal


Harbor Freight and most local body shop supply stores should have a suction-cup type tool for pulling out dents. You maybe able to remove the inner fender well to get to the dent. To remove the fender, you'll need to remove the top fender bolts, the bolts that attach it to the header panel, and the bolts holding it on back by the door.

Jun 03, 2010 | 1994 Mercury Topaz

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...