Question about Cars & Trucks

Open Question

Scania R480 cylinder head bolt torque settings

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: head bolts torque settings

According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Posted on Feb 07, 2009

  • 1 Answer

SOURCE: Angle Torque settings head bolts

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Posted on Mar 17, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

  • 1 Answer

SOURCE: torque setting cylinder head bolt 4 cylinder KIA sportage

I need the torque settings and pattern for a Kia Sportage 2.2

Posted on Jan 28, 2010

  • 181 Answers

SOURCE: Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS

You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Posted on Feb 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is torque settings for head bolts on Kia pregio 2001


What are the cylinder head torque settings for a KIA K2700

www.answers.com > ... > Categories > Cars & Vehicles > Asian Cars > Kia
What is the torque specification for the cylinder head on a 2002 Kia Sportage? ... the correct torque for cylinder head bolt of kia pregio 2.7 diesel is 130-135ft-lbs. ... Thehead bolt torque settings, on your Kia 2.7 diesel engine, is 70 pounds per ...

Aug 17, 2015 | Kia Cars & Trucks

2 Answers

What is the cylinder head bolt torque settings fir a 4g69 mitsubishi engine ?


BOLT INSTALLATION


Apply engine oil to the thread of the bolts and to the washers.
Tighten the bolts to the specified torque, using the tightening sequence shown.
Tightening torque: 54 ft-lb +/- 2 ft-lb
Loosen all bolts fully in the reverse order of tightening.
Re-tighten the loosened bolts to the specified torque in the tightening sequence shown.
Tightening torque: 15 ft-lb +/- 1 ft-lb
This step is to make it easier to ensure you are making 90 degree turns. Make a paint mark across each bolt head and cylinder head.
Tighten the cylinder head bolts 90 degrees in the specified order.
Tighten the bolts another 90 degrees in the specified order and check that the paint marks on the cylinder head bolts are aligned with the paint marks on the cylinder head.
Link to the guide for this engine: http://www.mivec.co.nz/tech/4G9x_Engine_Manual.pdf



Aug 04, 2014 | 2007 Mitsubishi Outlander 2.4

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

Need torque settings for cylinder head bolts on a 52 reg skoda fabia 1.4 16v any help much appreciated thanks


Torque settings for cylinder head bolts for Skoda Fabia 1.4 16v

Cylinder head bolts tightening order:

tdisline_116.jpg

IMPORTANT NOTE: RENEW BOLTS!

Stage 1: Tightening torque = 30 Nm
Stage 1: Tightening torque = 90 Degrees
Stage 1: Tightening torque = 90 Degrees

Please do rate my response. Thanks!

Dec 17, 2010 | Volkswagen Polo Cars & Trucks

1 Answer

Looking for head bolt troque spec for 3.4l impala sfi04


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence-3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence-3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Nov 26, 2010 | 2004 Chevrolet Impala

    2 Answers

    Head gasket torque specifications and sequense


    Please don't forget to rate. Thank you:

    Left side front cylinder head


    98e175a.gif
    Cylinder head bolt torque sequence—3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence—3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Mar 06, 2010 | 2001 Chevrolet Venture

    2 Answers

    Torque setting cylinder head bolt 4 cylinder KIA sportage


    I need the torque settings and pattern for a Kia Sportage 2.2

    Nov 24, 2009 | 2001 Kia Sportage

    1 Answer

    Head bolt toqure


    Hope this helps, from autozone site. Curt
    Application:
    Cylinder head bolt torque sequence

    Note :
    Torque sequence:
    ---------
    front | 3 1 6 |
    of | |
    vehicle | 5 2 4 |
    ---------
    Step 1: Lightly oil cylinder bolt threads & washers
    Step 2: Torque to 22 Ft/Lbs
    Step 3: Torque to 51 Ft/Lbs
    Step 4: Loosen all bolts 180 degrees
    Step 5: Loosen all bolts 180 degrees
    Step 6: Torque bolts 1 & 2 to 25 Ft/Lbs
    Step 7: Torque bolts 3, 4, 5, 6 to 11 Ft/Lbs
    Step 8: Turn all bolts an additional 80 to 90 degrees
    Step 9: Turn all bolts an additional 80 to 90 degrees
    *** CAUTION ***
    engine uses Torque To Yield head bolts (TTY) that
    permanently stretch during the initial installation.
    New head bolts must be used when cylinder head is
    replaced or re-installed to obtain proper Torque.

    Apr 24, 2009 | 1995 Subaru Legacy

    1 Answer

    Need to know cylinder head bolt torque specs


    Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

    Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    275 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75744 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...